70MAI OMNI X800-2 (01) PDF MANUAL

If you purchased the Dash Cam Set, check the following items in the package:

1. Dash Cam × 1

2. Power cord × 1

3. Car charger × 1

4. Mount (pre-installed on the dash cam) × 1

5. Adhesive sticker × 1

6. Electrostatic sticker × 2

7. Wiring trim tool × 1

8. User manual × 1

9. Rear camera package* × 1

* This package contains the rear camera (integrated with lead wire), rear camera wire and other accessories for the rear camera. For more information about the rear camera, please refer to the rear camera user manual.

If you purchased the dash cam only, check the following items in the package:

1. Dash Cam × 1

2. Power cord × 1

3. Car charger × 1

4. Mount (pre-installed on the dash cam) × 1

5. Adhesive sticker × 1

6. Electrostatic sticker × 2

7. Wiring trim tool × 1

8. User manual × 1

Mount the dash cam on either of the recommended positions of the front windshield as appropriate: ①. Near the center of rearview mirror; ②. On the front of the passenger seat.

Note: Make sure the camera is below the level line of the rearview mirror.

Attach the electrostatic sticker on the selected position, with the gap image facing upwards. Press the sticker to remove air bubbles out.

Avoid the edge of the windshield and select the flat and smooth area for the installation.

Note: Keep windshield clean and dry without liquid residue to prevent the sticker from losing adhesion and dash cam from dropping.

Insert the memory card into the slot.

Paste the dash cam on the electrostatic sticker. Make sure the gap on the adhesive sticker aligns with that on the electrostatic sticker and the display screen faces the car interior.

Connect the dash cam and car charger with the power cord.

Route the power cord to the vehicle’s power outlet and plug the car charger into the power outlet. Start the car engine, and the dash cam will automatically turn on.

Notes:

Use the included wiring trim tool to hide the power cord underneath the vehicle’s headliner and rubber seal along the A-pillar.

Depending on the vehicle, the power outlet may be located in a different position. The provided figure is for reference only.

Adjust the camera angle based on the image presented on the main screen when dash cam is turned on.

Hold the dash cam and screw it clockwise and then the dash cam will separate with the mount.

1. Align the microphone with the icon on the mount, and the dash cam is inserted into the mount.

2. Hold the dash cam and screw counterclockwise until the microphone is aligned with the icon on the mount, and then the dash cam is tightened up with the mount.

This product needs to be used in conjunction with the 70mai app. Follow the steps below to connect it with the app.

1. Scan the QR code to download and install the app. Or search for “70mai” in the app store to download and install it.

2. Open the app and tap “+” in the homepage. In the Bluetooth scanning result list, tap the dash cam’s name (same with the dash cam Wi-Fi name) and then confirm the authorization on the dash cam.

3. Follow the on-screen instructions to connect the dash cam Wi-Fi. When connected, the dash cam’s homepage displays. You can view the live video and configure the dash cam settings.

Notes:

Before binding, make sure that your phone is connected to the internet and Bluetooth is enabled.

Find the dash cam Wi-Fi name in the quick control panel.

During the binding process, please follow the instructions on the app screen to grant permissions.

Android 5.0 & iOS 12.0 or above is required to connect to the dash cam’s Wi-Fi hotspot with a mobile phone. As mobile phone operating systems continue to be updated, the minimum requirements for Android and iOS systems may also increase.

The rear recording function of this product needs to be used with a rear camera. Scan the QR code to obtain the user guide for the rear camera.

Note: To avoid the rear camera malfunction due to device incompatibility, it is recommended to use a rear camera from 70mai brand.

Dash cam supports voice control. When the dash cam is operating, voice commands from the user will trigger the corresponding functions.

The supported languages are English, Italian, Japanese and Mandarin (when the dash cam’s broadcast language is Traditional Chinese).

The voice commands are as follows:

Notes:

1. To use those voice commands, make sure a rear camera is installed and connected correctly with the dash cam.

2. The start position can be adjusted. Connect the dash cam with the 70mai app and adjust it in the dash cam settings, following the on-screen prompts.

3. When the dash cam is connected with the 70mai app, voice control is not supported.

Before using this dash cam, please read all the precautions and user guide to ensure correct and safe use.

This dash cam is a driving aid designed to record external images of the vehicle. And it does not have the function of ensuring the user’s driving safety. Users must abide by local traffic rules and regulations and take driving safety as a priority consideration. Do not operate this product while driving.

Due to differences in vehicle conditions, driving style, driving environment, and other factors, some functions may not work properly. A power failure, usage in environments outside the normal operating temperature or humidity range, a collision, or a damaged memory card may cause the dash cam to function abnormally. There is no guarantee that this dash cam will function normally under all circumstances. Videos recorded by this dash cam are for reference purposes only.

Please install this dash cam correctly, and do not block the driver’s line of sight, or block the vehicle’s airbag, in order to avoid product failure or personal injury.

If the front windshield where the dash cam is installed is covered with colored automotive film, it may affect the video recording quality or cause video distortion. If metallic film is applied to the front windshield, it may lead to a decrease in GPS signal quality for dash cam models equipped with built-in GPS modules.

Avoid collisions or forceful jolts to the dash cam, otherwise the product may malfunction. Keep this dash cam away from any strong magnetic fields.

Never use chemical solvent or detergent to wash the dash cam.

Do not use this dash cam in environments with temperatures over 60°C or below -10°C.

When the dash cam has been operating for a period of time, the temperature of the outer casing will rise, so use caution when touching it.

Please only use this dash cam within the scope permitted by law.

Please use the included car charger, power cord, and other accessories in order to avoid product failure due to non-conformance. We shall not be held liable for any loss or damage caused by the use of a non-genuine car charger or power cord.

If you use power adapter to charge the dash cam, only use the power adapters that comply with the local safety standards or certified and supplied by qualified manufacturers.

Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.

Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas.

A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.

This device is equipped with a built-in lithium metal battery that cannot be removed or replaced. Do not disassemble or modify the battery by yourself.

Replacement of a battery with an incorrect type can defeat a safeguard (for example, in the case of some lithium battery types).

The dash cam and its accessories may contain small parts. To avoid choking or other hazards or damages caused by the children, keep the dash cam out of the reach of children.

A memory card (sold separately) must be installed in the dash cam before use.

The dash cam supports standard microSD cards. Please use memory cards with capacity of 32GB ~ 512GB and rating of U3 (UHS-3) or higher.

The default file partition format of the memory card may be inconsistent with the format supported by the dash cam. When inserting the memory card for the first time, please format it in the dash cam before use. Formatting the memory card will delete all files on the card. Please back up important data to another device beforehand.

The memory card may become damaged or deteriorated after repeated cycles of overwriting, and this may affect its ability to save video and image files. If this occurs, immediately replace it with a new memory card.

Please use a high-quality memory card purchased from a reputable vendor. Inferior memory cards may have issues such as actual reading/writing speeds that do not match the stated speeds, and an actual storage capacity that does not match the stated storage capacity. We shall not be held liable for lost or damaged videos caused by the use of a low-quality memory card.

Do not insert or remove a memory card while the dash cam is turned on.