ADC AD-320 (01) PDF Document

Please observe all safety precautions displayed on the equipment and in the manual.

FOR YOUR SAFETY:

• DO NOT store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

• DO NOT dry mop heads in the dryer.

• DO NOT use the dryer in the presence of dry cleaning fumes.

WARNING:

• Children should NOT be allowed to play on or in the dryer(s).

• Children should be supervised if near dryer(s) in operation.

CAUTION:

• Dryer(s) should NEVER be left unattended while in operation.

IMPORTANT:

• Dryer(s) must not be installed or stored in an area where it will be exposed to water and/or weather.

• The wiring diagram for the dryer is located in the front electrical control box area.

Instructions to be followed in the event the user smells gas must be posted in a prominent location. These instructions shall be obtained from the local gas supplier.

1. When turning on power or when no cycle is in progress, the L.E.D. displays will read “FILL” and/or “Amount toStart.”

2. Insert coin(s). Once the correct “Amount to Start” has been inserted, the display will read “PUSH – tEnP”.

3. Select the temperature by pushing “HI-TEMP,” “LO-TEMP,” or “PERM-PRESS.” The basket (tumbler) will start to rotate, and the L.E.D. display will read the temperature cycle selected and the drying time.

4. The basket (tumbler) will continue to rotate through the drying and cooling cycles, showing time counting downward.

NOTE: If the door is opened during a cycle, both the heat and motor will stop. However, the DMC computer will continue to count down in time. Continuation of the cycle will resume only after the door has been closed and any one of the three (3) temperature selection buttons is again depressed.

5. Upon completion of drying and cooling cycles, the buzzer (tone) will sound, and the L.E.D. display will read “donE” for five (5) seconds, at which time the basket (tumbler) will shut off.

1. When turning on power or when no cycle is in progress, the L.E.D. displays will read “FILL” and/or “Amount to Start.”

2. Insert coin(s). Once the correct “Amount to Start” has been inserted, the L.E.D. display will read “PUSH – tEnP”.

3. Select the temperature by pushing “HI-TEMP,” “LO-TEMP,” or “PERM-PRESS.” The basket (tumbler) will start, the L.E.D. display will read the temperature cycle selected, and the drying time portion of the L.E.D. display will read “00” and count upward as the time elapses.

NOTE: If the door is opened during a cycle, both the heat and motor will stop. However, the DMC computer will continue to count upwards in time. Continuation of the cycle will resume only after the door has been closed and any one of the three (3) temperature selection buttons is again depressed.

4. Once the preprogrammed dryness level and cool down period have been reached or maximum automatic time has expired, whichever comes first, the buzzer (tone) will sound, and the L.E.D. display will read “donE” for five (5) seconds, at which time the basket (tumbler) will shut off.

1. When turning on power or when no cycle is in progress, the L.E.D. displays will read “FILL” and/or “FrEE”.

2. Select temperature. The basket (tumbler) will start rotating, the L.E.D. display will read the temperature cycle selected, and the drying time portion of the L.E.D. display will read the value of “Adrt” (maximum time for automatic dry), counting downward as time elapses when in the timed mode and upward when in the automatic mode.

NOTE: If the door is opened during a cycle, both the heat and motor will stop. However, the Dual Microprocessor Controller (DMC) computer will continue to count upwards in time. Continuation of the cycle will resume only after the door has been closed, and one of the three (3) temperature selection buttons is again depressed.

3. Once the preprogrammed dryness level and cool down period has been reached or maximum automatic time has expired, whichever comes first, the buzzer (tone) will sound, and the L.E.D. display will read “donE” for five (5) seconds, at which time the basket (tumbler) will shut off.

To change programs or to put the Dual Microprocessor Controller (DMC) computer in the temperature or coin count display modes, the Program Switch (PS) located on the back side of the DMC computer must be put into the closed position (PSC).

Initial Conditions: The power is on, the dryer is idling, and no drying cycle is in progress.

Observations: Once in program mode, program locations can be indexed upward with the aid of the “HI-TEMP” key and downward with the aid of the “LO-TEMP” key.

NOTE: Holding the “HI-TEMP” or “LO-TEMP” keys down continuously will automatically strobe/scroll through ALL the program locations available.

The temperature display mode displays the temperature inside each basket. This feature is helpful for servicing the dryers.

Initial Conditions: The power is on, the dryer is idling, and no drying cycles are in progress.

If the baskets were both running, the following sequence would take place:

Observations: Both baskets (tumblers) will continue their respective cycles until the end without any change.

The Right Coin Count feature displays the total number of coins sensed by the right coin switch.

Initial Conditions: The power is on, the dryer is idling, and no drying cycles are in progress.

To view the Right Coin Count:

To clear the Right Coin Count:

Note: Open Program Switch (PS) to exit from the display mode.

The Left Coin Count feature displays the total number of coins sensed by the left coin switch.

Initial Conditions: The power is on, the dryer is idling, and no drying cycles are in progress.

To view the Left Coin Count:

To clear the Left Coin Count:

Note: Open Program Switch (PS) to exit from the display mode.

You can change the temperature scale in Program Location 01 (PL01).

NOTE: As a result of changing the temperature scale, all applicable temperature registers (i.e., PL03, PL04, PL05, PL06, PL07, and PL08) will automatically be converted to their equivalent Celsius temperatures.

Follow these steps to access and change the HI-drY-tEnp register (PL03).

Accessing PL03:

Changing the temperature set-point:

NOTE: In programming mode, the PERM-PRESS key functions as the “ENTER” key. The high temperature is programmable from 100°F to 150°F in five-degree increments or from 38°C to 65°C in one-degree increments.

¹ For compatibility with existing controls.

² For Automatic Cycle ONLY.

The optional 9 Volt Battery Back-Up allows the dryer to maintain its operating status during a momentary power interruption. The battery is not included with the option.

It is suggested that the battery be replaced at least once a year or as found necessary. The battery life will depend on the age of the battery, the amount of power interruptions, and the back-up time used.

IMPORTANT: For proper operation use alkaline batteries ONLY. Suggest Eveready Energizer, Duracell, or equivalent. DO NOT USE CARBON TYPE BATTERIES.