Click here to download AUDIOVOX ELECTRONICS PURSUIT 093BPR (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** Model 093BPr Transmitter Programming Guide These transmitters make use of icons (symbols) to identify the reaction your security system/keyless entry/and or remote start system, where applicable, will have when any icon (button) is pressed. These icons are programmed at time of installation to meet the needs of the individual and to complement the vehicle that the system is installed in. To replace a transmitter or add transmitters, please follow the programming instructions listed on the pages of this manual. BUTTON O OPT. 1 OPT-2 * Where So Equipped RECEIVER CHANNEL 1 2 1 3 *4 *5 SYSTEM FUNCTION Lock And Arm Alarm, also initiate and terminates *Panic Unlock And Disarm, also initiates and terminates *Panic. Programmable to unlock drivers door and or all doors. Lock and arm/unlock and disarm. May be programmed to unlock driver’s door or all doors. Also will initiate and terminate *Panic. When pressed and release two times, will provide pulsed output or activate the Remote Start option when installed. When so equipped, this button can be used to operate an optional device connected to channel 4. When so equipped, this button can be used to operate an optional device connected to channel 5. Rev A: Add new URL 11/4/2011 128-8698a

****** Page 2 ****** PROGRAMMING TRANSMITTERS: NOTE: It is important to remember that during the programming mode, each individual step must be completed within 15 seconds of the previous step. If the 15 second time limit expires between steps, the unit will automatically exit the program mode. This is indicated by a long chirp from the siren. Non alarm models will flash the parking lights only to confirm the transmitter code has been learned and stored. NOTE: Because the system may be capable of sounding a siren, the vehicle horn, or both, where the siren chirp is referenced be- low, the siren may chirp, the horn may beep, or both devices may sound. NOTE: Some systems are capable of single button programming, if your alarm module is capable of this feature, simply complete step 4 of these programming instructions for each transmitter you wish to control your system and exit the program mode by switching off the ignition key TO PROGRAM ADDITIONAL TRANSMITTERS: 1) Enter the vehicle, and turn the ignition switch to the on position. 2) Press and release the valet push-button switch three times. NOTE: Some systems may use a combination push-button LED switch. In these systems the pushbutton and the dash- mounted LED are one and the same. 3) The dash mounted LED will flash lx, and the siren will chirp 1 x, indicating that the system is ready to accept programming of channel #1 which is arm/lock, disarm/unlock/unlock 2, and panic functions. 4) Press and hold the lock or lock/unlock symbol button of the transmit- ter you wish to program for 4 seconds or until a long chirp is heard from the siren. “Repeat step 4 for each transmitter you wish to program”. NOTE: If your transmitter button has the Lock/Unlock icon on one button, press and release the valet push button switch 2 times then move on to step #8. 5) Press and release the valet push button switch one time to advance to channel 2. The siren will chirp 2 times and the dash mounted LED will Flash 2 times, indicating that the unit is ready to accept programming for channel # 2 which is only used for separate lock and unlock button transmitters, and is the disarm/unlock/unlock 2 and panic. 6) Press and hold the unlock symbol button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren. “Repeat step 6 for each transmitter you wish to program”. 7) Press and release the valet push button switch one time to ad- vance to channel 3. The siren will chirp 3 times and the dash 2 128-8698a

****** Page 3 ****** mounted LED will Flash 3 times, indicating that the unit is ready to accept programming for channel # 3 which is the trunk re- lease/alternate output channel of the system. 8) Press and hold the trunk/key symbol button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren. ‘Repeat step 8 for each transmitter you wish to program”. 9) Press and release the valet push button switch one time to advance to channel 4 if so equipped. The siren will chirp 4 times and the dash-mounted LED will Flash 4 times, indicating that the unit is ready to accept programming for channel # 4, optional device (where equipped) 10) Press and hold the Option button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren ‘Repeat step 10 for each transmitter you wish to program”. 11) Press and release the valet push button switch one time to advance to channel 5 if so equipped. The siren will chirp 5 times and the dash- mounted LED will Flash 5 times, indicating that the unit is ready to accept programming for channel #5 optional device (where equipped) 1 2) Press and hold the second Option button of the transmitter you wish to program for 4 seconds or until a long chirp is heard from the siren. “Repeat step 12 for each transmitter you wish to program”. 13) Within 10 seconds, press and release the valet program switch one time. (Siren emits 6 short chirps indicating channel 6 has been entered) 14) Within 10 Seconds, Press and hold the unlock button, (or any unused button(s)), of the first transmitter you wish to control Channel 6 output, (Driver Priority 1) until a long chirp is heard from the siren. (Repeat this for each transmitter you wish to operate the Channel 6 output, Driver Priority 1) 15) Within 10 seconds, press and release the valet program switch one time. (Siren emits 7 short chirps indicating channel 7 has been entered) 16) Within 10 Seconds, Press and hold the unlock button (or any unused button(s)) of the first transmitter you wish to control Channel 7 output, (Driver Priority 2) until a long chirp is heard from the siren. (Repeat this for each transmitter you wish to operate the Channel 7 output, Driver Priority 2) NOTE: Channels 6 and 7 can be used as a separate output to control a function other than driver priority. Simply program- 3 128-8698a 3 of 8

****** Page 4 ****** ming any unused transmitter button other than the unlock button will allow complete Independent control of these outputs. ERASING TRANSMITTERS IF THEY HAVE BEEN LOST OR STOLEN: NOTE: Before you begin to erase the lost or stolen transmitter(s), have all transmitters available that you wish to remain programmed These will be used during the program process to identify transmitters that will continue to be used. Enter the transmitter program mode: 1. Turn the ignition switch to the “ON” position. 2. Within 10 seconds, press and release the valet/program switch three times. (Siren emits 1 short chirp indicating channel 1 has been entered) 3. Within 10 Seconds, press and hold the ARM or ARM/DISARM button of the first transmitter you wish to remain stored into the control unit until a single chirp is heard from the siren. (Repeat this for each transmitter you wish to remain stored in the control unit). The receiver stores up to four transmitters. To be certain all transmitter slots in the receiver are occupied with transmitters you wish to con- tinue to use, and all others are erased, you will have to fill all four receiver slots. If in step 3 you identified one transmitter, you will have to fill the additional 3 slots. If in step 3 you identified two transmitters, you will have to fill the additional two slots, etc.. 4. Press and hold any unused button or combination of buttons until a long chirp is heard from the siren. Release and press the button or button combination again and again until all remaining slots are full NOTE: The button or combination of buttons entered will also control the arm or arm/disarm function until additional transmitters are added. All unwanted transmitters are now deleted. REPRIORITIZING A TRANSMITTER’S PROGRAMMING: To reprogram a receiver channel with a different transmitter button once a code has been stored, there will be two options: 1 2. Enter the transmitter program mode of the receiver channel to be reprogrammed. Using any unused button or combination of but- tons, push out the stored code by pressing the unused button until a long chirp is heard, then repeat 3 additional times. After this, you can add any desired unused transmitter button. This action erases only the button stored of the transmitter you are programming. All other codes will remain stored. Enter the transmitter program mode. Using any transmitter button press and hold until a long chirp is heard. If a single chirp or multiple chirps, up to 7 chirps), are heard, the unit is Indicating that the transmi ter has already been programmed elsewhere In the re- ceiver. Release the transmitter button and within 5 seconds press and hold until a Iona chirp is heard. This action forces the unit to erase all stored codes of that transmitter. 4 128-8698a 4 of 8

****** Page 5 ****** The unit then exits the program mode the siren emits the program mode exit chirp pattern. All transmitter buttons for that transmltter must now be reprogrammed. Any other transmitter stored in the unit’s memory still remain operational. If the button is released and not pressed again within the 5 second period, no change in programming has been made to the receiver channel. The programmer can move onto a different channel or erase the transmitter codes as described in 1 above. BATTERY REPLACEMENT: The transmitter incorporates a small LED visible through the case which is used to indicate battery condition. You will notice a decrease in transmitter range as the battery condition deteriorates. Transmit- ter battery replacement is recommended at least every 10 to 12 months, depending upon how frequently the transmitter is used. To replace the battery: 1) Remove the 2 small # 0 Phillips head screw from the rear of the case. 2) Remove the rear cover to access the discharged battery paying attention to the proper polarity orientation. 3 Carefully remove and properly dispose of thedischarged battery. 4 Insert the new battery, being certain the metal key ring bar is in it’s proper location, close the case, then reinstall the 2 small case screw removed in step 1. 5) If you accidently dislodge the circuit board from the transmitter hous- ing, be certain that the rubber membrane is seated properly, and the buttons are properly exposed from the front view of the case, then insert the circuit board and return to step #4. This Transmitter uses CR203å Coin Cell Type Batteries. SEE ASSOCIATED DIAGRAMS ON FOLLOWING PAGE 5 128-8698a 5 of 8

****** Page 6 ****** PA-TANE COX •a. tLVAtiC 00000 CR2032 After removing the two #0 point phillips screws shown pry apart case with the edge of a finger nail or a small common screwdriver. Keep hold of the metal key ring loop to prevent it’s loss as it will separate from the transmitter case. Carefully remove the discharged battery by sliding it out from under the clip in the direction Indicated by the arrow in the diagram below. Properly dispose of the exhausted battery and insert a new CR2032 taking care to arrange it so that the + is facing up toward the + symbol on the battery clip. Reas- semble in the reverse of above. To purchase replacement transmitters or to get additional product information go to: pursuitcarsecurity.com 6 128-8698a

****** Page 7 ****** This device complies with FCC Rules Part 15 Operation is subiect to the following two conditions 1 this device may not cause harmful interference and 8 2 This device must accept any interference that may be received, including interference that may cause undesired operation. NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment 7 128-8698a 7 of 8

****** Page 8 ****** 0 2011 Audiovox Electronics Cap. 150 Marcus BVd. 8 Hauppauge, NY J 11788 128-8698a 128-8698a


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

AUDIOVOX ELECTRONICS PURSUIT 093BPR (01) PDF MANUAL

Leave a comment, question, review or page error below.

This site uses Akismet to reduce spam. Learn how your comment data is processed.