DEWALT JOBSITE PRO DXMA1901148 (01) PDF MANUAL

The package contains the following:

• Jobsite Pro Wearable Speaker

• Type C Charging Cable

• 2 Detachable Mounting Magnets

• User Manual

JOBSITE PRO WEARABLE SPEAKER:

1. Speaker

2. On/Off Button

3. Volume Controls

4. Microphone

5. Type C Charge Port

6. Clip

7. Detachable Mounting Magnet

CHARGER CONNECTOR CABLE:

1. Type C to USB

WARNING: DO NOT leave speaker in any location with excessive heat.

WARNING: DO NOT charge or use the battery in explosive atmospheres, such as in the presence of flammable liquids, gases or dust.

WARNING: DO NOT modify the battery in any way to fit a non-compatible charger as the battery may rupture causing serious personal injury.

WARNING: DO NOT splash or immerse in water or other liquids.

WARNING: DO NOT store or use the speaker in locations where the temperature may reach or exceed 105° F (40° C) (such as outside sheds or metal buildings in summer). For best life, store speaker in a cool, dry location. The speaker should not be disposed of as municipal solid waste.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

WARNING: Fire hazard. Never attempt to open the battery pack for any reason. If the battery pack is cracked or damaged, do not insert the charging cable. Do not crush, drop or damage the battery. Do not use the speaker if it has received a sharp blow, been dropped, run over or damaged in any way (e.g. pierced with a nail, hit with a hammer, stepped on).

Damaged batteries should be returned to a service center for recycling.

Connect the Type C end of the charging cable into the speaker and the USB end into a power source. Make sure the speaker is fully charged before using it for the first time.

*Charger sold separately.

WARNING: ONLY CHARGE with certified USB adapter DC5V/0.5A

Press and hold the speaker’s ON/OFF button for 2 seconds to turn the speaker on. If not previously paired, the speaker will automatically enter pairing mode. If the speaker has been previously paired, it will automatically enter pairing mode after 20 seconds of reconnecting timeout.

Alternatively, if the speaker is turned off, you can press and hold the ON/OFF button for 6 seconds to enter pairing mode.

• When turning on the speaker, you will hear, “POWER ON – Battery HIGH (or MEDIUM or LOW)-Pairing.” While in pairing mode, the speaker’s LED light will flash red and blue. If unable to connect to a previously paired device after 20 seconds, the speaker will remain in pairing mode and will automatically turn off after 3 minutes of unsuccessful connection.

• Turn on the Bluetooth function of your Bluetooth device and pair the speaker with your Bluetooth device.

• When successfully connected to a phone or other Bluetooth device, the speaker’s blue LED light will stay on for 1 second and you will hear, “Your device is connected”.

Turn on the Bluetooth function of your Bluetooth device and select “DEWALT WEARABLE SPEAKER”. Enter the speaker’s password “0000” if prompted. For Bluetooth devices featuring Bluetooth 3.0 or higher, no need to enter a password.

If you have another Bluetooth device that you want to pair with the speaker, make sure the Bluetooth function in any other previously paired or connected devices are turned off. You will hear, “Your device is disconnected.” Then follow the steps in “PAIR THE SPEAKER WITH YOUR BLUETOOTH DEVICE.”

Turn on the Bluetooth function of your Bluetooth device. Press and hold the speaker’s ON/OFF button for 2 seconds to turn the speaker on. The speaker will search for the previously connected Bluetooth device and reconnect to it automatically. If the last connected device is not available, the speaker will search and reconnect to the next most recently connected device. If no device is found, the speaker will automatically turn off after 3 minutes.

To turn speaker ON: Press and hold the ON/OFF button for 2 seconds.

To turn speaker OFF: Press and hold the ON/OFF button for 3 seconds.

To play or pause music: Press the ON/OFF button once.

• Forward (next song): Press and hold “+” button for 1 second

• Volume increase: Press “+” button

• Backward (previous song): Press and hold “-” button for 1 second

• Volume decrease: Press “-” button

Use the ON/OFF button for the following functions:

Answer/Hang up: Press the ON/OFF button.

Reject incoming call: Press and hold the ON/OFF button for 1 second.

Switch caller during call: Double-click the ON/OFF button.

Voice Control – Siri/Google: Double-click the ON/OFF button.

Speaker is powered on: The Red and Blue LED flashes 1 second.

Speaker is pairing to a Bluetooth device: The Red and Blue LED flashes alternately.

Speaker is connected to a Bluetooth device: The Blue LED stays on for 1 second.

Speaker is powered on and not connected to a Bluetooth device: The Red and Blue LED flashes. If no connection can be made, the speaker will power itself off after 3 minutes.

100% power: Green LED light stays on until cable is disconnected.

80% – 99% power: Green LED light flashes.

20% – 80% power: Blue LED light flashes.

0% – 20% power: Red LED light flashes.

The Red LED light will flash 2 times per second and you will hear the “battery low” tone once every minute.

The speaker features an IP56 rating for protection against dust and water.

1. Long press the ON/OFF button for 6 seconds on a turned off device to enter pairing mode.

2. Once in pairing mode, double click the ON/OFF button to reset. You will hear a beep and the red and blue lights will flash 5 times simultaneously.

Note: If your speaker was previously paired, be sure to “Forget this device” or “Unpair” in your Bluetooth device’s “paired devices” list before resetting.

Music time: Up to 10 Hours

Talk time: Up to 8 Hours

Standby time: >10 Days

Charging time: Approximately 1.5 Hours

Rechargeable Li-ion battery: 3.7V 560 mAh

Bluetooth version: 5.1

Compatible Bluetooth profiles: HFP, HSP, A2DP, AVRCP

Supported audio codec: SBC

Operating range: 10 Meters (33 Feet)

The battery is not fully charged out of the box. Before using the speaker, read the safety instructions below and then follow the charging procedures outlined.

Do not incinerate the battery module even if it is severely damaged or is completely worn out. The battery can explode in a fire. Toxic fumes and materials are created when lithium batteries are burned. If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture of liquid organic carbonates and lithium salts. Contents of opened battery cells may cause respiratory irritation. Provide fresh air. If symptoms persist, seek medical attention. This speaker is splash and water resistant and was tested under controlled laboratory conditions with a rating of IP56 under IEC standard 60529. Splash and water resistance are not permanent conditions and resistance might decrease as a result of normal wear. Do not attempt to charge a wet speaker. To dry your speaker, tap it gently against your hand with the port cover open to remove excess liquid. Leave your speaker in a dry area with some airflow. Placing your speaker in front of a fan blowing cool air directly onto the speaker might help the drying process.

1. The best storage place is one that is cool and dry, away from direct sunlight and excess heat or cold.

2. For long storage, it is recommended to store the speaker in a cool dry place for optimal results.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.