Free English DRUCK UPS4E (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD DRUCK UPS4E (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What are the product categories for the DRUCK UPS4E under EU WEEE and UK WEEE regulations?
| Regulation | Category | Description |
|---|---|---|
| EU WEEE (2012/19/EU) | 5 | Small Equipment |
| UK WEEE (UK SI 2013/3113) | 9 | Monitoring and control Instruments |
What do the color codes in the DRUCK UPS4E recycling guide signify?
| Color Code | Materials Category |
|---|---|
| Red | To be removed and treated separately |
| Green | Part of the product |
| White | Referenced item |
How do I perform the main assembly breakdown of the DRUCK UPS4E for recycling?
The following table details the main components of the DRUCK UPS4E for recycling breakdown:
| No. | Recycling/Material-Code | Important Information |
|---|---|---|
| 1 | Front Case Assembly | Remove as one piece. See Section 3.2 |
| 2 | Rear Case Assembly | Remove as one piece. See Section 3.3 |
| 3 | Screws | Stainless steel |
| 4 | Batteries | Alkaline batteries |
| 5 | Battery Cover | Polycarbonate/ABS Alloy (PC/ABS) |
How do I break down the front assembly of the DRUCK UPS4E for recycling?
The front assembly of the DRUCK UPS4E consists of the following components:
| No. | Recycling/Material-Code | Important Information |
|---|---|---|
| 1 | Front Display Assembly | Polycarbonate/ABS Alloy (PC/ABS) – Glass & LCD |
| 2 | Keypad | Silicon rubber |
| 3 | PCB Assembly | PCB Assembly |
| 4 | O-rings | Nitrile |
| 5 | Socket PCB | PCB Assembly |
| 6 | Screws | Stainless Steel |
| 7 | Screws | Stainless Steel |
| 8 | PCB Protecting Sheet | Polycarbonate film |
| 9 | Screws | Stainless Steel |
How do I break down the rear assembly of the DRUCK UPS4E for recycling?
The rear assembly of the DRUCK UPS4E consists of the following components:
| No. | Recycling/Material-Code | Important Information |
|---|---|---|
| 1 | Rear Plastic Molding | Polycarbonate/ABS Alloy (PC/ABS) |
| 2 | Spring Clips | Beryllium Copper |
| 3 | USB Protection Sheet | Nomex Type 410 Thermal Insulating Sheet |
What is the recycling data for the DRUCK UPS4E, including component weights?
The approximate weights of the components for recycling the DRUCK UPS4E are as follows:
Material/Components that must be removed and treated separately
| Recycling/Material-Code | Weight (approx., in kilograms) |
|---|---|
| PCB | < 0.11 |
| Batteries | < 0.1 |
| Subtotal | <0.21 |
Materials/Components that are part of the product
These components include the Case (Front plastic, Display glass, Rear assembly), Inserts, and Fixings (including screws, O-rings). Refer to Section 3 for breakdown instructions.
| Total Weight | 0.318 |
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD DRUCK UPS4E (01) PDF DOCUMENT