Free English ZALMAN S5 NEO (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD ZALMAN S5 NEO (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What should I do before installing the ZALMAN S5 NEO?
Read this manual carefully before installing the ZALMAN S5 NEO.
What should I do if I find an abnormality with the ZALMAN S5 NEO product or components before installation?
Check the product and components before installing. If you find any abnormality, contact the location where you purchased the product for a replacement or refund.
What should I wear when installing the ZALMAN S5 NEO?
Wear gloves to prevent accidents when installing the product.
What should I be careful about when mounting the system for the ZALMAN S5 NEO?
Severe damage may occur when mounting the system, so do not apply excessive force.
What can happen if the cable is connected incorrectly for the ZALMAN S5 NEO?
Connecting the cable incorrectly may cause a fire due to a short circuit. Make sure to refer to the manual when connecting the cable.
What should I be careful about when using the ZALMAN S5 NEO system?
Be careful not to block the ventilation hole of the product when using the system.
Where should the ZALMAN S5 NEO product be stored and used?
Avoid locations with direct sunlight, water, moisture, oil, and excessive dust. Store and use the product in a well-ventilated location.
What should I avoid using to wipe the surface of the ZALMAN S5 NEO product?
Do not wipe the surface of the product using chemicals. (organic solvents such as alcohol or acetone)
What should I avoid doing during the operation of the ZALMAN S5 NEO?
Do not insert your hand or other object into the product during operation, as this may injure your hand or damage the object.
Where should the ZALMAN S5 NEO product be stored in relation to children?
Store and use the product out of children’s reach.
What is the company’s responsibility regarding the use of the ZALMAN S5 NEO product?
Our company assumes no responsibility for any problem that occurs due to the use of the product for purposes other than its designated purposes and/or the carelessness of the consumer.
Are there any potential changes to the exterior design and specifications of the ZALMAN S5 NEO product?
The exterior design and specifications of the product are subject to change without prior notice to consumers for quality improvement.
What are the specifications for the ZALMAN S5 NEO case?
The specifications for the ZALMAN S5 NEO are as follows:
| Item | Specification |
|---|---|
| Model | S5 NEO |
| Case Form Factor | ATX Mid Tower |
| Dimensions | 456(L) x 215(W) x 490(H)mm |
| Weight | 7.5kg |
| Case Materials | Plastic, Steel, Tempered Glass |
| Motherboard Support | ATX, mATX, Mini-ITX |
| Maximum VGA Length | 390mm |
| Maximum CPU Cooler Height | 165mm |
| Maximum PSU Length | 160mm |
| PCI Expansion Slots | 7 |
| Drive Bays | 2 x Combo(3.5″ or 2.5′) / 2 x SSD (2.5″) |
| Fan Support | Front: 3 x 120mm / 3 x 140mm, Side: 2 x 120mm, Top: 3 x 120mm / 2 x 140mm, Rear: 1 x 120mm, Bottom: 2 x 120mm |
| Fan(s) Included | Front: 3 x 120mm (RGB Fan), Top: 1 x 120mm (RGB Fan), Rear: None, Bottom: None |
| Radiator Support | Front: 120mm/140mm / 240mm / 280mm / 360mm, Top: 120mm/140mm / 240mm / 280mm / 360mm, Rear: 120mm |
| I/O Ports | Power, Power LED, Reset, HD Audio, 1 x USB 3.0, 1 x USB2.0, HDD LED |
What are the accessories included with the ZALMAN S5 NEO?
The accessories component for the ZALMAN S5 NEO includes:
User’s Manual
Cable Ties x 5
Glass Cleaner
PCI Slot Cover x 2
Thumb Screws x 2
SSD / MB Screws x 22
HDD Screws x 8
PSU / VGA Screws x 6
Motherboard Standoffs x 8
Motherboard Standoffs x 4
How do I remove the side panels of the ZALMAN S5 NEO?
To remove the side panels of the ZALMAN S5 NEO, locate the securing mechanism (usually thumb screws or latches at the rear) and slide or pull the panel off as indicated by the diagram.
How do I remove the front panel of the ZALMAN S5 NEO?
To remove the front panel of the ZALMAN S5 NEO, carefully pull the panel away from the chassis, usually starting from the side or bottom edge, as it is typically held on by clips.
How do I install the motherboard in the ZALMAN S5 NEO?
Step 1: Install the Motherboard Standoffs into the chassis at the locations corresponding to your motherboard size (ATX, mATX, or Mini-ITX).
Step 2: Place the motherboard onto the standoffs, aligning the screw holes.
Step 3: Secure the motherboard using the SSD / MB Screws.
How do I install the graphic card in the ZALMAN S5 NEO?
Step 1: Remove the necessary PCI Slot Covers from the rear of the chassis corresponding to the slot you will use for the graphic card.
Step 2: Insert the graphic card into the appropriate PCI-E slot on the motherboard.
Step 3: Secure the graphic card to the chassis using the VGA Screw.
What are the different methods for installing 2.5″ and 3.5″ SSD / HDD in the ZALMAN S5 NEO?
There are several methods for installing 2.5″ and 3.5″ SSD / HDD in the ZALMAN S5 NEO:
Method 5-1: Install the drive onto the mounting bracket/tray (if applicable) and then secure the assembly into the designated area using HDD Screws or SSD / MB Screws as shown.
Method 5-2: Install the drive directly into a designated mounting location using SSD / MB Screws.
Method 5-3: Install the PSU first (Section 6), then mount drives onto the drive cage/mounts located near the PSU area, securing them with PSU / VGA Screws or Thumb Screws as indicated.
How do I install the PSU in the ZALMAN S5 NEO?
Step 1: Insert the Power Supply Unit (PSU) into the designated compartment at the bottom rear of the chassis.
Step 2: Secure the PSU to the chassis using the PSU / VGA Screw from the rear of the case.
What are the radiator installation options for the ZALMAN S5 NEO?
Radiator installation options for the ZALMAN S5 NEO are:
Installing the front radiator: Supports 120mm/240mm / 280mm / 360mm.
Installing the top radiator: Supports 120mm/240mm / 280mm / 360mm.
Installing the rear radiator: Supports 120mm.
What are the fan mounting options for the ZALMAN S5 NEO?
The fan mounting options for the ZALMAN S5 NEO are:
Installing the Front fans: 3 x 120mm / 3 x 140mm.
Installing the Top fans: 3 x 120mm / 2 x 140mm.
Installing the side fans: 2 x 120mm.
Installing the rear / bottom fans: 1 x 120mm / 2 x 120mm respectively.
What are the I/O connectors on the ZALMAN S5 NEO?
The I/O Connectors on the ZALMAN S5 NEO include:
Power SW
Power LED
Reset SW
HD Audio
USB 3.0
USB 2.0
HDD LED
CLICK HERE TO DOWNLOAD ZALMAN S5 NEO (01) PDF DOCUMENT