AUDIOVOX CODE ALARM PROFESSIONAL CA 3051 (01) PDF Document

To arm your AUDIOVOX CODE ALARM PROFESSIONAL CA 3051, follow these steps:

1. Turn the engine OFF, exit the vehicle, and close all doors, hood, and trunk.

2. Press and release the LOCK button of your Factory (OEM) transmitter one time.

The parking lights will flash once, the siren will chirp once, and the dash-mounted LED will begin to flash slowly, confirming the system is armed. If the siren sounds 3 chirps, you have left a door, trunk, or hood lid ajar. Simply close the opened entry point to provide full protection.

If the passive arming feature has been selected for your AUDIOVOX CODE ALARM PROFESSIONAL CA 3051:

1. Turn the engine OFF, exit the vehicle, and close all doors, hood, and trunk.

2. The dash-mounted LED will begin to flash rapidly, indicating that the 30-second passive arming timer has begun. If the LED does not flash, an entry point is ajar. Closing it will start the arming cycle.

3. If any entry point is opened during the 30-second cycle, arming will be suspended until all entry points are closed, at which point the cycle will begin again.

4. At the end of the 30 seconds, the parking lights will flash once, the siren will chirp once, and the dash-mounted LED will begin to flash slowly, confirming the system is armed.

When your AUDIOVOX CODE ALARM PROFESSIONAL CA 3051 is armed, the following protections are active:

Opening any protected entry point (hood, trunk, or doors) will trigger the alarm immediately. The siren will sound and the parking lights will flash for 30 seconds. The system will then stop and continue to monitor all entry points.

If a thief leaves a door open, the system will sound for six 30-second cycles, then shut down, isolate that specific triggered zone, and continue to protect all other zones.

The dash-mounted LED will flash slowly as a visual deterrent. This LED is a very low current light emitting diode and will not drain the battery, even if left for long periods.

Whenever the system is triggered, the vehicle’s parking lights will flash for the full siren sounding period.

Optional features when armed include: the interior courtesy light flashing during the siren sounding period, the vehicle’s starter circuit being disabled, and a shock sensor that triggers the alarm on strong impact or emits warning tones on lesser impact.

To disarm your AUDIOVOX CODE ALARM PROFESSIONAL CA 3051, press and release the UNLOCK button on your Factory (OEM) transmitter as you approach the vehicle. The parking lights will flash 2 times, the siren will chirp 2 times, and the dash-mounted LED will turn off.

NOTE: If passive arming mode is selected, the dash-mounted LED will start flashing rapidly after disarming, indicating the system is rearming. Opening any door will suspend this automatic arming.

If an intrusion attempt has occurred while you were away from the vehicle, the AUDIOVOX CODE ALARM PROFESSIONAL CA 3051 will inform you upon disarm. The siren will chirp 4 times and the parking lights will flash 3 times. Before turning on the ignition key, you should examine the dash-mounted LED’s flash pattern to identify the triggered zone.

After receiving an intrusion warning (4 chirps and 3 light flashes) upon disarming your AUDIOVOX CODE ALARM PROFESSIONAL CA 3051, observe the LED flash pattern before turning the ignition on:

• If the LED flashes 2 times…pause, 2 times…pause etc., an intrusion attempt was made to the hood, trunk, or by an accessory triggering device.

• If the LED flashes 3 times…pause, 3 times…pause etc., an intrusion attempt was made to the vehicle doors.

• If the LED flashes 4 times…pause, 4 times…pause etc., an intrusion attempt was made by impact or strong vibration detected by the shock sensor.

These LED intrusion warning indications are stored in the system’s memory and will be erased when the ignition switch is turned on.

The valet switch on your AUDIOVOX CODE ALARM PROFESSIONAL CA 3051 allows you to temporarily bypass all alarm functions. Remote panic and door lock features remain operational.

To enter valet mode:

1. Enter the vehicle and turn the ignition key to the ON position.

2. Press and hold the valet pushbutton switch until the dash-mounted LED turns on solid. The system will remain in valet mode.

To return to normal operation:

1. Press and release the push button switch any time the ignition is on.

Always remember to return the vehicle to the valet OFF position to ensure the vehicle remains protected.

If your Factory (OEM) transmitter is lost, has a failed battery, or is inoperative, you can disarm your AUDIOVOX CODE ALARM PROFESSIONAL CA 3051 using the valet/override switch. To bypass the system:

1. Open the vehicle door. The system will sound.

2. Turn the ignition key to the ON position.

3. Within 10 seconds, press and release the valet pushbutton switch.

The system will stop sounding and enter the by-passed mode. You can now start and operate the vehicle normally.

You can selectively eliminate or return the normal arm and disarm chirps on your AUDIOVOX CODE ALARM PROFESSIONAL CA 3051 by following these steps:

1. Turn the ignition key ON then OFF.

2. Within 10 seconds of turning the ignition key OFF, press and release the valet/override switch 3 times.

3. If the chirps were ON, you will hear 2 short chirps, indicating they are now turned OFF.

4. If the chirps were OFF, you will hear 1 short chirp, indicating they are now turned ON.

Whenever the system’s power has been disconnected, the chirps will be ON when power is reconnected.