CAMRY CR 4623 (01) PDF Document

The following safety conditions must be followed when using the CAMRY CR 4623:

1. The product is only to be used indoors and for its intended household application. Any misuse may result in damage for which the manufacturer is not responsible.

2. The applicable voltage is 220-240V ~50/60Hz. It is not appropriate to connect multiple devices to one power outlet.

3. Do not immerse the motor unit, power cable, or plug in water or any other liquids.

4. Never use the device if it has been dropped, damaged, or has a damaged power cable. Do not attempt to repair it yourself; instead, turn it over to a professional service location.

5. The blades are very sharp. Use extreme care when handling them and always keep fingers away from moving parts.

6. Never blend hot oil or fat. Do not process ingredients hotter than 80 degrees Celsius (175 degrees Fahrenheit) in the beaker, chopper bowl, or food processor bowl.

7. Do not process frozen food or fruits containing stones or pips.

8. Never blend bones, ice, coffee, or peanuts with the blender attachments.

9. Short-time operating: Use the appliance for no longer than 60 seconds at a time. Leave it to cool down completely for at least 1 minute before using it again.

10. If the handle becomes hot (hotter than 50 degrees Celsius), unplug the appliance and let it cool for at least 60 minutes.

The CAMRY CR 4623 includes the following components as shown in the product description:

The technical data for the CAMRY CR 4623 is listed below:

Step 1. Clean the device before the first use.

Step 2. Allow any hot ingredients to cool down before processing them with the appliance.

Step 3. If using the hand blender or chopper, cut large ingredients into cubes approximately 2cm in size. If using the food processor discs or cube cutter, cut ingredients into pieces that fit through the inlet lid hole.

Step 4. Ensure the appliance is assembled properly for the specific task intended.

Step 5. Switch off and disconnect the appliance from the mains before assembly, disassembly, storage, or cleaning.

The CAMRY CR 4623 features dual speed control options:

1. Variable Speed: Press the speed button “-” to process food while using the variable speed regulator. Manipulating the regulator allows you to adjust the speed; higher settings result in faster and finer chopping.

2. Maximum Speed: Press the speed button “=” to operate the appliance at its maximum speed. When this button is used, the variable speed regulator cannot be adjusted.

Step 1. Attach the blender shaft to the motor unit until you hear a click.

Step 2. Immerse the blade guard completely into the ingredients to avoid splashing.

Step 3. Press the speed button to switch the appliance on.

Step 4. Move the appliance slowly up and down and in circles to blend the ingredients.

Step 5. If blending directly in a saucepan while cooking, remove the pan from the stove first to protect the unit from overheating.

Step 1. Put the chopper blade unit into the chopper bowl.

Step 2. Place your ingredients into the chopper bowl. Pre-cut meat, cheese, onions, or garlic and remove any stalks, shells, bones, tendons, or gristle first.

Step 3. Place the coupling unit onto the chopper bowl.

Step 4. Fasten the motor unit onto the chopper bowl assembly.

Step 5. Press the normal or turbo speed button to switch the appliance on.

Step 1. Insert the whisk into the whisk coupling unit.

Step 2. Connect the coupling unit to the motor unit.

Step 3. Put ingredients into a large, deep bowl for the best results.

Step 4. Immerse the whisk completely into the ingredients. To avoid splashing, start processing at a low speed.

Step 1. Place the blade support on the center pin of the bowl, place the desired disc into the support, and turn it to lock it into place.

Step 2. Attach the food processor lid onto the bowl and turn it clockwise to lock.

Step 3. Insert the motor unit into the coupling unit until it locks.

Step 4. Fill the food into the filling tube. Use only the pusher to feed ingredients in; never reach into the tube while the appliance is switched on.

Step 5. Press the speed button to switch the appliance on.

Step 1. Open the 4 metal buckles on the cubic cutter support.

Step 2. Insert the selected cutting grill into the hole of the cubic cutter support, apply the blade, and close the 4 metal buckles.

Step 3. Place the cubic cutter support on the bowl, aligning the four notches with the four hooks on the inside edge of the bowl. Ensure it is in a horizontal position.

Step 4. Put the lid on the bowl and turn to fix it. Fasten the motor unit onto the lid.

Step 5. Put ingredients into the feeding tube. Pre-cut them into chunks that fit loosely. For large amounts, process in batches of maximum 250g and empty the bowl after processing 500g.

Step 6. Press and hold the speed button. Use the pusher lightly to feed ingredients through.

Step 7. After processing, press the release button to remove the motor unit, then turn the lid anticlockwise to remove it and empty the bowl.

Step 1. Cook the vegetables (such as potatoes, swede, or carrots) and drain them. Do not mash hard or uncooked foods as this may damage the unit.

Step 2. Fit the masher coupling unit to the masher foot by turning it in an anticlockwise direction.

Step 3. Turn the masher upside down and fit the paddle into the central hub, turning it anticlockwise to fix it.

Step 4. Fit the motor unit to the assembled masher kit.

Step 5. Plug the device in and move the masher through the vegetables until the desired result is achieved.

Step 6. After use, release the speed button and unplug. Remove the paddle by turning it clockwise and unscrew the coupling unit from the masher foot.

Step 7. Never use the masher in a saucepan over direct heat; always remove the pan from heat first.

Step 1. Always remove the accessories and unplug the device before cleaning.

Step 2. The motor unit, chopper lid, processor lid, and coupling units must only be cleaned with a moist cloth. Do not immerse these parts in water or rinse them under the tap.

Step 3. Clean the beaker, processor bowl, chopper blade, chopper bowl, cubic cutter support, grills, and discs in warm water with washing-up liquid.

Step 4. The blade shaft and the whisk can be cleaned while still attached to the motor unit by immersing them in warm water with washing-up liquid and running the appliance briefly.

Step 5. Never use scouring pads, abrasive cleaning agents, or aggressive liquids like petrol or acetone to clean the appliance.