BMW 328I CONVERTIBLE 2008 (01) PDF Document

The owner’s manual for your BMW 328I CONVERTIBLE 2008 uses several symbols to convey important information:

Warning Triangle: Indicates precautions that must be followed precisely to avoid personal injury and serious damage to the vehicle.

Information Icon: Indicates information that will assist you in gaining the optimum benefit from your vehicle and enable you to care for it more effectively.

Environment Icon: Refers to measures that can be taken to help protect the environment.

* (Asterisk): Indicates special equipment, country-specific equipment, optional extras, or equipment and functions not yet available at the time of printing.

“…” (Quotation Marks): Identifies Control Display texts used to select individual functions.

{…} (Curly Brackets): Identifies verbal instructions to use with the voice command system.

{{…}} (Double Curly Brackets): Identifies the answers generated by the voice command system.

Book with “i” Icon: Indicates that you should consult the relevant section of the Owner’s Manual for information on a particular part or assembly.

The buttons on the steering wheel of your BMW 328I CONVERTIBLE 2008 perform the following functions:

Telephone Functions:

Press: Accept and end a call, start dialing a selected phone number, or redial if no number is selected.

Press longer: Redialing.

Audio and Navigation Functions:

Volume: Adjust the volume of audio sources.

Arrow Buttons: Change the radio station or select a music track.

Thumbwheel: Scroll through the phone book and lists with stored phone numbers.

Programmable Buttons (Star and Diamond symbols): These buttons are individually programmable to perform specific functions. You can assign functions to them via the iDrive system.

Cruise Control Buttons:

These buttons are used to operate the Cruise Control or Active Cruise Control systems.

The following indicator lamps on your BMW 328I CONVERTIBLE 2008 notify you that certain functions are active without accompanying text messages:

High beams/headlamp flasher: Indicates that the high beams are on.

Fog lamps: Indicates that the fog lamps are active.

DSC or DTC lamp (flashing): Flashes when the Dynamic Stability Control or Dynamic Traction Control is regulating the propulsive forces to maintain driving stability.

BRAKE (Red): Indicates that the parking brake is applied.

(!) (Red, for Canadian models): Indicates that the parking brake is applied.

SERVICE ENGINE SOON: Indicates an engine malfunction with an adverse effect on exhaust emissions.

The iDrive system in your BMW 328I CONVERTIBLE 2008 integrates the functions of many switches into a single central controller. Operate the controller only when traffic and road conditions allow.

The iDrive system consists of:

1. Control Display: The screen where menus and information are shown.

2. MENU button: Opens the start menu.

3. Controller: Used to select menu items and adjust settings.

To operate the controller:

Move in four directions: Push the controller forward, backward, left, or right to navigate through menus.

Turn: Rotate the controller to scroll through lists or adjust settings.

Push: Press down on the controller to select a highlighted item or confirm a setting.

To navigate the iDrive system in your BMW 328I CONVERTIBLE 2008, follow these general steps:

1. Selecting a menu item:

Turn the controller to move the highlight marker through the menu items.

Menu items shown in white can be selected.

2. Activating a menu item:

Press the controller to select the highlighted item.

This will either display new menu items or execute the selected function.

3. Switching between fields:

Briefly move the controller to the left, right, forward, or backward to move between different fields or columns on the screen.

Release the controller. The active field will be brighter in color.

4. Adjusting settings:

Turn the controller to change settings like numerical values, graphic displays, or text options.

Confirm the change by moving to a different field.

Your BMW 328I CONVERTIBLE 2008 is equipped with programmable memory keys that allow you to store and quickly execute certain iDrive functions. The assignments are stored for the remote control currently in use.

Functions you can store:

– Navigation destinations

– Entertainment sources (Radio stations, CD, CD changer compartment, AUX)

– Telephone numbers

Storing a Function:

1. In the iDrive menu, select the function you wish to store (e.g., a specific radio station or a navigation destination).

2. Press and hold one of the programmable memory keys (numbered 1-6) for more than 2 seconds.

Executing a Stored Function:

Briefly press the desired memory key. The stored function will be executed immediately (e.g., the radio tunes to the stored station, or destination guidance begins).

Displaying Memory Key Assignments:

To see what function is stored on a key, lightly touch the key with your finger without pressing it. The stored assignment will be displayed at the top of the Control Display. Do not wear gloves, as the keys are touch-sensitive.

To clear all stored functions from the programmable memory keys in your BMW 328I CONVERTIBLE 2008, follow these steps using the iDrive system:

1. Press the MENU button to open the start menu.

2. Press the controller to open the “i” menu.

3. Select “Settings” and press the controller.

4. Select “Vehicle / Tires” and press the controller.

5. Select “Programmable Memory Keys” and press the controller.

6. Select “Delete assignment of all memory keys” and press the controller.

7. Select “Yes” and press the controller to confirm.

The voice command system allows you to control many vehicle functions without taking your hands off the steering wheel. For best performance, keep doors, windows, and the glass roof closed to reduce ambient noise.

Activating the Voice Command System:

1. Press the voice command button on the steering wheel.

2. A symbol will appear on the Control Display and an acoustic signal will sound, indicating the system is ready for a command.

3. Say the command. The command will appear on the Control Display.

Basic Voice Command Tips:

Pronounce commands and digits smoothly and at a normal volume, avoiding pauses or excessive emphasis.

Always speak the commands in the language selected for the iDrive system.

Say {Help} to have the system provide instructions.

Say {Cancel} or press the voice command button to terminate or cancel the operation.

Short commands can be used to perform functions immediately, regardless of the current menu. For example, say {Radio on}.

The remote control for your BMW 328I CONVERTIBLE 2008 can perform several functions related to opening and closing the vehicle.

Unlocking:

Press the unlock button. The interior lamps and welcome lamps will switch on. You can configure the system via iDrive to unlock either only the driver’s door or all doors on the first press.

Locking:

Press the lock button. This locks the doors, luggage compartment lid, and fuel filler door, and arms the anti-theft system.

Convenient Opening (Retractable Hardtop):

Within a range of approx. 13 ft/4 m, press and hold the unlock button. The windows will lower and the retractable hardtop will open. Releasing the button interrupts the process. If you continue pressing after the top is open, the windows will move up.

Convenient Closing (Retractable Hardtop):

Within a range of approx. 13 ft/4 m, press and hold the lock button. The retractable hardtop and the windows will close. Releasing the button interrupts the process. Always watch to ensure no one is injured during closing.

Unlocking the Luggage Compartment Lid:

Press and hold the luggage compartment button for approx. 1 second. The lid will open slightly.

Switching on Interior Lamps:

While the car is locked, press the lock button to briefly switch on the interior lights, for example, to locate your vehicle in a parking garage.

You can customize how the central locking system on your BMW 328I CONVERTIBLE 2008 behaves using the iDrive system. The settings are stored for the remote control currently in use.

Setting what the unlock button does:

1. Press the MENU button.

2. Press the controller to open the “i” menu.

3. Select “Settings” and press the controller.

4. Select “Vehicle / Tires” and press the controller.

5. Navigate to and select “Door locks”.

6. Select “Central locking” and press the controller.

7. Select “Unlock button” and press the controller.

8. Choose between “All doors” (unlocks the entire vehicle with one press) or “Driver’s door only” (unlocks only the driver’s door and fuel filler door with one press; a second press unlocks the rest of the vehicle).

Setting automatic locking:

1. Follow steps 1-6 above.

2. Select a menu item:

– “Relock door if not opened”: The vehicle automatically locks itself after a short time if no door has been opened after unlocking.

– “Lock after driving”: The vehicle automatically locks itself as soon as you start driving off.

3. Press the controller to activate the selected setting.

The alarm system on your BMW 328I CONVERTIBLE 2008 is armed and disarmed automatically when you lock or unlock the vehicle with the remote control or the door lock.

The alarm system responds to:

– A door, the hood, or the luggage compartment lid being opened.

– Movements inside the vehicle (interior motion sensor).

– Changes in the car’s inclination, such as an attempt to jack it up or tow it away (tilt alarm sensor).

– Interruption of power supply from the battery.

When triggered, the alarm system activates an acoustic alarm, the hazard warning flashers, and the high beams for a short time.

Indicator Lamp:

The indicator lamp under the interior rearview mirror flashes continuously when the system is armed. If it flashes for 10 seconds after locking and then becomes continuous, it indicates that a door, the hood, or the luggage lid is not properly closed.

Switching Off an Alarm:

Unlock the car with the remote control or insert the remote control all the way into the ignition lock.

Avoiding Unintentional Alarms:

To prevent unintentional alarms (e.g., when transporting the vehicle or leaving animals inside), you can temporarily switch off the tilt alarm and interior motion sensors. To do this, press the lock button on the remote control a second time immediately after locking the vehicle.

The convenient access system on your BMW 328I CONVERTIBLE 2008 allows you to unlock, lock, and start the vehicle without holding the remote control in your hand, as long as it is close to your body (e.g., in a pocket).

Unlocking the Vehicle:

Grasp the handle on the driver’s or front passenger’s door completely. This unlocks the vehicle.

Locking the Vehicle:

Touch the ridged surface on the outside of the door handle with your finger for approximately 1 second. This locks the vehicle and arms the alarm system.

Unlocking the Luggage Compartment:

Press the button on the outside of the luggage compartment lid.

Starting the Engine:

With the remote control inside the vehicle, you can start the engine by depressing the brake pedal and pressing the Start/Stop button. It is not necessary to insert the remote control into the ignition switch.

Switching Off the Engine (Automatic Transmission):

The engine can only be switched off when the selector lever is in position P.

Malfunction:

If convenient access malfunctions due to local radio waves, use the buttons on the remote control or the integrated key to open/close the vehicle. To start the engine, insert the remote control into the ignition switch.

If the indicator lamp in the instrument cluster comes on with a message to replace the battery, follow these steps for your convenient access remote control:

1. Take the integrated key out of the remote control by pressing the release button.

2. Use the key or a small tool to carefully pry off the battery cover on the back of the remote.

3. Remove the old battery.

4. Insert the new battery with the positive (+) side facing up.

5. Press the cover back on until it clicks into place.

To operate the retractable hardtop on your BMW 328I CONVERTIBLE 2008, the vehicle must be stationary. For battery conservation, it is best to operate it with the engine running.

Before Operating:

– Ensure there is sufficient clearance above and behind the vehicle.

– Ensure the cargo bay partition is folded down and engaged on both sides.

– Ensure no objects are placed on or next to the cargo bay partition or on the hardtop itself.

– Ensure the luggage compartment lid is closed.

Opening and Closing the Hardtop:

Use the switch located in the center console.

To Open: Pull and hold the switch. The sequence of movements is automatic. Releasing the switch will interrupt the process.

To Close: Push and hold the switch. The sequence of movements is automatic. Releasing the switch will interrupt the process.

The left LED on the switch lights up green during operation and goes out when the top is fully opened or closed. If the right LED flashes red when you release the switch, the operation is not yet complete. If the right LED lights up red when the switch is pressed, there is a malfunction or a prerequisite is not met (e.g., cargo partition is up).

The wind deflector minimizes air movement in the passenger compartment when the hardtop is open. It is stored in a protective cover in the cargo bay.

Installation:

1. Remove the wind deflector from its cover and unfold it.

2. Press the top and bottom parts of the deflector together until the catch engages.

3. Push the fastening pin on the right side of the deflector into the corresponding opening in the vehicle’s side trim until it snaps into place.

4. Push the fastening pin on the left side into its opening until it snaps into place.

5. Turn the rotary handle as far as the first stop to insert the right fastening pin into its holders.

6. Turn the rotary handle further to the next symbol to insert the left fastening pin into its holders.

7. Fold up the top section of the wind deflector.

Using the Loading Function:

To load cargo onto the rear seat with the deflector installed:

1. Lower all windows.

2. Fold down the top section of the wind deflector.

3. Turn the rotary handle to the unlocked position.

4. Fold both sections of the deflector forward against the front seats.

Removing the Wind Deflector:

Proceed in the reverse order of installation.

The memory function allows you to store and recall two different driver’s seat and exterior mirror positions.

Storing Positions:

1. Switch on the radio readiness or the ignition.

2. Adjust the driver’s seat and exterior mirrors to your desired positions.

3. Press the “M” (Memory) button on the side of the driver’s seat. The LED in the button will light up.

4. Within a few seconds, press the desired memory button (1 or 2). The LED will go out, and the positions are now stored.

Calling Up Stored Positions:

Convenience Mode: With the driver’s door open or radio readiness switched on, briefly press the desired memory button (1 or 2). The seat and mirrors will move to the stored position. The process stops if you touch a seat adjustment switch.

Safety Feature: With the driver’s door closed and ignition on or off, press and hold the desired memory button (1 or 2) until the adjustment process is complete.

Automatic Call-up with Remote Control:

The last used seat position is automatically stored for the remote control in use. You can set the system via iDrive to automatically move the seat to this stored position when the vehicle is unlocked or when the driver’s door is opened.

Your BMW 328I CONVERTIBLE 2008 is equipped with the LATCH (Lower Anchors and Tethers for CHildren) system for securing compatible child-restraint systems. Always follow the child-restraint system manufacturer’s instructions.

Using the Lower Anchors:

1. Locate the lower LATCH anchor points in the rear seats. They are positioned behind labeled protective caps between the seat cushion and the backrest.

2. Attach the lower connectors of the child-restraint system to the LATCH anchors.

3. Ensure both connectors are correctly engaged and that the child-restraint system rests firmly against the seat backrest.

To Lock the Safety Belt for Non-LATCH Seats:

If you are securing a child seat with the vehicle’s safety belt, you can lock the retractor to hold the seat firmly.

1. Secure the child-restraint system with the safety belt.

2. Pull the belt strap all the way out of the retractor.

3. Allow the belt strap to retract. As it retracts, you will hear a ratcheting sound, indicating the retractor is locked. Pull it taut against the child-restraint system.

To unlock the safety belt, unbuckle it and allow the strap to retract all the way.

The Steptronic automatic transmission in your BMW 328I CONVERTIBLE 2008 can be operated in fully automatic mode or shifted manually.

Selector Lever Positions:

P (Park): Select only when the vehicle is stationary. The rear wheels are locked.

R (Reverse): Select only when the vehicle is stationary.

N (Neutral): Idle position. The vehicle can roll.

D (Drive): The position for normal, fully automatic driving. All forward gears are selected automatically.

Sport Program and Manual Operation (M/S):

1. From position D, move the selector lever to the left into the M/S gate.

2. The sport program is activated, indicated by “DS” in the instrument cluster. This mode provides a more performance-oriented driving style with faster gear changes at higher RPMs.

3. To shift manually, push the lever forward for a downshift (-) or pull it back for an upshift (+). The current gear (M1 to M6) is displayed in the instrument cluster.

4. To return to fully automatic mode (D), move the selector lever back to the right.

Kick-down:

For maximum acceleration in position D, press the accelerator pedal beyond the full-throttle resistance point. The transmission will shift down to the lowest possible gear.

The cruise control system on your BMW 328I CONVERTIBLE 2008 can be used at speeds above approx. 20 mph (30 km/h).

Activating and Storing Speed:

Briefly push the lever on the steering column forward (arrow 1) or pull it backward (arrow 2). The current speed is stored and maintained.

Increasing Speed:

Repeatedly press the lever forward (arrow 1) until the desired speed is reached. Each brief press increases the speed by approx. 1 mph. Pressing beyond the resistance point increases speed in increments of up to 5 mph.

Decreasing Speed:

Repeatedly pull the lever backward (arrow 2) until the desired speed is reached. Each brief pull decreases speed by approx. 1 mph. Pulling beyond the resistance point decreases speed in increments of up to 5 mph.

Deactivating Cruise Control:

Tap the lever upwards or downwards (arrow 3), or apply the brakes. The system also deactivates if you select neutral or if the DSC system intervenes.

Resuming Stored Speed:

Press the button on the end of the lever (arrow 4). The system will resume the last stored speed.

The Park Distance Control (PDC) system in your BMW 328I CONVERTIBLE 2008 assists with maneuvering by using ultrasonic sensors in the bumpers to detect obstacles.

Activation:

The system switches on automatically when you engage reverse gear (R) with the engine running or ignition on.

How it Works:

As you approach an obstacle, the system emits an intermittent acoustic signal. The interval between the tones becomes shorter as you get closer to the object. When the distance is less than roughly 1 ft (30 cm), the tone becomes continuous.

Visual Warning (via iDrive):

You can activate a visual display on the Control Display to supplement the acoustic warnings. This shows the contours of objects as they are detected by the sensors. To activate this display:

1. Go to the iDrive “Settings” menu.

2. Select “Vehicle / Tires”.

3. Select “PDC”.

4. Select “PDC display on” and press the controller.

Malfunction:

If the indicator lamp in the instrument cluster comes on and a message appears on the Control Display, the PDC system is malfunctioning. Keep the sensors clean and free of ice or snow for proper operation.

Dynamic Traction Control (DTC) is a function of the Dynamic Stability Control (DSC) system in your BMW 328I CONVERTIBLE 2008. When activated, DTC optimizes drive output and traction but with reduced driving stability.

When to Activate DTC:

It is useful to briefly activate DTC in the following special circumstances to allow for more wheel spin:

– When driving on snow-covered roads, in slush, or on unplowed roads.

– When trying to rock a stuck vehicle free or starting off in deep snow or on loose ground.

– When driving with snow chains.

How to Activate/Deactivate DTC:

Activate: Briefly press the DTC button on the center console. The indicator lamps for DTC in the instrument cluster will come on.

Deactivate: Press the DTC button again. The DTC indicator lamps in the instrument cluster will go out.

To fully deactivate both DSC and DTC for maximum drive-output with no stabilizing interventions, press and hold the DTC button for at least 3 seconds. The indicator lamp for DSC will light up in the instrument cluster.

The Flat Tire Monitor (FTM) must be reinitialized each time you correct the tire inflation pressure or change a wheel or tire to ensure reliable reporting. Do not initialize the system while snow chains are attached.

Using iDrive to Initialize FTM:

1. Start the engine, but do not start driving.

2. Press the MENU button to open the start menu.

3. Press the controller to open the “i” menu.

4. Select “Settings” and press the controller.

5. Select “Vehicle / Tires” and press the controller.

6. Navigate to and select “FTM”.

7. Select “Reset” and press the controller.

8. Select “Yes” and press the controller to confirm.

9. Start to drive. Initialization is completed automatically while the car is moving.

If the warning lamps for the Flat Tire Monitor come on in yellow and red, accompanied by an acoustic signal, there is a flat tire or substantial loss of pressure. Your vehicle is equipped with Run-Flat Tires, which allow for continued driving under certain restrictions.

1. Cautiously reduce your speed to below 50 mph (80 km/h).

2. Avoid sudden braking and steering maneuvers.

3. In the event of complete pressure loss (0 psi), you can estimate the possible distance for continued driving based on the following guidelines:

– Light load (1-2 persons, no luggage): approx. 155 miles/250 km

– Medium load (2 persons, full cargo bay, or 4 persons, no luggage): approx. 90 miles/150 km

– Full load or towing: approx. 30 miles/50 km

Drive cautiously as vehicle handling will be affected (reduced stability, extended braking distance). If you notice unusual vibrations or loud noises, the tire may have failed completely. Pull over as soon as it is safe to do so and contact your BMW center.

You can set the time and date using either the instrument cluster controls or the iDrive system.

Using the Instrument Cluster:

1. Use the button on the turn indicator lever to scroll until the time or date symbol appears with the word “SET”.

2. Press the button on the end of the lever to enter setting mode.

3. Use the up/down function of the lever button to adjust the value (hours, minutes, day, month, year).

4. Press the end button to confirm each entry and move to the next.

Using iDrive:

1. Open the iDrive start menu and go to “Settings”.

2. Select “Time / Date”.

3. Select “Time” or “Date”.

4. Select “Set time” or “Set date”.

5. Turn the controller to adjust the highlighted value (hours, minutes, etc.).

6. Press the controller to confirm and move to the next value.

7. The system accepts the new setting after the final confirmation.

The automatic climate control system maintains your desired interior temperature.

AUTO Program:

Press the AUTO button for the most effective and comfortable climate control. The system will automatically regulate air distribution, air flow rate, and temperature. You can adjust the intensity of the AUTO program by pressing the button repeatedly.

Temperature:

Turn the knobs on the left and right to set the desired temperatures for the driver’s and front passenger’s sides individually.

Manual Air Distribution:

Press the buttons with arrows pointing to the windshield, the upper body, or the footwell to manually direct airflow. This deactivates the automatic air distribution of the AUTO program.

Manual Air Flow Rate:

Press the left or right side of the fan button to decrease or increase the blower speed manually.

Defrosting Windows:

Press the button with the windshield and fan symbol to quickly remove ice or condensation from the windshield and front side windows.

Recirculated-Air Mode:

Press the button with the car and circular arrow symbol repeatedly to cycle through modes: outside air, Automatic Recirculated-air Control (AUC – automatically blocks polluted outside air), and permanent recirculated air.

Convertible Program:

When the hardtop is open, a “Convertible” program becomes available in the iDrive climate settings. This program optimizes climate control for open-top driving.

The integrated universal remote control can be programmed to operate up to three devices like garage doors or gates.

Clearing Existing Programming (First Time Use):

Press and hold the two outer memory buttons for approx. 20 seconds until the LED flashes rapidly. This clears all three buttons.

Programming a Fixed-Code Transmitter:

1. Switch on the ignition.

2. Hold your original hand-held transmitter 4 to 12 inches away from the memory buttons in the vehicle.

3. Simultaneously press and hold the transmit button on your original remote and the desired memory button (1, 2, or 3) in the vehicle.

4. The LED in the vehicle will flash slowly at first. When it begins to flash rapidly, release both buttons. The programming is complete.

Programming an Alternating-Code (Rolling Code) Transmitter:

1. Follow all the steps above for programming a fixed-code transmitter.

2. Locate the “learn” or “program” button on the receiver of the device you want to control (e.g., the garage door opener motor unit).

3. Press this “learn” button. You will then have approx. 30 seconds to complete the next step.

4. Return to your vehicle and press the programmed memory button three times.

You can enter a destination in your BMW 328I CONVERTIBLE 2008 manually via the iDrive controller.

1. Press the MENU button, then move the controller to the right to select “Navigation”.

2. “New destination” will be highlighted. Press the controller.

3. Select “Enter address” and press the controller.

4. Select Country/State: Select “State / Province” and choose the correct location from the list.

5. Enter Town/City or Zip Code: Select “Town / City”. You can either enter the name letter by letter or enter a zip code. The system’s word-matching principle will suggest names as you type.

6. Enter Street: Select “Street” and enter the street name letter by letter.

7. Enter House Number: Select “House number” and enter the number.

8. After the address is complete, you can select “Start guidance” to begin the route immediately or “Add to destination list” to save it for later.

You can control the radio in your BMW 328I CONVERTIBLE 2008 using the buttons on the center console or the iDrive system.

Switching On/Off and Adjusting Volume:

Press the volume knob on the center console to switch the audio on or off. Turn the knob to adjust the volume.

Selecting a Waveband (AM/FM):

1. In the iDrive system, move the controller backwards from the start menu to select “Entertainment”.

2. Select “FM” or “AM”.

Changing Stations:

Using the Controller: Turn the controller to scroll through the list of available or preset stations.

Using Console Buttons: Press the arrow buttons next to the CD slot to move to the next station in the list.

Scan: In the “Set” menu for the selected waveband, choose “Scan” to sample available stations. Press the controller again to stop on a station.

Storing Stations:

1. Tune to the desired station.

2. In the iDrive “Set” menu, select “Store”.

3. Turn the controller to select a memory location in the “Presets” list.

4. Press the controller to store the station.

Alternatively, you can press and hold one of the programmable memory keys for a longer period to store the currently tuned station.

The CD player and optional CD changer in your BMW 328I CONVERTIBLE 2008 can play standard audio CDs and CDs with compressed audio files like MP3s.

Playing a CD in the Head Unit Player:

1. Insert a CD into the upper slot in the center console with the label side up. The CD will be pulled in automatically.

2. Playback will start automatically if the audio system is switched on.

Playing a CD in the CD Changer:

1. If not already selected, go to the iDrive “Entertainment” menu and select “CD”.

2. Move the highlight to the second field from the top (which shows the different CD slots) and select the desired CD (e.g., CD 1, CD 2, etc.). Playback will begin.

Selecting a Track:

Using iDrive: Turn the controller to scroll through the track list and press to select a track.

Using Console Buttons: Press the arrow buttons next to the CD slot to skip to the next or previous track.

Functions like Random Play and Repeat:

In the “CD” menu, press the controller and select “Set” to access options like “Random” (random play) and “Repeat” (repeat track).

To use your mobile phone with the hands-free system, you must first pair it with the vehicle. The process must be done while the car is stationary.

Preparation:

– Ensure your mobile phone is compatible and its Bluetooth function is turned on and discoverable.

– Decide on a Bluetooth passkey (e.g., 1234). You will need to enter this on both the phone and the iDrive system.

Pairing via iDrive:

1. Switch on the ignition in your BMW.

2. Press the MENU button, then the controller to open the “i” menu.

3. Select “Settings” > “Bluetooth”.

4. In the second field, select “Phone” and press the controller.

5. Select “Pair new phone” and press the controller.

6. Select “Start pairing” and press the controller. The Bluetooth name of your vehicle will be displayed (e.g., BMW 76002).

On Your Mobile Phone:

7. Use your mobile phone to search for Bluetooth devices. Select the Bluetooth name of your BMW from the list on your phone.

Completing the Pairing:

8. You will be prompted to enter the Bluetooth passkey. Enter the same passkey on your mobile phone and in the iDrive system using the controller.

9. On the iDrive screen, select “Confirm passkey” and press the controller.

10. After a few seconds, the “Communication” menu should appear, indicating that the pairing was successful.

If your vehicle’s battery is flat, you can use jumper cables and another vehicle’s battery to start the engine. Always connect the cables in the correct order to prevent injury and damage.

Preparation:

1. Ensure the assisting vehicle has a 12-volt battery.

2. Switch off the engines and any electrical consumers in both vehicles.

3. Make sure the vehicle bodies do not touch.

Connecting Jumper Cables:

1. Open the hood. Locate the jump-starting connection terminal in the engine compartment. It has a cap marked with a “+” symbol. Pull the cap up to remove it.

2. Attach one clamp of the positive (+) jumper cable to the positive terminal of the assisting vehicle’s battery.

3. Attach the other clamp of the positive (+) jumper cable to the positive jump-starting terminal of your BMW.

4. Attach one clamp of the negative (-) jumper cable to the negative terminal of the assisting vehicle’s battery.

5. Attach the other clamp of the negative (-) jumper cable to the specified ground point (a special nut) on your BMW’s engine block, away from the battery.

Starting the Engine:

1. Start the engine of the assisting vehicle and let it run for a few minutes.

2. Start the engine of your BMW in the usual way.

3. Let both engines run for a few minutes.

Disconnecting Jumper Cables:

Disconnect the cables in the exact reverse order of connection.

When towing is necessary, there are specific procedures to follow for your BMW 328I CONVERTIBLE 2008 to prevent damage.

Using the Screw-in Tow Fitting:

The screw-in tow fitting is stored in the onboard tool kit under the cargo bay floor panel. It can be screwed into threaded openings at the front or rear of the vehicle, located behind small cover panels in the bumper.

Towing Preparation:

Switch on the ignition to ensure brake lights, turn signals, and wipers are functional. Power steering will not work without the engine running, so more effort is required.

For Vehicles with Automatic Transmission:

The selector lever must be in position N. Do not exceed a towing speed of 45 mph (70 km/h) or a towing distance of 90 miles (150 km), otherwise the transmission may be damaged.

Towing Methods:

It is recommended that your BMW be transported on a flatbed tow truck. Do not tow the vehicle with just the rear axle raised, as this may cause the steering to turn. Do not lift the vehicle by a tow fitting or body parts.

Note: All pressure specifications are for cold tires (ambient temperature).