CECOTEC READY WARM 800 THERMAL (01) PDF Document

The CECOTEC READY WARM 800 THERMAL is designed only for household use. Do not use it for industrial or commercial purposes.

Check the power cord regularly for visible damage. If the cord is damaged, it must be replaced by the official Technical Support Service of Cecotec in order to avoid any type of danger.

Do not cover the CECOTEC READY WARM 800 THERMAL in order to avoid overheating.

The installation of the CECOTEC READY WARM 800 THERMAL on the wall of a bathroom must always be done at a distance where no person in the shower or in the bath may reach it.

Do not use the CECOTEC READY WARM 800 THERMAL directly on the floor without installing the legs.

Do not place the CECOTEC READY WARM 800 THERMAL close to heat sources, flammable substances, wet surfaces or allow it to come into contact with water or other liquids. Do not operate outdoors. The appliance must not be placed immediately below a socket.

Allow the CECOTEC READY WARM 800 THERMAL to operate at maximum temperature for 2-3 hours in a ventilated place in order for the device to eliminate all manufacturing wastes.

The product’s surface will reach high temperatures during operation. Avoid skin from getting in contact with it and use the handle to move it.

Always use the CECOTEC READY WARM 800 THERMAL with the fins in a vertical position.

Keep the packaging materials out of the reach of children, they could be dangerous.

The CECOTEC READY WARM 800 THERMAL is not intended to be used by children under the age of 8. It can be used by children over the age of 8, as long as they are given continuous supervision.

This product can be used by children and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge, as long as they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.

Supervise young children to make sure that they do not play with the appliance. Close supervision is necessary when the appliance is being used by or near children.

Make sure that the mains voltage matches the voltage stated on the rating label of the CECOTEC READY WARM 800 THERMAL and that the wall outlet is grounded.

To unlock the CECOTEC READY WARM 800 THERMAL, press (-) for 3 seconds.

The CECOTEC READY WARM 800 THERMAL has 3 operating modes in Manual mode:

Day mode: The temperature can be adjusted from 5 °C to 35 °C.

Sleep mode: The temperature can be adjusted from 5 °C to 35 °C.

Anti-frost mode: The temperature can be adjusted from 5 °C to 15 °C.

For the CECOTEC READY WARM 800 THERMAL to be able to operate correctly, the set temperature must always be higher than the room one. The panel will display the room temperature. As the temperature shown on the display is the one next to the device and not the real room one, when setting the temperature, select a few more grades than desired ones.

Step 1. Connect the CECOTEC READY WARM 800 THERMAL to a power supply and turn the power switch on.

Step 2. The control panel will flash and the “°C” symbol, room temperature and power indicator will light up. If this last symbol does not light up, press it.

Step 3. Select the desired operating mode by pressing the corresponding button: Day, Sleep or Anti-frost. The display will show the selected mode.

Step 4. Use the + and – buttons to set the desired temperature for the selected mode. During the configuration of the temperature, the “C” icon will blink.

Step 5. Once the desired temperature has been set, the display will show the room temperature again.

Step 6. Repeat the before steps to set the temperature for the other modes.

Step 7. Use the on/off button to turn the heater on and off.

When the CECOTEC READY WARM 800 THERMAL device reaches the set temperature, it will automatically switch off and the icon will turn off.

When the room temperature falls below the set one on the CECOTEC READY WARM 800 THERMAL, the device will automatically turn back on and the icon will light up again.

The power indicator on the CECOTEC READY WARM 800 THERMAL may blink when the device is about to turn on or off.

The set temperatures on the CECOTEC READY WARM 800 THERMAL will be saved even if the device is disconnected or turned off and on.

To reset the CECOTEC READY WARM 800 THERMAL while it is connected to the power supply and the power switch is on, make sure the device is unlocked or unlock it with the remote control and press the power button (-) for 3 seconds. It can also be switched off and on.

Step 1. Long press the “PROG” button on the CECOTEC READY WARM 800 THERMAL until the display shows “00:00″.

Step 2. The hour digits will blink. Use the + and – buttons to set the desired hour and press “PROG” to save the settings.

Step 3. The minutes digits will blink. Use the + and – buttons to set the desired minutes and press “PROG” to save the settings.

Step 4. The display will show the week calendar (Monday-Sunday, 1-7). Select the current day by pressing + and -. Press “PROG” to save the settings.

Scheduling mode for the CECOTEC READY WARM 800 THERMAL has 3 operating modes:

Day mode: The temperature can be adjusted from 5 °C to 35 °C.

Sleep mode: The temperature can be adjusted from 5 °C to 35 °C.

Anti-frost mode: The temperature can be adjusted from 5 °C to 15 °C.

The temperature set manually will be applied to the modes during programmed operations.

If the CECOTEC READY WARM 800 THERMAL device is disconnected from the power supply, the schedule settings will be saved but the current day and time will be reset.

Step 1. The display on the CECOTEC READY WARM 800 THERMAL will show the first 2 bars for the first period of time (00:00 – 1:00 am) blinking. It will also show 1 as Monday.

Step 2. Press the desired mode (Day, Sleep or Anti-frost) for the selected time interval.

If you select Sleep mode, the display will show the icon and the bar on the top part will blink.

If you select the Anti-frost mode, the display will show the icon and the bar on the lower part will blink.

If you select Day mode, the display will show the icon and the top and lower bars will blink.

Step 3. Once the first period has been scheduled, press “+” and the next time period’s bars will blink.

Step 4. Repeat these steps up to 24 hours.

Step 5. When all the hours in a day have been scheduled, press “PROG” to end the selected day scheduling and repeat the steps to schedule the 7 days of the week.

Step 6. Once the whole week has been scheduled, press “PROG” and the device will automatically save the settings and operate in the set mode.

Step 1. During operation of the CECOTEC READY WARM 800 THERMAL, press twice the on button on the remote control.

Step 2. Use the + and – buttons to select the desired temperature.

Once the temperature is set, it will be saved for this mode for future operations, including under manual mode.

Step 1. Press the on button on the remote control twice.

Step 2. Press “PROG”.

Step 3. Select the desired mode and adjust the temperature if necessary, using the + and -buttons.

The remote control for the CECOTEC READY WARM 800 THERMAL requires 1 x CR2025 battery (included).

Remove the protection label from the battery compartment. If necessary, open the battery cover.

Step 1. Turn off, unplug the CECOTEC READY WARM 800 THERMAL from the power supply and allow it to cool down before cleaning or repairing it.

Step 2. Use a soft, dry and clean cloth to clean the product’s outer housing.

Step 3. Do not use abrasive cleaners or scouring pads as they could cause damage to the product’s surface.

The technical specifications for the CECOTEC READY WARM 800 THERMAL are: