YUPOSL MUSHROOM YPF02 (01) PDF MANUAL

Automatic Pet Feeder x1

Stainless Steel Bowl x1

Bowl Tray x1

Desiccant x1

User Manual x1

Power Adapter x1

Power Cable x1

1: Desiccant Holder

2: Lid Release Button

3: Lid

4: Food Tank

5: Tank Release Button

6: Indicator

7: LCD Display

8: Operation Panel

9: Food Outlet

10: Base

11: Stainless Steel Bowl

12: Bowl Tray

13: Cable Slot

14: Power Port

15: Battery Compartment

16: Battery Cover

17: Anti-skid Pad

Meal Number: Shows which meal setting is being displayed (1-6).

Locked Icon: A padlock icon indicates the operation panel is locked.

Low Battery: A battery icon indicates low battery power.

Food Blockage: A food bowl icon with an ‘X’ indicates a food blockage.

Time or Portion: The main digits show either the time (HH:MM) or the portion size (P-XX).

AM/PM: Indicates whether the set time is before noon (AM) or after noon (PM).

To reset the feeder, in the unlocked state, press the Unlock/Return button and the OK/Setting button simultaneously for 3 seconds until all icons on the screen light up, the resetting is complete.

1. Press the release button to open the lid, put in the desiccant bag.

2. Add food to the tank.

3. Lock the lid securely.

4. Install the stainless steel bowl and bowl tray.

Power on (Dual Power Modes)

1. Connect the power cable and install the batteries as a backup in case of power cuts.

2. The feeder can run on batteries alone.

Power off

Unplug the power cable and remove the batteries.

Note: The feeder can work well only when the time of the feeder is consistent with the current time.

1. After the feeder is powered on, press and hold the Setting Button for about 3 seconds, the hour digit flashes, press the Up/Down button to set the hour and then press the Setting Button to confirm.

2. The minute digit flashes, press the Up/Down button to set the minute and then press the Setting Button to confirm.

3. The AM icon flashes, press the Up/Down button to choose AM or PM, press the Setting Button to confirm, the current time setting is complete.

1. Setting the Feeding Time

After the current time is set, you can set the feeding time of the first meal. The meal number 1 and the hour digit flash simultaneously, press the Up/Down button to set the feeding time of the first meal, choose AM or PM and then press the Setting button to confirm.

2. Setting the Feeding Portion

After the feeding time is set, you can set the feeding portion of the first meal. The meal number 1 and the portion digit flash simultaneously, press the Up/Down button to set the feeding portion of the first meal, and then press the Setting button to confirm. The feeding plan of the first meal is set, repeat the above steps to set meal 2-6.

Notes:

1. Up to 6 meals can be set.

2. The maximum portion per meal is 16.

The per portion size is 1/24 cup (10.4ml).

1. Remove the food tank, stainless steel bowl and bottom tray.

2. Rinse the food tank and stainless steel bowl, detergent can be used, wipe dry or air dry the parts before use.

3. Do not wash the base with water, use a dry or wet cloth to clean.

Notes:

1. Unplug before cleaning.

2. Do not wash or soak the feeder base in water, as the base contains electronic components.

3. To keep food from moisture, air dry or wipe dry all parts after cleaning.

4. For the health of pets, rinse it thoroughly if detergent is used for cleaning.

5. To keep food fresh, replace the desiccant once a month.

Model YPF01

Model YPF02

The screen is likely locked. Press and hold the Unlock Button for 3 seconds to enter the setting mode.

In the locked status, press the + or – (Up/Down) buttons to check the settings of each meal.

1) Please make sure the food in the tank is dry, and food size is within 2-15 mm/0.07-0.6 inches in diameter.

2) Check if the chute inside is blocked. If blocked, remove the food tank, and then remove the blockage.

3) Check whether the battery level is low, whether the power adapter is connected, whether a power outage occurs when the power adapter is connected and batteries are not installed.

The first few portions may vary, but it doesn’t mean it’s faulty. After about 6 feedings, it should be almost even.

• Dispose of all packaging materials properly. Some items may be packed in plastic bags; these bags could cause suffocation. Keep them away from children and pets.

• Do not use the feeder with pets that are not able to reach the food tray or with any physical disability.

• Do not immerse the base part in water at any time as it may damage electronic components like the control panel.

• Do not use the feeder outdoors. Check its operation frequently to be sure it is dispensing properly.

• Do not use wet, canned or moist food.

• Do not disassemble the feeder other than as instructed in this user manual.

• Only use accessories recommended or sold by the manufacturer. The use of accessories not recommended or sold by the manufacturer may cause an unsafe condition.

• Do not modify the pet feeder.

• Examine the feeder after installation. Do not plug in if there is water on the power cable or plug.

• To avoid tripping, always position the power cable out of the way of foot traffic.

• Do not install or store the pet feeder where it will be exposed to weather or temperatures below 4°C (39.2°F).

• Use D alkaline batteries to power the feeder. Do not use rechargeable batteries.

• Check the batteries regularly. Before leaving for an extended period of time, always replace batteries with new ones.

• Do not lift the pet feeder by the lid, food tank, or food bowl. Lift and carry it using both hands and the base, while keeping the feeder in an upright position.

• Suitable for dry food only, with kibble sizes ranging from 2-15mm (0.07-0.6in) in diameter. Larger kibble may get stuck at the food outlet.

• Do not put your fingers into the food outlet or let your fingers touch the rotor.

• Power off the device when it’s not in use.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

• This device and its antenna(s) must not be co-located or operated in conjunction with any other antenna or transmitter.

Radio frequency exposure statement

To maintain compliance with the FCC’s RF Exposure Guidelines, this equipment should be installed and operated with a minimum distance of 20cm from your body.