CECOTEC READY WARM 800 THERMAL BLACK (01) PDF Document

Allow the CECOTEC READY WARM 800 THERMAL BLACK to operate at maximum temperature for 2-3 hours in a ventilated place in order to eliminate all manufacturing wastes.

Place the stand on the bottom part of the CECOTEC READY WARM 800 THERMAL BLACK, each one on one side, and screw them. Make sure they are properly fixed.

1. Before installing the CECOTEC READY WARM 800 THERMAL BLACK, make sure the appliance is placed at a minimum safety distance of 20 cm from any obstacle (walls, shelves, floor…).

2. Drill 2 holes on the wall with 140 mm between them.

3. Attach the wall supports to the wall using the studs and screws provided.

4. Make sure the smaller-diameter side of the supports is hung from the wall.

5. Screw the wall support accessory onto the 2 holes on the back-bottom part of the CECOTEC READY WARM 800 THERMAL BLACK. Make sure the side with just 1 hole is against the wall.

6. Hang the appliance from the support.

7. Once hung on the wall, mark the free hole of the wall support accessory.

8. Remove the appliance from the wall, drill a hole where the mark is and introduce the corresponding stud.

9. Finally, hang the appliance on the brackets and screw the mounting plate to the wall.

The buttons on the device’s control panel will block if no button is pressed for 1 minute during operation.

To unlock it, press (-) for 3 seconds.

The CECOTEC READY WARM 800 THERMAL BLACK has 3 operating modes in manual mode:

Day mode: The temperature can be adjusted from 5 °C to 35 °C.

Sleep mode: The temperature can be adjusted from 5 °C to 35 °C.

Anti-frost mode: The temperature can be adjusted from 5 °C to 15 °C.

For the CECOTEC READY WARM 800 THERMAL BLACK to operate correctly, the set temperature must always be higher than the room temperature. The panel will display the room temperature. When setting the desired temperature, select a few more degrees than desired ones, as the temperature shown on the display is the one next to the device and not the real room one.

1. Connect the CECOTEC READY WARM 800 THERMAL BLACK to a power supply and turn the power switch on.

2. The control panel will flash and the “°C” symbol, room temperature and power indicator will light up. If this last symbol does not light up, press it.

3. Select the desired operating mode by pressing the corresponding button: Day, Sleep or Anti-frost. The display will show the selected mode.

4. Use the + and – buttons to set the desired temperature for the selected mode. During the temperature setting, the “°C” icon will blink.

5. Once the desired temperature has been set, the display will show the room temperature again.

6. Repeat the above steps to set the temperature for the other modes.

7. Use the on/off button to turn the heater on and off.

When the CECOTEC READY WARM 800 THERMAL BLACK reaches the set temperature, it will automatically switch off and the icon will turn off.

When the room temperature falls below the set one, the device will automatically turn back on and the icon will light up again.

To reset the CECOTEC READY WARM 800 THERMAL BLACK while it is connected to the power supply and the power switch is on, make sure the device is unlocked or unlock it with the remote control and press the power button (-) for 3 seconds. It can also be switched off and on.

1. Long press the “PROG” button until the display shows “00:00”.

2. The hour digits will blink. Use the + and – buttons to set the desired hour and press “PROG” to save the settings.

3. The minutes digits will blink. Use the + and – buttons to set the desired minutes and press “PROG” to save the settings.

4. The display will show the week calendar (Monday-Sunday, 1-7). Select the current day by pressing + and -. Press “PROG” to save the settings.

1. The display will show the first 2 bars for the first period of time (00:00 – 1:00 am) blinking. It will also show 1 as Monday.

2. Press the desired mode (Day, Sleep or Anti-frost) for the selected time interval.

If you select Sleep mode, the display will show an icon and the bar on the top part will blink.

If you select the Anti-frost mode, the display will show an icon and the bar on the lower part will blink.

If you select Day mode, the display will show an icon and the top and lower bars will blink.

3. Once the first period has been scheduled, press “+” and the next time period’s bars will blink.

4. Repeat these steps up to 24 hours.

5. When all the hours in a day have been scheduled, press “PROG” to end the selected day scheduling and repeat the steps to schedule the 7 days of the week.

6. Once the whole week has been scheduled, press “PROG” and the device will automatically save the settings and operate in the set mode.

If the CECOTEC READY WARM 800 THERMAL BLACK is disconnected from the power supply, the schedule settings will be saved but the current day and time will be reset.

If the CECOTEC READY WARM 800 THERMAL BLACK is operating under programmed mode, to change it:

1. Press the on button on the remote control twice.

2. Press “PROG”.

3. Select the desired mode and adjust the temperature if necessary, using the + and -buttons.

1. During operation, press twice the on button on the remote control and use the + and – buttons to select the desired temperature.

2. Once the temperature is set, it will be saved for this mode for future operations, including under manual mode.

Turn off, unplug the CECOTEC READY WARM 800 THERMAL BLACK from the power supply and allow it cool down before cleaning it.

Use a soft, dry and clean cloth to clean the product’s outer housing.

Do not use abrasive cleaners or scouring pads as they could cause damage to the product’s surface.

Product reference: 05330, 05892

Product: ReadyWarm 800 Thermal / ReadyWarm 800 Thermal Black

Power and voltage: 600 W, 220-240 V, 50/60 Hz

Made in China | Designed in Spain