ZEPHYR RC-0003 (01) PDF Document

The ZEPHYR RC-0003 remote control contains a button cell or coin battery. It is an ingestion hazard, and death or serious injury can occur if ingested.

A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.

You must KEEP new and used batteries OUT OF REACH of CHILDREN.

Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.

Please follow these safety precautions for the ZEPHYR RC-0003 battery:

a) Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.

b) Even used batteries may cause severe injury or death.

c) Call a local poison control center for treatment information.

d) The compatible battery type is CR2032.

e) The battery voltage is 3V.

f) Non-rechargeable batteries are not to be recharged.

g) Do not force discharge, recharge, disassemble, heat above the manufacturer’s specified temperature rating, or incinerate. Doing so may result in injury due to venting, leakage, or explosion resulting in chemical burns.

h) This product contains non-replaceable batteries.

To synchronize your ZEPHYR RC-0003 remote with a current model range hood, please follow these steps. Current models include: DAP-M90Ax, DHZ-M90Ax, DLA-M90Ax, DLA-E42Ax, DME-M90Ax, DME-E48Ax, DVL-E36Ax, DVL-E42Ax, DVS-E30Ax, DVS-E36Ax, ZAM-E30AS, ZAM-E36AS, ZCO-E30AS, ZCO-E36AS, ZPO-E30AS, and ZPO-E36AS.

1. With the range hood off, press and hold the Power button on the hood for 4 seconds until the 3rd speed indicator on the hood flashes 3 times.

2. Press any button on the remote control within 4 seconds to confirm the link. The range hood is now synchronized with the remote control. If any problems are experienced, please repeat the procedure. The hood lights will turn on if the Lights button on the remote control was pressed to confirm the link.

NOTE: “x” within the model number represents a placeholder for different colors.

To synchronize your ZEPHYR RC-0003 remote with a previous model range hood, please follow these steps. Previous models include: AIN-M80Ax, AWA-M90Ax, ADL-M90Bx, ADL-E42Bx, ADU-M90Bx, ALA-M90Bx, ALA-E42Bx, ALL-M90Bx, ALL-E42Bx, and ALU-E43Ax.

1. With the range hood off, press and hold the Power and Delay Off buttons on the remote for 4 seconds until the Delay Off indicator on the hood illuminates.

2. Press the Delay Off button on the hood within 4 seconds to confirm the link. If successful, the Delay Off indicator on the hood will flash 3 times. The range hood is now synchronized with the remote control. If any problems are experienced, please repeat the procedure.

NOTE: “x” within the model number represents a placeholder for different colors.

Please follow the steps below to install the battery in your ZEPHYR RC-0003. The battery part number is 15000014.

1. Remove the rubber bottom.

2. Remove the two (2) screws from the bottom of the remote control.

3. Place a pen or screwdriver in the bottom opening to dislodge the top touch panel.

4. Install one (1) CR2032 battery and reassemble the remote body.

The maximum remote control communication distance for the ZEPHYR RC-0003 is 15 feet from the range hood. The remote control is also equipped with a magnetic base and may be attached to a ferrous surface for easy storage.

Power Button: Press the Power Button to turn off the fan and lights.

Fan Button: Press the Fan Button to cycle through low, medium, and high speeds.

Lights Button: Press the Lights Button to cycle from high, medium, low, and off. Models ZAM and ZCO only have two light levels, high and low.

Delay Off Button: Press the Delay Off Button to enable the delay off timer. After a period of time, the fan and lights will turn off. The timer is 10 minutes for current models and 5 minutes for previous models.