A-DEC 311FLT (02) PDF MANUAL

A-DEC 311FLT (02) PDF SUMMARY:

How do I install the rotation stop?

If the system includes a delivery system and support center, install the rotation stop for the system’s type of chair. Instructions for installing the rotation stops ship with the stops. The rotation stop is required for the following chairs:

• A-dec 311lft/311B
• A-dec 411
• A-dec 511flt/511A/B, when the system includes any A-dec 300/300 Pro delivery system and a support center

---

How do I install the Support Link and Arm?

The support link and arm installation procedure is the same on an A-dec 311flt/311B, 411, 511A and 511flt/511B.

1. Use the touchpad, footswitch, or jumper to raise the chair base and chair back.
2. Position the support link and arm straight out from the chair.
3. Get four bolts and washers from the kit.
4. Attach the support link and arm to the chair with the four bolts and washers but only finger tighten the bolts.
5. Place a level on the support link.
6. Tighten the bolts to secure the support link while keeping it as level as possible.

---

How do I install the Support Center?

The support center installation procedure is the same on an A-dec 311flt/311B, 411, 511A and 511flt/511B.

1. Position the cuspidor so it faces and is aligned with the support arm.
2. Slide the support center down all the way onto the post.

NOTE: The support center umbilical routes outside of the post that the support center installs on.

---

How do I route the umbilical cord during the support center installation?

1. Route the umbilical through the support arm and link, then down the front of the lift arm. Be sure to go through the link and not underneath it.
2. Keep the wires and data line on the side of the support link and arm toward the power supply. Do not cross the tubing.

---

How do I connect the Wires and Data Line to an A-dec Universal Power Supply Manufactured After June 2023?

Recommended Tools:

• Diagonal cutters
• 3/8" combination wrench

1. Turn off the power to the system.
2. Attach the support center’s ground wire.
3. Connect the black wire to the support center 0 V.
4. Connect the gray wire to the support center 24 V.
5. Plug the data line into any DCS1 data port.
6. Once all of the electrical connections have been made for the system’s modules, secure the wires under the lip on the power supply.

CAUTION: Plugging the black DCS1 data line into a DCS2 port toward the toe of the chair can damage the product.

NOTE: Perform the next step only if all chair modules have been installed and all other electrical connections have been made. Otherwise, wait to perform this step until all other electrical connections to the power supply have been completed.

Next Step: Continue with “Connect the Tubing”.

---

How do I connect the Wires and Data Line to an A-dec 311/411 Power Supply Manufactured Before June 2023?

Recommended Tools:

• Diagonal cutters
• 3/8" combination wrench

1. Turn off the power to the system.
2. Attach the support center’s ground wire.
3. Connect the black wire to the support center 0 V.
4. Connect the gray wire to the support center 24 V.
5. Plug the data line into any data port.
6. Once all of the electrical connections have been made for the system’s modules, secure the wires under the lip on the power supply.

NOTE: Perform the next step only if all chair modules have been installed and all other electrical connections have been made. Otherwise, wait to perform this step until all other electrical connections to the power supply have been completed.

Next Step: Continue with “Connect the Tubing”.

---

How do I connect the Wires and Data Line to an A-dec 511 Power Supply Manufactured Before June 2023?

Recommended Tool:

• Phillips head screwdriver

1. Turn off the power to the system.
2. Attach the support center’s ground wire.
3. Connect the black wire to 0 V.
4. Connect the gray wire to 24 V.
5. Plug the data line into any data port.

NOTE: To connect more than one module to the 0 V and 24 V terminal strips, use the jumper wires and electrical connectors from the kit.

---

How do I connect the Tubing for Configurations that Include an A-dec 300 Delivery System?

Recommended Tools:

• Diagonal cutters
• Sleeve pusher

1. If the system includes a delivery system, strip and remove three feet of the sheath from around the water bottle tubing.
2. Connect the tubing according to the flow diagram.

NOTE: When installing the water manifold, be sure to connect to the barb on the end to prevent standing water in the manifold.

NOTE: Do not connect the blue or white tubing.

NOTE: If the system includes a CP5i control pad, the green tubing with a long dash is trimmed at the end of the sheaths and does not get connected.

---

How do I connect the Tubing for Configurations that Include an A-dec 500 Delivery System?

Recommended Tools:

• Diagonal cutters
• Sleeve pusher

NOTE: When cutting the tubing to length for the connections, be sure to leave enough room for the gravity drain to move a few inches without kinking.

Next Step: See “Install the Cuspidor”.

NOTE: If the system includes a DS7 touchscreen, the green tubing with a long dash is trimmed at the end of the sheaths and does not get connected.

---

How do I install the cuspidor?

1. Install the bail. It ships in the floor box kit.
2. Insert the cupfill spout.
3. Insert the bowl rinse spout.
4. Insert the bowl screen.

CAUTION: Do not rotate the cupfill spout or it may break.

---

How do I prepare and adjust the system?

1. Secure the Wires and Tubing

   Recommended Tool:

   • Diagonal cutters

2. Use cable ties to group the tubing and wiring for a neat appearance.

   CAUTION: Do not secure the tubing to the lift arm. The tubing needs to move freely when the chair moves.

3. Install the Water Bottle

4. Apply A-dec silicone lubricant on the receptacle O-ring.

5. Push the water bottle up onto the water bottle receptacle and turn it to the right.

IMPORTANT: A-dec recommends that the dental team perform a shock treatment on the dental unit waterlines before they use the system for the first time, and establish an ongoing waterline maintenance program.

---

How do I adjust the cuspidor bowl rinse settings?

1. Remove the support center cover.
2. Turn on the bowl rinse.
3. Tighten or loosen the pinch valve to adjust the flow.
4. To adjust the flow pattern and achieve the best rinsing action, rotate the bowl rinse spout.
5. To set the length of cupfill and bowl rinse flow, use the touchpad buttons.

---

How do I adjust the support arm rotation tension (optional)?

Recommended Tool:

• 1/8" hex key

1. Use a hex key to adjust the tension so that the arm moves smoothly but holds position when the cuspidor is moved. Clockwise increases the tension.

---

How do I align the support center?

1. Rotate the support center so that it is aligned with the dental chair.

---

How do I operate the cuspidor with a CP5i/CP5 Control Pad?

For touchscreen and control pad use, see the A-dec DS7/CP5i/CP5 Touch Controls Instructions for Use (p/n 86.0857.00) at a-dec.com/touchscreen-manual.

For configuring connectivity features, see the A-dec+™ Software Platform Instructions for Use (p/n 86.1030.00) at a-dec.com/connectivity-manual.

---

How do I operate the cuspidor with an A-dec 300 Deluxe/Standard Touchpad?

Turn On/Turn Off Cupfill and Bowl Rinse: Use the touchpad icons or the cuspidor buttons to control cupfill and bowl rinse functions.

Customize Cupfill and Bowl Rinse Timing: Cupfill and bowl rinse timing can be set at the touchpad or the cuspidor.

Customize Timing From the Touchpad:

1. Press and hold p on the touchpad. Release when you hear one beep.
2. Within five seconds, press and hold d or c for the desired amount of time.
3. Three beeps indicate the new setting is saved.

Customize Timing From the Cuspidor:

1. Press and hold and under the cupfill spout. Release when you hear one beep.
2. Within five seconds, press and hold or for the desired amount of time.
3. Three beeps indicate the new setting is saved.

Icon/Function	Actions/Options
Cupfill	Controls water flow from the cuspidor into a cup.
Touchpad	* Press once for a timed operation. The factory preset is a 2.5 second fill. * Press and hold for manual operation.
Cuspidor
Bowl Rinse	Provides rinse water for the cuspidor bowl.
Touchpad	* Press for a timed operation. The factory preset is a 30 second rinse. * Press twice for continuous flow, then press once to stop the flow. * Press and hold for manual operation. Release to stop the flow.
Cuspidor

---

How do I install the covers?

Install the Mount Cover:

1. Snap the slotted mount cover in place. The four posts go into the holes on the mount.

Install the Support Arm Cap:

Recommended Tool:

• 5/32" hex key

1. Use the 5/32" hex key to partially install the screw.
2. Slide the support arm cap onto the end of the arm. The screw goes into the slot in the cap.
3. Secure the cap.

Install the Bearing Cover (Optional):

This cap is only used with systems that do not include an assistant’s instrumentation.

Recommended Tool:

• 5/32" hex key

1. Secure the bearing cover to where the support link meets the support arm.

Install the Support Link Cover:

The support link cover installs the same way on all systems.

1. Snap the support link cover into place.

---

How do I test the system?

After you have completed the installation, use the following checklist to test the system, then follow up with the customer.

Utilities:

• Regulated air pressure to the delivery system is at 80 psi (552 kPa).
• Floor box is free of air and water leaks.
• The gravity drain functions properly.
• Tubing and connections are not kinked and are free of air and water leaks.
• Excess tubing and wires are coiled and stored away from moving parts.
• Cuspidor limit switch functions properly.

Cuspidor and Cupfill:

• Cupfill timing is set properly.
• Cuspidor flow pattern effectively rinses the bowl, bowl drains properly.