AKASO BRAVE 6 PLUS (01) PDF Document

No, the camera does not record sound when it is in the waterproof case.

Please use brand name microSD cards that meet these requirements:

1. microSD, microSDHC or microSDXC

2. UHS-III rating only

3. Capacity up to 64GB (FAT32)

Note: Please format the microSD card first in this camera before using. To keep your microSD card in good condition, reformat it on a regular basis. Reformatting erases all your content, so please make sure to offload your photos and videos before reformatting. FAT32 format microSD card stops recording when the file size reaches to 4GB, and starts to record again on a new file.

To Power On: Press and hold the Power button for 3 seconds. The camera beeps while the camera status light is on. When information appears on the display, your camera is on.

To Power Off: Press and hold the Power button for 3 seconds. The camera beeps while the camera status light is off.

Turn on the camera, swipe your finger across or up the screen to change modes.

Turn on the camera, press the Up button to turn on Wifi, and press the Up button again to turn off Wifi.

Video Mode is the default mode when you turn on the camera. In Video Mode, press the Shutter button, the camera starts recording video. Press the Shutter button again to stop recording video. Long press the Up or Down button to adjust the zoom level.

Swipe your finger across the screen to switch to Photo Mode after you turn on the camera. In Photo Mode, press the Shutter button to take photos. Long press the Up or Down button to adjust the zoom level.

Turn on the camera, swipe your fingers up the screen, and choose Video Settings to enter the Video Settings menu. You can change video settings in this mode.

If you turn on Driving Mode and connect the camera with a car cigarette lighter, the camera will turn on automatically if you start your car and will turn off if you stop your car.

In Time Lapse Video mode, press the Shutter button, and the camera records video from frames captured at specific intervals. Note: Time Lapse Video is captured without audio.

In Still Photo mode, the camera will automatically take still photos during video recording. The default setting is Off. Available intervals are 3 Sec/5 Sec/10 Sec/30 Sec.

Loop recording allows your camera to overwrite old files with new files. Once the memory card becomes full, the camera will delete the first video file to make room for the latest file. For example, if the setting for loop recording is “1 Minute”, then the camera will create video clips of 1 minute in length, and a 1-minute clip will be deleted when the camera needs more memory.

This setting adjusts the footage to offset for motion during capturing. The result is smoother footage, especially in activities with relatively small but fast motion like cycling, motorcycling, and handheld uses. The default setting is Off.

The angle refers to how much of the scene (measured in degrees) can be captured through the camera lens. Wide angle captures the largest amount of the scene, while Narrow angle captures the least. The options are Wide/Medium/Narrow, and the default setting is Wide.

Exposure lets you select an area that you want the camera to prioritize when determining exposure. This setting is particularly useful in shots where an important region might otherwise be over- or underexposed. The default setting is 0.

Self-Timer Mode gives a delay between pressing the shutter release and the shutter’s firing. The available intervals are 3 Sec/5 Sec/10 Sec/30 Sec, and the default setting is 3 Sec.

In burst mode, several photographs are captured in quick succession, so it is perfect for capturing fast-moving activities. The available settings are 3 Photos/5 Photos/10 Photos/15 Photos.

ISO determines the camera’s sensitivity to light and creates a trade-off between brightness and resulting image noise. Image noise refers to the degree of graininess in the image. In low light, higher ISO values result in brighter images, but with greater image noise. Lower values result in lower image noise, but darker images.

When you turn on Voice Control, the Voice Control icon will appear on the top of the screen. Below is a list of commands:

Pro Tips:

1. If you are recording video, you must stop recording before issuing a new command.

2. If you say “AKASO Take Photo” when you are recording video, the camera takes a still photo.

3. When controlling the action camera using voice commands, please speak at a normal speed. No need to deliberately slow down. Please put stress at the end of the sentence.

When you turn on Diving Mode, it can compensate for the lack of red light in underwater scenes. Diving Mode is designed to be used in tropical and blue water, optimized for use between 10 and 80 feet.

Go to Factory Reset in the settings and select Yes. This option resets all settings to their default values.

Turn on the camera, tap the Play button on the left side of the screen to enter the Playback Mode. In Playback Mode, swipe your finger across the screen to scroll through video or photo files.

1. Enter Playback mode. If your microSD card contains a lot of content, it might take a minute for it to load.

2. Swipe your finger across the screen or press Up/Down button to scroll through video or photo files.

3. Tap the Delete icon on the screen.

4. Are you sure delete files? Select Confirm to delete the file.

5. To exit Playback mode, tap Return button.

Please download and install the AKASO GO App in App Store or Google Play first.

1. Turn on the camera, press Up button to turn on the Wifi.

2. Connect the Wifi “Brave 6 Plus” and enter the password 1234567890 on your smartphone.

3. Open the AKASO GO App, choose Connect the camera → Wifi Connect.

To offload files to a computer using a card reader (sold separately) and your computer’s file explorer, connect the card reader to the computer, then insert the microSD card. You can then transfer files to your computer or delete selected files.

1. Open the AKASO GO App. Connect the camera with the App.

2. Click Playback to see all the videos and photos.

3. Tap the photo or video you want to download.

4. Click the Share at the right upper corner, and choose Download.

Note:

1. If you cannot offload videos or photos to iPhone or iPad, please enter Setting → Privacy → Photos, find “AKASO GO” and select “Read and Write”.

2. iPhone and iPad do not allow you to download 4K or 2.7K video via App, please offload 4K or 2.7K videos via card reader.

Please follow these guidelines to get the best performance from your camera:

1. For best audio performance, shake the camera or blow on the mic to remove debris from the microphone holes.

2. To clean the lens, wipe it with a soft, lint-free cloth. Do not insert foreign objects around the lens.

3. Don’t touch the lens with fingers.

4. Keep the camera away from drops and bumps, which may cause damage to the parts inside.

5. Keep the camera away from high temperature and strong sunshine to avoid being damaged.

To maximize battery life, follow these guidelines when possible:

• Turn off Wireless Connections

• Capture video at lower frame rates and resolutions

• Use Screen Saver setting.

VIDEO

To record Video, verify the camera in Video mode.

To start recording: Press the Grey Video Button. The camera will emit one beep and the camera light will flash while recording.

To stop recording: Press the Grey Video Button again. The camera will emit one beep and the camera light will stop flashing while recording.

PHOTO

To capture a photo, verify the camera in Photo mode.

To take a photo: Press the Red Photo Button. The camera will emit a camera shutter sound.

1. Use a 1.8mm Phillips tip screwdriver to remove the 4 screws on the back cover of the remote, allowing you to open it.

2. Remove another 4 screws on PCB board.

3. Lift the PCB board and slide out the battery. Note: Do NOT rotate the PCB board to avoid reversing the camera and video button functions.

4. Install the new battery, keeping the “+” pole facing up.

5. Install all 4 screws back onto the PCB board.

6. Install all 4 screws back into the cover.