A-NEUVIDEO ANI-705WPT (01) PDF MANUAL


Post questions, comments, reviews or page errors in the comment box below.

Click here to download A-NEUVIDEO ANI-705WPT (01) PDF MANUAL


PDF Content Summary:

****** Page 1 ****** ANI-705WPT HDMI over Single CAT5e1617 Wall-plate Transmitter RS232 IN POWER LINK IR2 Extender Blaster LAN DC 24V HDMI IN A-NeuVideo.com Frisco, Texas 75036 A > NEIJ VIDEO AUDIO / VIDEO MANUFACTURER

****** Page 2 ****** 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. SAFETY INFORMATION To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. Follow all instructions printed on unit chassis for proper operation. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and excessive moisture. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by any warranty. Turn power off and disconnect unit from AC current before making connections. Never hold a power switch in the “ON” position. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to qualified service personnel. There are no user serviceable parts inside. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to other devices. Do not drive the inputs with a signal level greater than that required to drive equipment to full output. The equipment power cord should be unplugged from the outlet when left unused for a long period of time. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing. Service Information Equipment should be serviced by qualified service personnel when: A. The power supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the equipment. C. The equipment has been exposed to rain. D. The equipment does not appear to operate normally, or exhibits a marked change in performance. E. The equipment has been dropped, or the enclosure damaged. THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.

****** Page 3 ****** A»NEUVIDEO CONTENTS INTRODUCTION & CONTENTS FEATURES . SPECIFICATIONS HARDWARE DESCRIPTION IR PIN ASSIGNMENT CONNECTION DIAGRAM DEAN CUSTOMER 2 €3 4 5 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. INTRODUCTION The ANI-705WPT is a CAT5e/6/7 over HDMI Wall-Plate Transmitter that can receive uncompressed audio/video over a single run of CAT5e/6/7 cable up to —328 WI 00M. It has the added benefit of control through the built-in RS-232 pass-through and 2-way IR control and a LAN serving connection. This product has a 3 year warranty. PACKAGE CONTENTS Before attempting to use this unit, please check the packaging and make sure the following items are contained in the shipping carton: • ANI-705WPT HDMI over Single CAT5e/6/7 Transmitter • IR Blaster • IR Extender • 24V/1.25A DC Power Adaptor • Users Guide APPLICATIONS • Household entertainment sharing and control • Lecture room display and control • Showroom display and control • Meeting room presentation and control • Classroom display and control SYSTEM REQUIREMENTS HDMI source device such as a DVD/Blu-ray player and an HDMI equipped display (TV or monitor). TABLE OF CONTENTS SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product. • Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit. Do not attach the power supply cabling to building surfaces. Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged. Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit. DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for any infringements of patents or other rights of third parties which may result from its use. We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update or to keep current the information contained in this document. We reserve the right to make improvements to this document and/ or product at any time and without notice. COPYRIGHT NOTICE No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means electronic, mechanical, magnetic, optical, chemical, manual, or otherwise — without the express written permission and consent. O Copyright 2017. All Rights Reserved. Version 1.0 MAY 2017 TRADEMARK ACKNOWLEDGMENTS All products or service names mentioned in this document may be trademarks of the companies with which they are associated. 1

****** Page 4 ****** A»NEUVIDEO FEATURES FEATURES & SPECIFICATIONS • HDMI (with 3D format and 4K2K resolution support), HDCP and DVI compliant • Supports HDCP repeater and CEC bypass functions • Simultaneous transmission of uncompressed video/audio and data over a single CAT5e/6/7 cable up to 328ft/100M • HDBaseTT'” 5Play convergence: uncompressed high-definition Video and Audio, LAN serving and IR/RS-232 Control pass-through • Supports uncompressed video up to 4K2K resolution (3840×2160@30Hz or 4096×2160@24Hz) • Supports pass-through of high-definition audio formats LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio • US 2Gang wall-plate design and easy installation NOTE: 1. This system was tested with CAT6/23AWG and CAT5e/24AWG cables, results may vary with cables of a different specification. 2. For playback of 4K2K HDMI source signals, a 4K2K capable display and High Speed HDMI cables are required. SPECIFICATIONS • Video Bandwidth: 340MHz/10.2Gbps • Input Ports: (1) HDMI, (1) I-AN, (1) IR Extender, (1) RS-232 • Output Ports: (1) CAT5e/6/7, (1) IR Blaster • CAT5e1617 Cable Distance: Up to 328 ft/100M • HDMI Resolution: Up to 4K2K (3840×2160@30Hz / 4096×2160@24Hz) • IR Frequency: 30-50KHz • ESD Protection: Human body model: • ±8kV (air-gap discharge) • ±4kV (contact discharge) • Dimensions (WxDxH): 4.7 x 4.3 x 1.6 in (119.5x110x40mm) *Including jacks • Weight: 13 oz/353g • Chassis Material: Metal • Silkscreen Color: White • Operating Temperature: 320F 1040F (OOC-400C) • Storage Temperature: -40F 1400F (-200C-600C) • Relative Humidity: RH (no condensation) • Power Supply: 24V/1.25A DC (US/EIJ standards, CE/FCC/UL certified) • Power Consumption (W): 15W As product improvements are continuous, specifications are subject to change without notice. CATSE/6/7 CABLE SPECIFICATION CABLE TYPE RANGE CAT5e/6/7 328 WI 230 ft/70M PIXEL CLOCK RATE 225MHz VIDEO DATA RATE s5.3Gbps (HD Video) > 5.3Gbps (Ultra HD Video) 2 SUPPORTED VIDEO Up to 1080p, 60Hz, 36bits, 3D (data rates lower than 5.3Gbps or below 225MHz TMDS clock) 4K2K, 30Hz video formats

****** Page 5 ****** A»NEUVIDEO FRONT & BACK PANELS HARDWARE DESCRIPTION ‘O RS-232 IN POWER O LINK O oo Extender Blaster 1 2 3 4 5 6 DC 24V HDMI IN 7 8 O RS-232 IN: Connects to a PC/laptop or RS-232 control system with D-sub 9-pin male cable for the transmission of RS-232 commands. @ POWER LED: This LED will illuminate when the transmitter is connected to a power supply. O IR 2 EXTENDER: Connects an IR Extender cable for IR signal reception. Signals received will be transmitted from any IR blaster connected to the receiver unit. Ensure that the remote being used is within the direct line-of-sight of the IR Extender. O IR 1 BLASTER: Connect an IR Blaster cable for IR signal transmission. IR signals received by an IR extender connected to the receiver unit will be transmitted by this blaster. Place the IR Blaster in direct line-of-sight of the equipment to be controlled. O LINK LED: This LED will illuminate when both the source connected to the transmitter and the display connected to the receiver are connected. O LAN: Connects to an active network for LAN serving and Telnet/Web GUI control. When the transmitter or any compatible LAN equipped receivers are connected to a network, this allows the network access (including internet access if available) to be shared between the transmitter and connected receiver. Connect any Ethernet equipped device e.g. a Smart TV or games console to the LAN port of a receiver for that device to share the network/internet access. O HDMI IN: Connects to an HDMI source device such as a DVD or Bluray player. O DC 24V: Connects the 24 V DC power supply to the transmitter and plug the adaptor into an AC outlet. O CAT5e/6/7 OUT: Connects to the receiver unit with a single CAT5e/6/7 cable for transmission of all data signals. 3

****** Page 6 ****** A»NEUVIDEO PIN ASSIGNMENT IR Blaster IR Extender D-SUB 9-PIN DEFINITIONS PIN 1 2 3 4 5 DEFINITIONS N/C TxD/RxD RxD/TxD N/C GND PIN 6 7 8 9 OPERATION CONTROLS & FUNCTIONS Power 3.3V IR Blaster Signal NC IR Signal Power 3.3V Grounding DEFINITIONS N/C N/C N/C N/C 4

****** Page 7 ****** A»NEUVIDEO CONNECTION DIAGRAM RS-232 Equipped PC or Control System RS-232 RS-232 RS-232 Equipped HDMI Switcher Extender CONNECTION DIAGRAM DVD or Blu-ray Player Internet Modem or Router LAN Serving Single CAT5e/6/7 Cable HDMI Input Blaster Power Supply r Extender Note: Only the transmitter unit needs to be powered and can power the receiver unit via POE. Notebook LAN Serving HDMI OUtPUt Blaster 1.5m TV or Monitor 5

****** Page 8 ****** A»NEUVIDEO TERMS & CONDITIONS OF USE PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc. at the return address set forth on the Product’s packing label at your expense. A-NeuVideo, Inc. may modify these Terms and Conditions at anytime, without notice to you. RESTRICTIONS ON USE OF THE PRODUCT It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product. You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be borne by you and you agree to indemnify and hold harmless A-NeuVideo, Inc. from and against any such damage. The Product is protected by certain intellectual property rights owned by or licensed to A-NeuVideo. Any intellectual property rights pertaining to the Product are licensed to you by A-NeuVldeo, Inc. and/or its affiliates, including any manufacturers or distributors of the Product (collectively, “A-NeuVideo”) for your personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product. The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by A-NeuVideo for your personal use only. A-NeuVideo does not transfer either the title or the intellectual property rights to the Product and A-NeuVideo retains full and complete title to the intellectual property rights therein. All trademarks and logos are owned by A-NeuVideo or its licensors and providers of the Product, and you may not copy or use them in any manner without the prior written consent of A-NeuVideo, which consent may be withheld at the sole discretion of A-NeuVldeo. The functionality and usability of the Product is controlled by A-NeuVideo, Inc. from its offices within the State of Texas, United States of America A-NeuVideo makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided with respect thereto. You are advised that the Product may be subject to U.S. export controls. Disclaimers and Limitation of Liability A-NeuVideo may change or modify the Product at any time, from time to time. THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. A-NEUVIDEO DOES NOT WARRANT OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE. A-NeuVideo has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product. TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, A-NEUVIDEO DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. A-NEUVIDEO DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT. A-NEUVIDEO DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS. A-NEUVIDEO WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT A-NEUVIDEO) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY A-NEUVIDEO. UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL A-NEUVIDEO BE LIABLE FORANY SPECIAL OR CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF A-NEUVIDEO OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL A-NEUVIDEO’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU PAID TO A-NEUVIDEO, IF ANY, FOR THE PRODUCT. END OF DOCUMENT 6


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE – USER MANUAL

OWNER GUIDE – OWNER MANUAL

REFERENCE GUIDE – REFERENCE MANUAL

INSTRUCTION GUIDE – INSTRUCTION MANUAL

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.