DIGITECH XC0432 (01) PDF Document

Step 1. Press and hold [CLOCK] button for 2 seconds until “12 or 24Hr” flashes.

Step 2. Use [UP]/[DOWN] button to adjust, and press [CLOCK] button to proceed to the next setting.

Step 3. Repeat Step 2 above for setting of HOUR, MINUTE, SECOND, YEAR, MONTH, DATE, HOUR OFFSET, LANGUAGE and DST.

Note:

1. The unit will automatically exit setting mode if no button was pressed in 60 seconds.

2. Range of hour offset is between -23 and +23 hours.

3. The language options are English (EN), French (FR), German (DE), Spanish (ES), and Italian (IT).

4. For above mentioned “DST” setting, the actual product does not have this feature, as it is Non-RC version.

Step 1. Press the [ALARM] button anytime to show the alarm time.

Step 2. Press [ALARM] button to activate the alarm.

Step 3. Press again to activate alarm with ice-alert function.

Step 4. To disable the alarm, press until the alarm icon disappears.

Step 1. Press and hold [ALARM] button for 2 seconds to enter alarm setting mode. HOUR will begin to flash.

Step 2. Use [UP]/[DOWN] button to adjust HOUR, and press [ALARM] button to proceed to set MINUTE.

Step 3. Repeat Step 2 above to set MINUTE, then press [ALARM] button to exit.

Note: Pressing the [ALARM] button twice when alarm time is being displayed will activate the temperature-adjusted pre-alarm. The alarm will sound 30 minutes earlier if it detects outside temperature is below -3°C.

Press and hold [BARO] button for 2 seconds to toggle between:

• ABSOLUTE: the absolute atmospheric pressure of your location
• RELATIVE: the relative atmospheric pressure based on the sea level

Step 1. Get the atmospheric pressure data of the sea level (it is also the relative atmospheric pressure data of your home area) through the local weather service, internet and other channels.

Step 2. Press and hold [BARO] button for 2 seconds until “ABSOLUTE” or “RELATIVE” icon flashes.

Step 3. Press [UP]/[DOWN] button to switch to “RELATIVE” mode.

Step 4. Press [BARO] button once again until the “RELATIVE” atmospheric pressure digit flashes.

Step 5. Press [UP]/[DOWN] button to change its value.

Step 6. Press [BARO] button to save and exit the setting mode.

Note:

1. The default relative atmospheric pressure value is 1013 mb/hPa (29.91 inHg), which refers to the average atmospheric pressure.

2. When you change the relative atmospheric pressure value, the weather indicators will change along with it.

3. The built-in barometer can notice the environmental absolute atmospheric pressure changes. Based on the data collected, it can predict the weather conditions in the forthcoming 12 hours. Therefore, the weather indicators will change according to the detected absolute atmospheric pressure after you operate the clock for 1 hour.

4. The relative atmospheric pressure is based on the sea level, but it will change with the absolute atmospheric pressure changes after operating the clock for 1 hour.

Step 1. Press the [BARO] button to enter unit setting mode.

Step 2. Use the [BARO] button to change the unit between inHg (inches of mercury) / mmHg (millimeter of mercury) / mb (millibars per hectopascal) /hPa.

Step 3. Press [BARO] button to confirm.

The device displays how many mm / inches of rain are accumulated in a one hour time period, based on current rainfall rate.

Press [RAINFALL] button to toggle between:

• RATE: Current rainfall rate in past an hour
• DAILY: The DAILY display indicate the total rainfall from midnight
• WEEKLY: The WEEKLY display indicate the total rainfall from the current week
• MONTHLY: The MONTHLY display indicate the total rainfall from the current calendar month

Note: Rain rate is updated every 6 minutes, at every hour on the hour, and at 6, 12, 18, 24, 30, 36, 42, 48, 54 minute past the hour.

Step 1. Press and hold [RAINFALL] button 2 seconds to enter unit setting mode.

Step 2. Use [UP] / [DOWN] button to toggle between mm (millimeter) and in (inch).

Step 3. Press [RAINFALL] button to confirm and exit.

Wind Direction Indicator Meaning

Real-time wind direction

Wind directions appeared in last 5 minutes (max 6)

Press [WIND] button to toggle between:

• AVERAGE: The AVERAGE wind speed will display the average of all wind speed numbers recorded in the previous 30 seconds
• GUST: The GUST wind speed will display the highest wind speed recorded from last reading

The wind level provides a quick reference on the wind condition and is indicated by a series of text icons:

Step 1. Press and hold [WIND] button for 2 seconds to enter unit setting mode.

Step 2. Use the [UP] / [DOWN] button to change the unit between mph (miles per hour) / m/s (meter per second) / km/h (kilometer per hour) / knots.

Step 3. Press [WIND] button to confirm and exit.

Press the [INDEX] button repeatedly until WINDCHILL displays.

Note: The wind chill factor is based on the combined effects of temperature and wind speed. The wind chill displayed is calculated solely from temperature and humidity measured from the 5-in-1 sensor.

Press the [INDEX] button repeatedly until HEAT INDEX displays.

Note: Heat index is only calculated when temperature is 27°C/80°F or above, and based solely from the temperature and humidity measured from the 5-in-1 sensor.

Press the [INDEX] button repeatedly until DEWPOINT displays.

Note: The dew point is the temperature below which the water vapor in air at constant barometric pressure condenses into liquid water at the same rate at which it evaporates. The condensed water is called dew when it forms on a solid surface. The dewpoint temperature is calculated from the indoor temperature and humidity measured at the Main Unit.

The Display main unit automatically record and display data of past 24 hours on the hour.

To check all the history data in the past 24 hours, press the [HISTORY] button.

E.g. Current time 7:25 am, Mach 28

Press [HISTORY] button repeatedly to view past readings at 7:00am, 6:00am, 5:00am, 5:00am (Mar 27), 6:00am (Mar 27), 7:00am (Mar 27)

The LCD will display the past indoor and outdoor temperature & humidity, value of air pressure, wind chill, wind speed, rainfall and their time and date.

Step 1. Press [MAX/MIN] button to check the maximum/minimum records. The checking orders will be: Outdoor max temperature → Outdoor min temperature → Outdoor max humidity → Outdoor min humidity → Indoor max temperature → Indoor min temperature → Indoor max humidity → Indoor min humidity → Outdoor max wind chill → Outdoor min wind chill → Outdoor max heat index → Outdoor min heat index → Indoor max dewpoint → Indoor min dewpoint → Max pressure → Min pressure → Max average → Max gust → Max rainfall.

Step 2. Press and hold [MAX/MIN] button for 2 seconds to reset the maximum and minimum records.

Note: When maximum or minimum reading is displayed, the corresponding timestamp will be shown.

HI/LO alert are used to alert you of certain weather conditions. Once activated, the alarm will turn on and amber LED starts flashing when a certain criterion is met. The following are areas and type of alert provided:

Note: * Daily rainfall since midnight.

Step 1. Press the [ALERT] button until the desired area is selected.

Step 2. Use [UP] / [DOWN] buttons to adjust the setting.

Step 3. Press [ALERT] button to confirm and continue to next setting.

Step 1. Press [ALERT] button until the desired area is selected.

Step 2. Press [ALARM] button to turn the alert on or off.

Step 3. Press [ALERT] button to continue to next setting.

Note:

1. The unit will automatically exit setting mode in 5 seconds if no button is pressed.

2. When ALERT alarm is on, the area and type of alarm that triggered the alarm will be flashing and the alarm will sound for 2 minutes.

3. To silence the Alert alarm beeping, press the [SNOOZE / LIGHT] / [ALARM] button, or let the beeping alarm automatically turn off after 2 minutes.

The comfort indication is a pictorial indication based on indoor air temperature and humidity in an attempt to determine comfort level.

Note:

1. Comfort indication can vary under the same temperature, depending on the humidity.

2. There is no comfort Indication when temperature is below 0°C (32°F) or over 60°C (140°F).

During installation of the wireless 5-in-1 sensor, the sensors were likely to be triggered, resulting in erroneous rainfall and wind measurements. After the installation, user may clear out all the erroneous data from the Display Main Unit, without needing to reset the clock and re-establish pairing.

Simply press and hold the [HISTORY] button for 10 seconds. This will clear out any data recorded before.

The outdoor 5-in-1 sensor is calibrated to be pointing to North by default. However, in some cases, users may wish to install the product with the arrow pointing towards the South, especially for people living in the Southern hemisphere (e.g. Australia, New Zealand).

Step 1. First install the outdoor 5-in-1 sensor with its arrow pointing to the South. (Please refer to Installation session for mounting details)

Step 2. On the Display main unit, press and hold [WIND] button for 8 seconds until the upper part (Northern Hemisphere) of the compass lights up and blinking.

Step 3. Use [UP] / [DOWN] to change to lower part (Southern Hemisphere).

Step 4. Press [WIND] button to confirm and exit.

Note: Changing from hemisphere setting will automatically switch the direction of the moon phase on the display.

Step 1. Rotate the rain collector by 30° anticlockwise.

Step 2. Gently remove the rain collector.

Step 3. Clean and remove any debris or insects.

Step 4. Install all the parts when they are fully clean and dried.

Step 1. Unscrew the 2 screws at the bottom of the radiation shield.

Step 2. Gently pull out the shield.

Step 3. Remove carefully any dirt or insects inside the sensor casing (Do not let the sensors inside get wet).

Step 4. Clean the shield with water and remove any dirt or insects.

Step 5. Install all the parts back when they are fully clean and dried.

Step 1. Check the drain hole in the rain collector.

Step 2. Check the balance indicator.

Step 1. Check the radiation shield.

Step 2. Check the sensor casing.

Step 1. Check wind cups (Anemometer).

Step 2. Check the wind vane.

Step 1. Relocate the main unit and 5-in-1 sensor closer to each other.

Step 2. Make sure the main unit is placed away from other electronic appliances that may interfere with the wireless communication (TVs, computers, microwaves).

Step 3. If problem continues, reset both main unit and 5-in-1 sensor.

• Read and keep these instructions
• Heed all warnings
• Follow all instructions
• Do not subject the unit to excessive force, shock, dust, temperature or humidity
• Do not cover the ventilation holes with any items such as newspapers, curtains etc
• Do not immerse the unit in water. If you spill liquid over it, dry it immediately with a soft, lint-free cloth
• Do not clean the unit with abrasive or corrosive materials
• Do not tamper with the unit’s internal components. This invalidates the warranty
• Only use fresh batteries. Do not mix new and old batteries
• Only use attachments / accessories specified by the manufacturer
• Images shown in this manual may differ from the actual display
• When disposing of this product, ensure it is collected separately for special treatment
• Placement of this product on certain types of wood may result in damage to its finishing for which manufacture will not be responsible. Consult the furniture manufacturer’s care instructions for information.
• The contents of this manual may not be reproduced without the permission of the manufacturer
• When replacement parts are required, be sure the service technician uses replacement parts specified by th manufacturer that have the same characteristics as the original parts. Unauthorized substitutions may result in fire, electric shock, or other hazards.
• Do not dispose old batteries as unsorted municipal waste. Collection of such waste separately for specia treatment is necessary.
• Please note that some units are equipped with a battery safety strip. Remove the strip from the batter compartment bef first use.
• The technical specifications for this product and the contents of the user manual are subject to change without notice.