CRAFTSMAN 139.53999 (01) PDF Document

To prevent possible SERIOUS INJURY or DEATH from electrocution:

• Be sure power is NOT connected BEFORE installing door control.

• Connect ONLY to 7-28 VOLT low voltage wires.

To prevent possible SERIOUS INJURY or DEATH from a closing garage door:

• Install door control within sight of garage door, out of reach of children at a minimum height of 5 feet (1.5 m), and away from ALL moving parts of door.

• NEVER permit children to operate or play with door control push buttons or remote control transmitters.

• Activate door ONLY when it can be seen clearly, is properly adjusted, and there are no obstructions to door travel.

• ALWAYS keep garage door in sight until completely closed. NEVER permit anyone to cross path of closing garage door.

• DO NOT install this door control on garage door opener systems controlling one-piece or swing doors.

To provide an adequate visual alert, the garage door opener light bulb(s) MUST be a minimum of 40 Watt (or equivalent).

The CRAFTSMAN 139.53999 Assurelink™ Control Panel is intended to be installed with Craftsman® Security+™ Garage Door Openers manufactured between 1998 and the present. It is NOT compatible with Security+ 2.0™ Garage Door Openers. Additionally, DO NOT install this door control on garage door opener systems controlling one-piece or swing doors.

Install the control panel in place of the existing door control. Note that due to power consumption, this control panel cannot be used with another wired door control.

1. Disconnect all electrical and battery power (if applicable) to the garage door opener.

2. Remove the existing door control from the wall.

3. Note the polarity of the wires connected to the existing door control. Label the wire connected to the RED terminal and the wire connected to the WHITE terminal. Disconnect the wires from the existing door control.

4. Connect the wires to the new control panel. Make sure the polarity is correct:

• Red wire to the R terminal.

• White wire to the W terminal.

5. Mount the control panel to the wall.

6. Reconnect power. The yellow command LED and the red learn LED will blink quickly for up to 5 minutes as the control panel recharges. When the control panel is operational, the yellow command LED will glow steadily.

7. To test the control panel, press the push bar to activate the garage door opener.

If the yellow command LED does not turn on, reverse the wires connected to the R and W terminals of the control panel. Replace the wire if necessary.

• If the yellow and red LEDs are blinking slowly, the control panel is not compatible with your garage door opener.

• If the yellow and red LEDs are blinking quickly, the control panel is charging, and may take up to 5 minutes to become operational.

1. Connect the Assurelink™ Internet Gateway to a router with the ethernet cable. If you only have access to a Wi-Fi signal and not a router, you must use a wireless ethernet adapter (not provided) to connect to the internet.

2. Connect power to the Assurelink™ Internet Gateway. The blue and green LEDs will blink momentarily and then the blue and green LEDs will light solid.

The Assurelink™ Control Panel has been programmed at the factory to the Assurelink™ Internet Gateway. If your garage door opener does not appear after registering your gateway, follow these steps:

1. In your account, click on “Manage Places > Add New Device > Garage Door Opener” and follow the directions.

2. Once you click ADD you have 3 minutes to press the LEARN button two times on the control panel. The red learn LED will turn on.

3. The red learn LED will turn off when programming is complete. The blue LED on the Assurelink™ Internet Gateway will light to indicate that a device has been programmed. Once the control panel is programmed, it will appear on your screen and you can then name the device (e.g., My Control Panel, etc.).

4. Click SAVE.

• GREEN On Solid – The Assurelink™ Internet Gateway has an IP address and is connected to the Internet.

• GREEN flashing steadily On & Off – The Assurelink™ Internet Gateway has an IP address, but is not accessing the internet. Check your router settings and internet connections.

• GREEN Off – The router is not providing an IP address to the Assurelink™ Internet Gateway. Check your router settings and internet connections.

To change the amount of time the garage door opener lights will stay on, press and hold the LOCK button until the garage door opener lights flash. The time interval is indicated by the number of flashes.

The Light Feature turns the lights on when someone enters through the open garage door and the safety reversing sensor infrared beam is broken.

Activate:

Start with the garage door opener lights on. Press and hold the LIGHT button until the garage door opener lights turn off, then on again (approximately 10 seconds).

Deactivate:

Press and hold the LIGHT button until the garage door opener lights turn on, then off again (approximately 10 seconds).

The motion sensor feature will automatically turn on the garage door opener lights when motion is sensed. The lights will come on for the set period of time, then shut off. To activate or deactivate this feature, slide the motion sensor switch ON or OFF.

The TTC feature automatically closes the door after 1, 5, or 10 minutes.

Activate:

Press and hold the ON button until one of the TTC LEDs light up. Then press the ON button again to cycle through the time interval options (the corresponding TTC LED will light for each time interval). The garage door opener light bulbs will blink as confirmation.

Deactivate:

Press and hold the OFF button until all TTC LEDs turn off and a beep is heard from the control panel.

Temporarily hold door open (suspend TTC):

Press and release the HOLD OPEN button. The HOLD OPEN button will begin to flash. Press the HOLD OPEN button again to resume normal TTC operation.

Activate:

Press and hold the LOCK button for 2 seconds. The command LED will flash as long as the lock feature is activated and your handheld remote control will not operate your door at this time. Your Assurelink™ keypad will continue to work.

Deactivate:

Press and hold the LOCK button again for 2 seconds. The command LED will stop flashing and normal operation will resume.

Erase all remote controls and keyless entries:

1. Press and hold the LEARN button on the control panel until the red learn LED goes out (approximately 6 seconds). All remote control and keyless entry codes are now erased. Reprogram any compatible accessory you wish to use.

NOTE: Erasing remote controls and keyless entries from the control panel does not erase them from the garage door opener; you need to erase the memory of the garage door opener separately.

Erase all devices (including Assurelink™ enabled accessories):

1. Press and hold the LEARN button on the control panel until the red learn LED goes out (approximately 6 seconds).

2. Immediately press and hold the LEARN button again until the red learn LED goes out. All codes are now erased. Reprogram any compatible accessory you wish to use.

1. Press the control panel LEARN button twice, the red learn LED will turn on.

2. Press the button on the remote control that you wish to operate your garage door.

3. The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed.

1. Press the control panel LEARN button twice, the red learn LED will turn on.

2. Enter a 4-digit personal identification number (PIN) of your choice on the keyless entry keypad. Then press the ENTER button.

3. The garage door opener lights will flash (or two clicks will be heard) when the code has been programmed.

1. Press the control panel LEARN button twice, the red learn LED will turn on.

2. Press the LEARN button on the Assurelink™ device.

• Model 139.30499 3-Button Remote Control

• Model 139.30498 3-Button Mini Remote Control

• Model 41A7633 3-Button Remote Control

• Model 139.3050 Wireless Keyless Entry

• Model 41A6147-10 Wireless Keyless Entry

• Model 139.34321 Remote Light Switch

• Model 139.21255 Remote Light Control

• Model 139.21242 Garage Door and Gate Monitor

• Model 41A7665 Assurelink™ Internet Gateway