ASTROAI A30 (01) PDF Document

Before using your ASTROAI A30, please be aware of the following warnings:

• Fully charge the product before use.

• This product contains small accessories which are a choking hazard for young children. Keep out of reach of children.

• Extended use is not recommended. Please cool down the product for at least 10 minutes after 10 minutes of continuous use.

• Please check the preset value and unit before use. Do not overinflate the tire, high pressure may cause injuries.

• Do not use the product as a car battery and do not use it to start the car while the jump starter is charging.

• Do not connect the red clamp to the black clamp.

• The product is intended only to start 12V vehicles and is prohibited for use on non-12V equipment such as aircraft and 24V vehicles/boats.

• Only use this product with the included battery clamps. Do not use the jumper clamps or cables if they appear damaged.

• Take off any metal accessories, such as rings, bracelets, or necklaces before operating the jump starter.

• Before starting your car, clean the battery terminals and inspect the jumper clamps for any damage. Dirty terminals and damaged clamps can affect performance.

• Repeatedly jumpstarting your vehicle in a short time frame will increase the likelihood of damage. To prevent this, ensure the jump starter has adequate breaks in between each use. If you are using the jump starter several times in a row, allow a 60-second break in between each use.

• Promptly remove the jump starter from the vehicle’s battery after successfully jumpstarting your car. Failure to do so may cause damage.

• Do not place the product in a high temperature, humid environment, or near flammable materials or strong magnetic fields.

• Be aware of the product’s charging, working, and storage temperature range. Do not expose it to direct sunlight or leave it in a high-temperature environment for a long time.

• Non-professionals should not disassemble, remodel, or repair the product.

• Handle the product with care to avoid dropping and other severe impacts.

• If any abnormalities occur (e.g. overheating, smoking, or burning) while using the jump starter, please turn it off, remove the clamps, and immediately contact customer support.

• Do not press the Boost Button before connecting to the car battery.

Please charge the ASTROAI A30 jump starter to 100% before using it. Connect its charging cable to the USB-C port. (A charging block is not included). The charging temperature should be between 32°F – 113°F (0°C – 45°C).

The battery level indicators are as follows:

• One bar: Under 25%

• Two bars: Between 25% and 50%

• Three bars: Between 50% and 75%

• Four bars: Between 75% and 100%

Note: The battery icon flashes while the jump starter is charging; once it’s fully charged, the battery icon will illuminate. The screen automatically turns off once the jump starter has finished charging.

Press the Power Button to turn the ASTROAI A30 on. To power it off, press and hold the Power Button for 2 seconds. The device also turns off automatically when there is no external load or output for over 30 seconds.

Note: For best jumping performance, ensure the jump starter’s battery level exceeds 75% and turn off any electrical devices inside your vehicle before starting your car.

1. Fully insert the smart battery clamps into the jump starter’s 12V port.

2. Connect the red clamp to the battery’s positive terminal (+) and the black clamp to the battery’s negative terminal (-). Proceed to the next step when the clamps’ indicator remains green. For other indicator statuses, see the indicator light description table.

3. Start your engine.

4. Remove the clamps from the battery.

1. Connection: Choose an appropriate nozzle based on the inflatable and tightly connect to it.

2. Setting: Press the Power Button to turn on the unit. Then, choose the appropriate inflation mode and adjust the preset pressure value according to the required air pressure of the inflatable.

• Press the Mode Button to switch between car, motorcycle, bicycle and ball inflation modes.

• Press and hold the Mode Button to switch units between Bar, PSI and Kpa.

• Press the “+” and “-” Buttons to adjust the preset value by 1PSI (0.1Bar/1kPa) increments.

• Press and hold the “+” and “-” Buttons to rapidly adjust the preset value.

3. Inflation: Press and hold the Start/Pause Button to start inflating. The machine will automatically stop when the inflation is complete.

Tip: To avoid overinflation, please confirm the maximum inflation pressure of the objects being inflated. Overinflating may cause explosions and personal injuries.

When the ASTROAI A30 jump starter is on, connect the USB cable to the USB output port to charge cell phones, tablets, and other devices.

When the machine is on, press the Light Button for 3 seconds to turn on the LED flashlight. Press it again to switch between flashing, SOS, and off modes.

• To maximize the battery’s performance and service life, please charge the jump starter when its battery level is lower than 75%.

• Please fully charge the jump starter if it will not be in use for an extended amount of time. Charge it every three months to extend its service life.

Slow inflation on your ASTROAI A30 could be caused by the following:

• Insufficient battery level.

• Check if the air hose leaks.

• Check if there is a good seal on the air hose’s ends.

• Check if the inflating object is leaking.

If your ASTROAI A30 fails to charge, try the following steps:

• Check if the charging cable is connected correctly.

• Ensure the outlet is powered.

• If the jump starter overheats, it will turn on its overheating protection feature and shut down for a few minutes. Once the unit cools down, try again.

• If the issue persists, contact customer support.

If your ASTROAI A30 fails to jumpstart your car, please check the following:

• Insufficient power level; you may need to charge the jump starter. Please charge your device to 75% or higher to successfully jumpstart your car.

• Inspect the battery terminals for any rust or dirt, as it could affect the connection quality. Clean up any residue and try again.

• If the jump starter overheats, it will turn on its overheating protection feature and shut down for a few minutes. Once the unit cools down, try again.

• Check if the battery clamps are connected to the wrong terminals (reversed).

• Poor connection between the clamps and battery; ensure a tight connection.

• The vehicle cannot start because of issues unrelated to battery power levels. Please use the appropriate equipment to check the battery or error code of the vehicle. This will help identify and address potential issues beyond the jump starter itself.

• If problems continue, contact customer support.

If the ASTROAI A30 shows a pressure value of zero during inflation, the object’s pressure value is too low for the device to detect.

If your ASTROAI A30 fails to power on, it could be due to:

• Insufficient power level or the jump starter is still charging.

• If it still won’t power on, contact customer support.

H0

• Error: Battery cell temperature too low; charger inserted but the device is not charging.

• Solution: Resume charging once the cell temperature returns to normal.

H1

• Error: Overheated battery cell during charging or use has triggered protection.

• Solution: When the cell temperature returns to normal, it will resume normal functionality.

H2

• Error: The air compressor temperature is too high; immediately stop using it.

• Solution: When the temperature returns to normal, it will resume its normal functionality.

H3

• Error: Overused air compressor has triggered protection.

• Solution: Wait for 5 minutes then restart the air compressor.

188

• Error: Device has stopped charging because the input voltage is higher than 11V.

• Solution: It will charge normally once connected to a power source that is lower than 10V.

You may dispose of the ASTROAI A30 jump starter when its service life has ended. Please recycle the recyclable parts according to local guidelines.