WORX WX317 (01) PDF Document

Free English WORX WX317 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.

CLICK HERE TO DOWNLOAD WORX WX317 (01) PDF DOCUMENT

If this is not the document you want for this product, click here to see if we have any other documents for this product.

How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.

What is the intended use for the WORX WX317 impact drill?

The WORX WX317 machine is intended for impact drilling in brick, concrete and stone as well as for drilling in wood, metal and plastic.

What are the steps for clamping and loosening the auxiliary handle on the WORX WX317?

Refer to Figure A1, A2 for clamping and loosening the auxiliary handle.

WARNING! Always check and rotate the handle tightly before using to avoid any accident.

How do I install the Depth Gauge on the WORX WX317?

Refer to Figure B for installing the depth gauge.

How do I insert bits into the chuck of the WORX WX317?

Refer to Figure C1, C2 for inserting bits into the chuck.

How do I plug in the power for the WORX WX317?

Refer to Figure D for plugging in the power.

How is the On/Off Switch and Lock-on Button operated on the WORX WX317?

Refer to Figure E for the On/Off Switch and Lock-on Button.

How is the Variable Speed Control adjusted on the WORX WX317?

Refer to Figure F for the Variable Speed Control.

How is the Forward and Reverse Rotation Control set on the WORX WX317?

Refer to Figure G for the Forward and Reverse Rotation Control.

NOTE: Never move the forward/reverse switch whilst the drill in operation or the on/off switch is locked as this will damage the drill.

How is the Hammer or Drilling Control selected on the WORX WX317?

Refer to Figure H for the Hammer or Drilling Control.

What steps should be taken when drilling masonry and concrete with the WORX WX317?

Select the drill/impact action selector switch to the “hammer symbol” position.

Tungsten carbide drill bits should always be used for drilling masonry, concrete etc with a high speed.

What steps should be taken when drilling steel with the WORX WX317?

Select the drill/impact action selector switch to the “drill symbol” position.

HSS drill bits should always be used for drilling steel with a lower speed.

What is recommended when drilling a large hole in tough material (i.e. steel) with the WORX WX317?

It is recommended to drill a small pilot hole first before using a large drill bit.

How should the WORX WX317 be used for drilling tiles?

Select the drill/impact action selector switch to the “drill symbol” position to drill the tile.

When the tile has been penetrated, switch over to the “hammer symbol” position.

What should be done if the motor of the WORX WX317 becomes too hot?

Set the speed to maximum and run no load for 2-3 minutes to cool the motor.

What maintenance is required for the WORX WX317?

Remove the plug from the socket before carrying out any adjustment, servicing or maintenance.

The WORX WX317 requires no additional lubrication or maintenance.

There are no user serviceable parts in the power tool.

Never use water or chemical cleaners to clean the power tool. Wipe clean with a dry cloth.

Always store the power tool in a dry place.

Keep the motor ventilation slots clean.

Keep all working controls free of dust.

Occasionally, sparks may be seen through the ventilation slots. This is normal and will not damage the power tool.

If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

If the replacement of the supply cord is necessary, this has to be done by the manufacturer or his agent in order to avoid a safety hazard.

What should be checked if the WORX WX317 power tool does not start?

Check the plug on the power supply first.

What should be checked if the drill bit of the WORX WX317 doesn’t work properly?

Check the drill bit for sharpness; replace the drill bit if worn.

Check that the drill is set to forward rotation for normal use.

What should be done if a fault on the WORX WX317 cannot be rectified?

Return the tool to an authorized dealer for repair.

What are the technical specifications for the WORX WX317?

The technical data for the WORX WX317 is as follows:

Parameter	Value
Voltage	230-240V~50Hz
Power input	600W
No load speed	0-3000/min
Impact rate	0-48000/min
Chuck capacity	13mm
Drilling capacity	Masonry	13mm
	Wood	25mm
	Steel	13mm
Protection class	I/II
Machine weight	2.1kg

What are the Noise/Vibration Information values for the WORX WX317?

The Noise/Vibration Information for the WORX WX317 is as follows:

Measurement	Value
A weighted sound pressure	LpA: 99dB(A)
A weighted sound power	LWA: 110dB(A)
KDA & KWA	3.0dB(A)
Wear ear protection when sound pressure is over	80dB(A)

What are the Vibration total values for the WORX WX317 determined according to EN 60745?

The Vibration total values for the WORX WX317 determined according to EN 60745 are:

Measurement	Value
Impact drilling into concrete Vibration emission value	ah ID= 6.435m/s²
Uncertainty K= 1.5m/s²
Drilling into metal Vibration emission value	ah D = 4,046m/s²
Uncertainty K= 1.5m/s²

What accessories are included with the WORX WX317?

The included accessories for the WORX WX317 are:

Accessory	Quantity
Auxiliary handle	1
Depth gauge	1

What are the general safety instructions for the WORX WX317 impact drill?

1. Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.

2. Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.

3. Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

What safety precautions should be taken before any work on the WORX WX317 machine itself?

Before any work on the machine itself, pull the mains plug from the socket outlet.

What is the warning regarding hand-arm vibration syndrome for the WORX WX317?

This tool may cause hand-arm vibration syndrome if its use is not adequately managed.

What should always be used to help minimise vibration exposure risk with the WORX WX317?

ALWAYS use sharp chisels, drills and blades.

How should the WORX WX317 tool be maintained?

Maintain this tool in accordance with these instructions and keep well lubricated (where appropriate).

If the tool is to be used regularly then invest in anti vibration accessories.

Avoid using tools in temperatures of 10°C or less.

Plan your work schedule to spread any high vibration tool use across a number of days.

What is the warning regarding accurate estimation of exposure level when using the WORX WX317?

To be accurate, an estimation of exposure level in the actual conditions of use should also take account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle but not actually doing the job. This may significantly reduce the exposure level over the total working period.