Post questions, comments, reviews or page errors in the comment box below.
PDF Content Summary:
****** Page 1 ****** ANI-705WPR CAT5e/6/7 over HDMI Wall-Plate Receiver with IRIRS-232/LAN/PoE RS-232 OUT POWER LINK IR2 Extender Blaster LAN HDMI OUT A-NeuVideo.com Frisco, Texas 75036 A > NEIJ VIDEO AUDIO / VIDEO MANUFACTURER
****** Page 2 ****** 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. 18. 19. SAFETY INFORMATION To ensure the best results from this product, please read this manual and all other documentation before operating your equipment. Retain all documentation for future reference. Follow all instructions printed on unit chassis for proper operation. To reduce the risk of fire, do not spill water or other liquids into or on the unit, or operate the unit while standing in liquid. Make sure power outlets conform to the power requirements listed on the back of the unit. Keep unit protected from rain, water and excessive moisture. Do not attempt to clean the unit with chemical solvents or aerosol cleaners, as this may damage the unit. Dust with a clean dry cloth. Do not use the unit if the electrical power cord is frayed or broken. The power supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords and plugs, convenience receptacles, and the point where they exit from the appliance. Do not force switched or external connections in any way. They should all connect easily, without needing to be forced. Always operate the unit with the AC ground wire connected to the electrical system ground. Precautions should be taken so that the means of grounding of a piece of equipment is not defeated. AC voltage must be correct and the same as that printed on the rear of the unit. Damage caused by connection to improper AC voltage is not covered by any warranty. Turn power off and disconnect unit from AC current before making connections. Never hold a power switch in the “ON” position. This unit should be installed in a cool dry place, away from sources of excessive heat, vibration, dust, moisture and cold. Do not use the unit near stoves, heat registers, radiators, or other heat producing devices. Do not block fan intake or exhaust ports. Do not operate equipment on a surface or in an environment which may impede the normal flow of air around the unit, such as a bed, rug, carpet, or completely enclosed rack. If the unit is used in an extremely dusty or smoky environment, the unit should be periodically “blown free” of foreign dust and matter. To reduce the risk of electric shock, do not remove the cover. There are no user serviceable parts inside. Refer all servicing to qualified service personnel. There are no user serviceable parts inside. When moving the unit, disconnect input ports first, then remove the power cable; finally, disconnect the interconnecting cables to other devices. Do not drive the inputs with a signal level greater than that required to drive equipment to full output. The equipment power cord should be unplugged from the outlet when left unused for a long period of time. Save the carton and packing material even if the equipment has arrived in good condition. Should you ever need to ship the unit, use only the original factory packing. Service Information Equipment should be serviced by qualified service personnel when: A. The power supply cord or the plug has been damaged. B. Objects have fallen, or liquid has been spilled into the equipment. C. The equipment has been exposed to rain. D. The equipment does not appear to operate normally, or exhibits a marked change in performance. E. The equipment has been dropped, or the enclosure damaged. THIS SAFETY INFORMATION IS OF A GENERAL NATURE AND MAY BE SUPERSEDED BY INSTRUCTIONS CONTAINED WITHIN THIS MANUAL.
****** Page 3 ****** A»NEUVIDEO CONTENTS INTRODUCTION & CONTENTS FEATURES . SPECIFICATIONS HARDWARE DESCRIPTION IR PIN ASSIGNMENT CONNECTION DIAGRAM DEAN CUSTOMER 2 €3 4 5 Thank you for purchasing this product. For optimum performance and safety, please read these instructions carefully before connecting, operating or adjusting this product. Please keep this manual for future reference. INTRODUCTION The ANI-705WPR is a CAT5e/6/7 over HDMI Wall-Plate Receiver that can receive uncompressed audio/video over a single run of CAT5e/6/7 cable up to -328 WI OOM with POE, IR, RS-232 and I-AN for data transmission rates of 100Mbps. A true HDBaseTTU 5Plar solution to make your home or office more efficient and easy with control. This product has a 3 year warranty. PACKAGE CONTENTS Before attempting to use this unit, please check the packaging and make sure the following items are contained in the shipping carton: • ANI-705WPR CAT5e/6/7 to HDMI with IR/RS-232/LAN/PoE Receiver • IR Extender (included with Receiver module only* ) • Users Guide *Both the IR Blaster and IR Extender are NOT included with EACH module. APPLICATIONS • Household entertainment sharing and control • Lecture room display and control • Showroom display and control • Meeting room presentation and control for projector • Classroom display and control SYSTEM REQUIREMENTS Input HDMI over a CAT5e/6/7 transmitter with source signal and HDMI equipped output display (TV/display). TABLE OF CONTENTS SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons. To prevent fire or shock hazard, do not expose the unit to rain, moisture or install this product near water. • Never spill liquid of any kind on or into this product. • Never push an object of any kind into this product through any openings or empty slots in the unit, as you may damage parts inside the unit. Do not attach the power supply cabling to building surfaces. Use only the supplied power supply unit (PSU). Do not use the PSU if it is damaged. Do not allow anything to rest on the power cabling or allow any weight to be placed upon it or any person walk on it. To protect the unit from overheating, do not block any vents or openings in the unit housing that provide ventilation and allow for sufficient space for air to circulate around the unit. DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. We assume no responsibility for any infringements of patents or other rights of third parties which may result from its use. We assume no responsibility for any inaccuracies that may be contained in this document. We make no commitment to update or to keep current the information contained in this document. We reserve the right to make improvements to this document and/ or product at any time and without notice. COPYRIGHT NOTICE No part of this document may be reproduced, transmitted, transcribed, stored in a retrieval system, or any of its part translated into any language or computer file, in any form or by any means electronic, mechanical, magnetic, optical, chemical, manual, or otherwise — without the express written permission and consent. O Copyright 2016. All Rights Reserved. Version 1.2 AUG 2016 TRADEMARK ACKNOWLEDGMENTS All products or service names mentioned in this document may be trademarks of the companies with which they are associated. 1
****** Page 4 ****** A»NEUVIDEO FEATURES • HDMI with 3D, 4K2K supported, HDCP and DVI compliant • Supports HDCP repeater and CEC bypass FEATURES & SPECIFICATIONS • Simultaneous transmission of uncompressed data over a single CAT5e/6/7 cable up to -328 ft/100M • HDBaseTm 5Pla)P Convergence: Uncompressed high definition video and audio, LAN, Power over Ethernet and RS-232/lR Controls • Uncompressed video support up to 3840×2160@30Hz or 4096×2160@24Hz • High definition audio supported up to LPCM 7.1CH, Dolby TrueHD, Dolby Digital Plus and DTS-HD Master Audio • IJS2 gang wall-plate design SPECIFICATIONS • Video Frequency: 300MHz/9Gbps • Input Ports: (1) IR Extender, (1) CAT5e/6/7 • Output Ports: (1) HDMI, (1) IR Blaster, (1) LAN, (1) RS-232 • CAT5e1617 Cable Distance: Up to 328 ft/100M • HDMI Resolution: Up to 4K2K (3840×2160@30Hz / 4096×2160@24Hz) • IR Frequency: 30-50KHz • ESD Protection: Human body model: • ±8kV (air-gap discharge) • ±4kV (contact discharge) • Dimensions (WxDxH): 4.7 x 4.3 x 1.6 in (119.5x110x40mm) *Including jacks • Weight: 13 oz/353g • Chassis Material: Metal • Silkscreen Color: White • Operating Temperature: 320F 1040F (OOC-400C) • Storage Temperature: -40F 1400F (-200C-600C) • Relative Humidity: RH (no condensation) • Power Consumption (W): 8W As product improvements are continuous, specifications are subject to change without notice. CATSE/S/7 CABLE SPECIFICATION CABLE TYPE RANGE PIXELCLOCK RATE VIDEO DATA RATE CAT5e/6/7 196 ft/60M 114ft/35M 225MHz s5.3Gbps (HD Video) > 5.3Gbps (Ultra HD Video) 2 SUPPORTED VIDEO Up to 1080p, 60Hz, 36bits, 3D (data rates lower than 5.3Gbps or below 225MHz TMDS clock) 4K2K, 30Hz video formats
****** Page 5 ****** A»NEUVIDEO FRONT PANEL RS232 OUT POWER LINK IRI EXTENDER BLASTER HARDWARE DESCRIPTION LAN HDMI OUT O LAN: Connects to an active network for LAN and Telnet/ Web GUI control. When the transmitter or any compatible LAN equipped receivers are connected to a network, this allows the network access (including internet access if available) to be shared between the transmitter and all connected receivers. Connect any Ethernet equipped device e.g. a Smart TV or game consoles to the LAN port of a receiver for that device to share the network/internet access. O RS-232 OUT: This slot is to connect the D-Sub 9-pin cable from device equipment to receive RS-232 commands. O POWER LED: This LED will illuminate when the device is connected to a power supply. O LINK LED: This LED will illuminate when both the CAT5e/6 input and output signals are connected. O IRI EXTENDER: This slot is to connect with the IR Receiver cable, included in the package, for IR signal receiving. O IR2 BLASTER: This slot is to connect with the IR Blaster cable, included in the package, for IR signal transmitting. O HDMI OUT: This slot is to connect with a HDMI TV/monitor for display HDMI input source signal. BACK PANEL O CAT5e/6/7 IN: Connects from the HDMI to the CAT5e/6/7 Transmitter for signal displaying. 3
****** Page 6 ****** A»NEUVIDEO IA PIN ASSIGNMENT IR Blaster IR Receiver D-SUB 9-PIN DEFINITIONS PIN 1 2 3 4 5 DEFINITIONS N/C TxD/RxD RxD/TxD N/C GND PIN 6 7 8 9 OPERATION CONTROLS & FUNCTIONS Power 5V IR Blaster Signal NC O IR Signal Power 5V Grounding DEFINITIONS N/C N/C N/C N/C 4
****** Page 7 ****** A»NEUVIDEO CONNECTION DIAGRAM CATS(IOOM Ree CONNECTION DIAGRAM HDMI Coble Projector Blu-ray’s 5
****** Page 8 ****** A»NEUVIDEO TERMS & CONDITIONS OF USE PLEASE READ THE FOLLOWING TERMS AND CONDITIONS CAREFULLY BEFORE USING THIS HARDWARE, COMPONENTS AND SOFTWARE PROVIDED BY, THROUGH OR UNDER A-NeuVideo, INC (COLLECTIVELY, THE “PRODUCT”). By using installing or using the Product, you unconditionally signify your agreement to these Terms and Conditions. If you do not agree to these Terms and Conditions, do not use the Product and return the Product to A-NeuVideo, Inc. at the return address set forth on the Product’s packing label at your expense. A-NeuVideo, Inc. may modify these Terms and Conditions at anytime, without notice to you. RESTRICTIONS ON USE OF THE PRODUCT It is your responsibility to read and understand the installation and operation instructions, both verbal and in writing, provided to you with respect to the Product. You are authorized to use the Product solely in connection with such instructions. Any use of the Product not in accordance with such instructions shall void any warranty pertaining to the Product. Any and all damages that may occur in the use of the Product that is not strictly in accordance with such instructions shall be borne by you and you agree to indemnify and hold harmless A-NeuVideo, Inc. from and against any such damage. The Product is protected by certain intellectual property rights owned by or licensed to A-NeuVideo. Any intellectual property rights pertaining to the Product are licensed to you by A-NeuVldeo, Inc. and/or its affiliates, including any manufacturers or distributors of the Product (collectively, “A-NeuVideo”) for your personal use only, provided that you do not change or delete any proprietary notices that may be provided with respect to the Product. The Product is sold to you and any use of any associated intellectual property is deemed to be licensed to you by A-NeuVideo for your personal use only. A-NeuVideo does not transfer either the title or the intellectual property rights to the Product and A-NeuVideo retains full and complete title to the intellectual property rights therein. All trademarks and logos are owned by A-NeuVideo or its licensors and providers of the Product, and you may not copy or use them in any manner without the prior written consent of A-NeuVideo, which consent may be withheld at the sole discretion of A-NeuVldeo. The functionality and usability of the Product is controlled by A-NeuVideo, Inc. from its offices within the State of Texas, United States of America A-NeuVideo makes no representation that materials pertaining to the Product are appropriate or available for use in other locations other than the shipping address you provided with respect thereto. You are advised that the Product may be subject to U.S. export controls. Disclaimers and Limitation of Liability A-NeuVideo may change or modify the Product at any time, from time to time. THE PRODUCT IS PROVIDED “AS IS” AND WITHOUT WARRANTIES OF ANY KIND EITHER EXPRESS OR IMPLIED. A-NEUVIDEO DOES NOT WARRANT OR MAKE ANY REPRESENTATIONS REGARDING THE USE OR THE RESULTS OF THE USE OF THE PRODUCT’S CORRECTNESS, ACCURACY, RELIABILITY, OR OTHERWISE. A-NeuVideo has no duty or policy to update any information or statements pertaining to the Product and, therefore, such information or statements should not be relied upon as being current as of the date you use the Product. Moreover, any portion of the materials pertaining to the Product may include technical inaccuracies or typographical errors. Changes may be made from time to time without notice with respect to the Product. TO THE FULLEST EXTENT PERMISSIBLE PURSUANT TO APPLICABLE LAW, A-NEUVIDEO DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NON-INFRINGEMENT. A-NEUVIDEO DOES NOT WARRANT THE ACCURACY, COMPLETENESS OR USEFULNESS OF ANY INFORMATION WITH RESPECT TO THE PRODUCT. A-NEUVIDEO DOES NOT WARRANT THAT THE FUNCTIONS PERTAINING TO THE PRODUCT WILL BE ERROR-FREE, THAT DEFECTS WITH RESPECT TO THE PRODUCT WILL BE CORRECTED, OR THAT THE MATERIALS PERTAINING THERETO ARE FREE OF DEFECTS OR OTHER HARMFUL COMPONENTS. A-NEUVIDEO WILL USE ITS REASONABLE EFFORTS TO CORRECT ANY DEFECTS IN THE PRODUCT UPON TIMELY WRITTEN NOTICE FROM YOU NOT TO EXCEED 10 BUSINESS DAYS AFTER RECEIPT BY YOU OF THE PRODUCT, BUT YOU (AND NOT A-NEUVIDEO) ASSUME THE ENTIRE COST OF ALL NECESSARY SERVICING, REPAIR AND CORRECTION THAT WAS CAUSED BY YOU UNLESS OTHERWISE AGREED TO IN A SEPARATE WRITING BY A-NEUVIDEO. UNDER NO CIRCUMSTANCES, INCLUDING, BUT NOT LIMITED TO, NEGLIGENCE, SHALL A-NEUVIDEO BE LIABLE FORANY SPECIAL OR CONSEQUENTIAL DAMAGES THAT RESULT FROM THE USE OF, OR THE INABILITY TO USE THE PRODUCT IN ACCORDANCE WITH ITS SPECIFICATIONS, EVEN IF A-NEUVIDEO OR ITS REPRESENTATIVES HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. IN NO EVENT SHALL A-NEUVIDEO’S TOTAL LIABILITY TO YOU FROM ALL DAMAGES, LOSSES, AND CAUSES OF ACTION (WHETHER IN CONTRACT, OR OTHERWISE) EXCEED THE AMOUNT YOU PAID TO A-NEUVIDEO, IF ANY, FOR THE PRODUCT. END OF DOCUMENT 6
FREE ENGLISH PDF
USER GUIDE – USER MANUAL
OWNER GUIDE – OWNER MANUAL
REFERENCE GUIDE – REFERENCE MANUAL
INSTRUCTION GUIDE – INSTRUCTION MANUAL