A-DEC 5562 (01) PDF MANUAL

• Hex key set
• Drill
• 1/2″ concrete drill bit (12″ long) or 3/8″ wood drill bit
• Ratchets (1/2″ and 3/8″ drive)
• 3/8″ x 4″ ratchet extension
• Impact driver

Check with local building and code authorities about installation requirements specific to your location.

Check that the manual air shut-off valve is installed.

• A-dec Inspire 391 Treatment Console Installation Guide (p/n 86.1068.00)
• A-dec Inspire 591 Treatment Console Installation Guide (p/n 86.0522.00)
• Preference Collection 5580 Treatment Console Installation Guide (p/n 86.0133.00)
• Preference Collection 5580.69 and 5580.96 Treatment Console Installation Guide (p/n 86.0199.00)
• Preference Collection 5562 Treatment Column Installation Guide (p/n 86.0136.00)
• Preference Collection 5662 Treatment Column Installation Guide (p/n 86.0137.00)

Locate and mark the mounting holes for drilling.

1. Drill 1/2″ (13 mm) diameter holes 2-3/4″ (70 mm) deep.
2. Remove debris from the holes.

TIP A 12″ long concrete drill bit is recommended to make it easier to drill inside the cabinet.

Install four 1/2″ x 4″ concrete studs into the holes and tighten the washers and nuts on the studs.

• Drill
• 3/8″ wood drill bit
• Ratchet (3/8″ drive)
• 3/8″ x 4″ ratchet extension

Locate and mark the mounting holes for drilling.

1. Drill 3/8″ (9.5 mm) diameter holes 3-1/4″ (83 mm) deep.
2. Remove debris from the holes.

Use four 1/2″ x 4″ lag screws and washers to secure the mount.

Ensure the doors and false bottom are not installed on the lower cabinet.

• 5/32″ hex key
• Phillips head screwdriver

1. Slide the mount housing bracket from the kit into the subbase.
2. Use a Phillips head screwdriver and the eight screws from the kit to attach the mount housing bracket to the subbase rails.

5/32″ hex key

1. Use a 5/32″ hex key to loosen the six adjustment screws on the inside of the mount housing bracket.
2. Slide the mount into the housing and align the holes in the mount with the holes in the housing plate.
3. Lower the housing plate so that it sits snugly on top of the mount.
4. Tighten the six adjustment screws on the inside of the mount housing bracket.

• 5/16″ hex key
• Impact driver

Use a 5/16″ hex key and four mounting screws from the hardware kit to secure the mount to the housing plate. Tighten the screws until snug.

TIP You may need to use an impact driver to fully tighten the screws.

Product Models and Versions Covered In This Document

*Some product models, versions, and options in this document may not be available in certain regions.

When testing is complete, install the left and right base covers, and then the corner covers.

To install the delivery system, follow the steps in the appropriate installation guide:

• A-dec 341pro/341flt Duo Delivery System Installation Guide (p/n 86.1064.00)
• A-dec 541 Duo Delivery System and 545 Assistant’s Instrumentation Installation Guide (p/n 86.0763.00)
• A-dec 541pro Duo Delivery System and 545sta Assistant’s Instrumentation Installation Guide (p/n 86.0946.00)

When installation is complete, check that the mount is flush with the floor and that all screws are fully tightened.

To mount a 341pro/341flt/541pro/ 545sta/541/545 system on a Preference Collection 5580 not containing subbase cutouts, order a new style subbase front and quantity (8) 012.004.00 pop rivets. Affected Preference Collection 5580 cabinets are those shipped before October 3, 2005.

Shock hazard. When you remove or replace the covers, take care not to damage any wiring or tubing. Verify that the covers are secure after you replace them.