DELI T088 (01) PDF Document

To ensure safe operation of the DELI T088, please adhere to the following safety guidelines:

Place the machine on a stable surface and ensure it does not tip over to prevent falling and operational failure.

Do not disassemble, transform, or repair the machine yourself to avoid electric shock or injury.

Avoid touching the power plug with wet hands.

Unplug the power supply when dumping debris, moving the unit, or when it will not be used for an extended period.

Do not splash water on the machine or use it near heating or cooling devices, or in areas with high temperatures, humidity, or excessive dust.

Do not place adhesive tape, carbon paper, fabric, or plastic film into the machine for crushing, as this may cause failure.

Do not damage the power cord or place heavy objects on it.

If abnormal conditions like smoke or odor occur, immediately cut off the power supply and stop use.

Do not use the machine if there is any damage to the unit or the power cord.

Keep the machine out of reach of children due to internal blades.

Do not touch the blades of the paper inlet or outlet with your hands.

Avoid entangling ties, necklaces, sleeves, or hair into the paper inlet. If entanglement occurs, press and hold the reverse button.

Do not put pins or paper clips into the paper inlet. If they become entangled, press and hold the reverse button.

Do not blow flammable gases toward the machine.

Be aware of moving parts and sharp edges; keep away from moving components.

When loading paper into the DELI T088 storage bin, follow these requirements:

Staples: For stacks bound by staples, do not exceed 5 sheets. Place the paper into the storage bin with the stapled corner in the upper left or right corner. Heavy-duty staples are prohibited.

Prohibited Items: Do not load documents bound with glue or iron rings. Do not load binders of any material, paper clips, credit cards, discs, or letter/document bags.

Paper Size: A3 paper is allowed only if it is folded in half. Standard A4 paper is acceptable.

The specifications for the DELI T088 Automatic Shredder are as follows:

To maintain your DELI T088, follow these steps:

1. Always unplug the power before performing any maintenance.

2. Maintenance is limited to cleaning the external parts of the machine.

3. When cleaning the exterior, use a soft cloth dipped in soft soapy water or mild detergent. Gently wipe the casing, ensuring no water drips into the interior of the machine.

4. Do not use organic solvents such as gasoline, benzene, or diluents for cleaning.

5. Ensure the wiping cloth does not fall into the paper inlet during cleaning.

To install the casters on the DELI T088, remove the casters from the packaging. Install the two casters equipped with brakes on the front side of the shredder (the side with the visible window). Install the two casters without brakes on the back side of the shredder.

Operation instructions for the DELI T088:

1. Connect the unit to a 230V power supply.

2. Press the power switch button. The indicator will turn on, and the machine will enter standby mode.

3. Manual Shredding: Feed paper directly into the manual paper inlet. The paper shredding light will turn green, indicating the process has begun.

4. Automatic Shredding: Press the storage bin opening button to open the cover. Place up to 200 sheets of 70g A4 paper into the internal storage bin and close the cover. The Paper Loaded light will turn on. Press the Shredding key; the Shredding light will turn green to start the automatic process.

5. Pausing or Reversing: Briefly press the Pause/Retreat key to pause shredding. Press and hold the Pause/Retreat key to reverse the machine and retreat the paper.

Note: Automatic and manual shredding cannot be used simultaneously.

The DELI T088 uses various indicators to signal its status and required actions:

Clear the scrap bin: This indicator means the scrap bin is full or needs to be reset. Clear and reset the bin to resume operation.

Close the box door: This light indicates the scrap bin is not properly seated. Reset the scrap bin to clear the light.

Clear the jammed paper: This light turns on when excessive paper is inserted into the manual inlet or a jam occurs in the storage bin. For manual jams, the machine will reverse; open the cover to remove the paper. For storage bin jams, open the bin and organize the paper.

Overheat/Waiting: This light indicates the machine has reached its thermal limit. Wait approximately 60 minutes for the machine to cool down before resuming use.

Close the cover: This light indicates the storage bin cover is open. Properly reset the cover to resume shredding.

Paper Loaded: Indicates there is paper currently in the storage bin.

Without paper: Indicates the storage bin is empty.

Use the following table to troubleshoot issues with the DELI T088: