Free English XIGMATEX HERO II AIR (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD XIGMATEX HERO II AIR (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
What is included in the accessory pack for the XIGMATEX HERO II AIR?
| x 12 | Motherboard Screw & 2.5″ Drive Screw |
| x 4 | 3.5″ Drive Screw |
| x 6 | Power Supply Screw |
| x 2 | Motherboard Stand-off |
What are the main features of the XIGMATEX HERO II AIR case?
The main features of the XIGMATEX HERO II AIR case are:
A: Front Side Panel
B: Left Tempered Glass Panel
C: Right Side Panel
D: Front I/O Panel (HD Audio, USB 3.0 x2, Type C x1)
E: Power Button, Reset Button
F: Dust Filters
How do I remove the side panels on the XIGMATEX HERO II AIR?
To remove the side panels on the XIGMATEX HERO II AIR, unscrew the thumbscrews located at the corners of each panel. Once the screws are removed, you can pull the panels away from the main chassis.
What motherboard form factors are compatible with the XIGMATEX HERO II AIR?
The XIGMATEX HERO II AIR is compatible with ATX, M-ATX (Micro-ATX), and M-ITX (Mini-ITX) motherboard form factors.
How do I install a motherboard in the XIGMATEX HERO II AIR?
First, install the motherboard stand-offs into the chassis according to your motherboard’s form factor (ATX, M-ATX, or M-ITX). Carefully place your motherboard into the case, aligning the mounting holes with the installed stand-offs and ensuring the rear ports fit through the I/O shield opening. Finally, secure the motherboard to the stand-offs using the provided motherboard screws.
How do I install a graphics card in the XIGMATEX HERO II AIR?
To install a graphics card, first identify the correct PCI-e slot on your motherboard. Remove the corresponding expansion slot cover(s) from the back of the XIGMATEX HERO II AIR case. Align the graphics card’s connector with the motherboard’s PCI-e slot and press down firmly until the card is fully seated. Secure the graphics card’s mounting bracket to the case with a screw.
How do I install a power supply in the XIGMATEX HERO II AIR?
The power supply unit (PSU) is installed in the bottom rear section of the XIGMATEX HERO II AIR case. Slide the PSU into the compartment from the side of the case. Align the screw holes on the back of the PSU with the corresponding holes on the rear of the chassis. Secure the PSU in place using the provided power supply screws.
How do I install 3.5-inch and 2.5-inch drives in the XIGMATEX HERO II AIR?
The XIGMATEX HERO II AIR provides several mounting locations for storage drives. You can install 3.5-inch hard drives or 2.5-inch SSDs/hard drives in the drive cage located in the bottom shroud. There are also dedicated mounting points for 2.5-inch drives on the back of the motherboard tray. Use the appropriate screws from the accessory pack to secure your drives in the desired locations.
What are the fan installation options for the XIGMATEX HERO II AIR?
The XIGMATEX HERO II AIR supports the following fan configurations:
Top: Up to two 120mm fans or two 140mm fans.
Front: Up to three 120mm fans.
Rear: One 120mm fan.
What are the liquid cooling radiator options for the XIGMATEX HERO II AIR?
The XIGMATEX HERO II AIR supports the following liquid cooling radiator sizes:
Top: Up to a 360mm radiator (with a total length less than 400mm).
Rear: One 120mm radiator.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
CLICK HERE TO DOWNLOAD XIGMATEX HERO II AIR (01) PDF DOCUMENT