Free English DVDO DVDO-XTEND-USBC-USB-100 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD DVDO DVDO-XTEND-USBC-USB-100 (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What is the DVDO DVDO-XTEND-USBC-USB-100 and what is its primary function?
The DVDO DVDO-XTEND-USBC-USB-100 is a USB extender designed to transmit USB 3.2 Gen 1 signals up to 100m/328ft using a single CAT6a cable. It facilitates long-distance USB signal transmission between USB sources (like a host computer) and various USB devices such as webcams, PTZ cameras, keyboards, mice, USB microphones, flash drives, printers, and touch panel displays.
The transmitter features one USB-C host port, one USB-C device port, and two USB-A device ports. The receiver has two USB-C and two USB-A device ports. It also supports bi-directional 24V PoC (Power over Cable), which allows power to be supplied to either the transmitter or the receiver, with the other unit being powered over the CAT6a cable.
Is a surge protection device recommended for the DVDO DVDO-XTEND-USBC-USB-100?
Yes, the use of surge protection systems is highly recommended. This product contains sensitive electrical components that can be damaged by electrical spikes, surges, electric shock, and lighting strikes. Using a surge protection device helps to protect and extend the life of your equipment.
What is the required connection method for the UTP connectors on the DVDO DVDO-XTEND-USBC-USB-100?
The product requires the use of UTP connectors and must be connected using the direct interconnection method (T568B). You should not cross-connect the wires. The pinout for the T568B standard is as follows:
Pin 1: White and Orange
Pin 2: Orange
Pin 3: White and Green
Pin 4: Blue
Pin 5: White and Blue
Pin 6: Green
Pin 7: White and Brown
Pin 8: Brown
What are the key features of the DVDO DVDO-XTEND-USBC-USB-100?
Extension of USB 3.2 Gen 1 up to 100m/328ft via CAT6a cable
USB 3.2 Gen 1 connectivity with data transfer rate up to 5Gbps
Backwards compatible with USB 2.0 and 1.1
Hardware acceleration for isochronous and bulk transfer
TX features 1x USB-C host port, 1x USB-C and 2x USB-A device ports
RX features 2x USB-C (1x 5V@1A and 1x 5V@1.5A) and 2x USB-A device ports (1x 5V@1A and 1x 5V@1.5A)
Support bi-directional 24V PoC (Power over Cable), when TX or RX gets power, the other end does not need an external power supply
Plug-and-play with no drivers, downloads, or software required
What is included in the package for the DVDO DVDO-XTEND-USBC-USB-100?
① 1 x USB 3.2 Gen 1 Extender (Transmitter)
② 1 x USB 3.2 Gen 1 Extender (Receiver)
③ 1 x 24V/3.75A Power Supply
④ 2 x 4pin-3.5mm Phoenix Connectors (Male)
⑤ 4 x Mounting Ears
⑥ 8 x Machine Screws (KM3*4)
⑦ 1 x User Manual
What are the specifications of the DVDO DVDO-XTEND-USBC-USB-100?
Technical
| USB Protocol | USB 3.2 Gen 1 |
| Transmission Rate | Up to 5Gbps |
| Transmission Distance | 100m/328ft via CAT6a (F/FTP) cable 1.5m/4.9ft via USB cable |
| ESD Protection | IEC 61000-4-2: ±8kV (Air-gap discharge), ±4kV (Contact discharge) |
Connections
| Transmitter | Input: 1× HOST [USB Type C, 24-pin female] Output: 1× USB-C DEVICE [USB Type C, 24-pin female] 2× USB-A DEVICE [USB Type A, 9-pin female] 1× HDBT-USB3 [RJ45 connector, 24V PoC] Control: 1× RS-232 [3pin-3.5mm phoenix connector] 1× FSYNC [1pin-3.5mm phoenix connector] 1× SERVICE [USB Type C, firmware update port] |
| Receiver | Input: 1× HDBT-USB3 [RJ45 connector, 24V PoC] Output: 2× USB-A DEVICE [USB Type A, 9-pin female] 2× USB-C DEVICE [USB Type C, 24-pin female] Control: 1× RS-232 [3pin-3.5mm phoenix connector] 1× FSYNC [1pin-3.5mm phoenix connector] 1× SERVICE [USB Type C, firmware update port] |
Mechanical
| Housing | Metal Enclosure |
| Color | Black |
| Dimensions | TX / RX: 100mm [W] × 85mm [D] x 25.5mm [H] |
| Weight | TX: 265g; RX: 275g |
| Power Supply | Input: AC 100~240V 50/60Hz Output: DC 24V/3.75A |
| Power Consumption | TX: 23W (Max); RX: 35W (Max); TX+RX: 68W (Max, including line loss) |
| Operating Temperature | 0°C ~ 40°C / 32°F ~ 104°F |
| Storage Temperature | -20°C ~ 60°C / -4°F ~ 140°F |
| Operating Humidity | 20%~80% relative humidity, non-condensing |
| Storage Humidity | 10%~90% relative humidity, non-condensing |
What are the functions of the ports and indicators on the Transmitter Panel of the DVDO DVDO-XTEND-USBC-USB-100?
| No. | Name | Function Description |
|---|---|---|
| 1 | HOST | Uplink USB-C port, connected to PC or host. It can be used for HUB firmware update. |
| 2 | USB DEVICES (1) | Downlink USB-C port, connected to USB devices such as U disk or hard disk. Its output power is up to 5V/1A. |
| 3 | USB DEVICES (2~3) | Downlink USB-A port, connected to USB devices such as U disk or hard disk. Its output power is up to 5V/1A. |
| 4 | USB LED | USB signal indicator. • On: USB 3.0 signal is detected. • Blinking: USB 2.0 signal is detected. • Off: USB signal is not detected. |
| 5 | HDBT-USB3 | Connects to the HDBT-USB3 port on Receiver with CAT6a cable. It can also be used for 24V PoC power supply. |
| 6 | LINK LED | Connection signal indicator. • On: Transmitter and Receiver are connected and linked. • Off: Transmitter and Receiver are not connected. |
| 7 | RS-232 | 3pin phoenix connector, connected to a PC or control system for RS-232 command pass-through. |
| 8 | FSYNC | FSYNC port, the level pass through from Transmitter to Receiver, to synchronize the external devices. Default level range is 0~5V. |
| 9 | SERVICE | USB-C port for firmware update, supporting USB 2.0. |
| 10 | Power LED | The LED will be on when the transmitter is powered on. |
| 11 | DC 24V | DC 24V/3.75A power input port. |
What are the functions of the ports and indicators on the Receiver Panel of the DVDO DVDO-XTEND-USBC-USB-100?
| No. | Name | Function Description |
|---|---|---|
| 1 | USB DEVICES 1 | Downlink USB-C port, connected to USB devices such as U disk or hard disk. Its output power is up to 5V/1.5A. |
| 2 | USB DEVICES 2 | Downlink USB-C port, connected to USB devices such as U disk or hard disk. Its output power is up to 5V/1A. |
| 3 | USB DEVICES 3 | Downlink USB-A port, connected to USB devices such as U disk or hard disk. Its output power is up to 5V/1.5A. |
| 4 | USB DEVICES 4 | Downlink USB-A port, connected to USB devices such as U disk or hard disk. Its output power is up to 5V/1A. |
| 5 | USB LED | USB signal indicator. • On: USB 3.0 signal is detected. • Blinking: USB 2.0 signal is detected. • Off: USB signal is not detected. |
| 6 | HDBT-USB3 | Connects to the HDBT-USB3 port on Transmitter with CAT6a cable. It can also be used for 24V PoC power supply. |
| 7 | LINK LED | Connection signal indicator. • On: Transmitter and Receiver are connected and linked. • Off: Transmitter and Receiver are not connected. |
| 8 | RS-232 | 3pin phoenix connector, connected to a PC or control system for RS-232 command pass-through. |
| 9 | FSYNC | FSYNC port, the level pass through from TX to RX, to synchronize the external devices. Default level range is 0~5V. |
| 10 | SERVICE | USB-C port for firmware update, supporting USB 2.0. |
| 11 | Power LED | The LED will be on when the receiver is powered on. |
| 12 | DC 24V | DC 24V/3.75A power input port. |
How do I set up and connect the DVDO DVDO-XTEND-USBC-USB-100?
1. Connect your host computer to the USB-C HOST port on the Transmitter (TX) unit.
2. Connect your local USB peripherals, such as a keyboard and mouse, to the USB-A and USB-C DEVICE ports on the Transmitter unit.
3. Connect a CAT6a cable between the HDBT-USB3 port on the Transmitter and the HDBT-USB3 port on the Receiver (RX) unit.
4. Connect your remote USB devices, such as a USB Camera or U Disk, to the USB-A and USB-C DEVICE ports on the Receiver unit.
5. Connect the included 24V power supply to the DC 24V port on either the Transmitter or the Receiver. Due to the bi-directional PoC (Power over Cable) feature, only one power supply is needed to power both units.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD DVDO DVDO-XTEND-USBC-USB-100 (01) PDF DOCUMENT