Post questions, comments, reviews or errors in the comment box below.
Your File is Ready … Download PDF
PDF Content Summary: Buttons OK Function Selection Up/Down Enter the menu/Confirm the setting Go back to the previous menu 1 2 6 34 1 1 2 Landroid®M - Auto mowing time schedule. Area Auto mow- sq.ft ing runtime - hours Monday Tuesday Wednesday Thursday Friday Saturday Sunday mowing mowing mowing mowing mowing mowing mowing hours hours hours hours hours hours hours 1000 3 9:00-10:30 / / 9:00-10:30 / / / 2000 7 9:00-10:24 9:00-10:24 9:00-10:24 9:00-10:24 9:00-10:24 / / 3000 8 9:00-10:36 9:00-10:36 9:00-10:36 9:00-10:36 9:00-10:36 / / 4000 11 9:00-11:12 9:00-11:12 9:00-11:12 9:00-11:12 9:00-11:12 / / 5000 13.5 9:00-11:42 9:00-11:42 9:00-11:42 9:00-11:42 9:00-11:42 / / 6000 16.5 9:00-12:18 9:00-12:18 9:00-12:18 9:00-12:18 9:00-12:18 / / 7000 19 9:00-12:48 9:00-12:48 9:00-12:48 9:00-12:48 9:00-12:48 / / 8000 21.6 9:00-13:18 9:00-13:18 9:00-13:18 9:00-13:18 9:00-13:18 / / 9000 24.3 9:00-13:54 9:00-13:54 9:00-13:54 9:00-13:54 9:00-13:54 / / 10000 27 9:00-14:24 9:00-14:24 9:00-14:24 9:00-14:24 9:00-14:24 / / Areas Area 1 Area 2 Distance from the charging base d1 ft d1+d2 ft Areas Area 1 Area 2 Area 3 Area 4 Distance from the charging base d1 ft d1+d2 ft d1+d2+d3 ft d1+d2+d3+d4 ft Funct Error Function messages Cutting grass according to the program setting. When it senses rain, Landroid®M will return to the Charging Base and stay there for the time you have programmed it to do so. When dry, Landroid®M will automatically begin the delay and countdown and then return to mow. If you want Landroid®M to mow before this, simply turn it off then on again, but only when the rain sensor is dry or you can set the delay time to 0 min. Needs to recharge—during the journey to the base, the cutting blade is stopped in order to save energy. Charge is in progress—charge percentage are displayed. Stand-by, will start according to program set. According to the setting of “Customize work area”, Landroid®M is searching a certain area to mow. Landroid®M has completed its charging. Error messages1. If Landroid®M is actually outside its territory: turn power off, take the Landroid®M inside its territory. Turn power on. 2. If the Landroid®M is inside its territory, check the LED on the charging base is green. If not, check the charging base is connected properly to the charger and the charger is connected to a suitable power supply. If so, it means that the boundary wire ends are clamped incorrectly, and you need to reverse them. 3. If the LED light flashes green, check the boundary wire is well connected to the clamps to the charging base. If the problem persists, check that the boundary wire hasn’t been cut. Refer to the "Programming" section to re-set your PIN. 1. Turn power off. 2. Turn Landroid®M upside down and check if there’s anything preventing the blade disc to rotate. 3. Remove any possible obstruction. 4. Turn Landroid®M upright and take it to an area with short grass or adjust the cutting height. 5. Turn power on. 1. Turn power off: take Landroid®M in an area free from obstacles. 2. Turn power on. 3. If the error message is still displayed; turn power off; turn Landroid®M upside-down and check if there’s anything preventing the wheels from rotating. 4. Remove any possible obstruction, turn Landroid®M upright, turn power on. 1. Turn power off. 2. Take Landroid®M to a lawn area free from obstacles. 3. Turn power on. 4. If the error message is still displayed; turn power off; turn Landroid®M upside-down and check if there’s any debris causing a blockage in the top cover. 5. Remove any possible obstruction, turn the Landroid®M upright, turn power on. 1. Turn power off. 2. Take Landroid®M to a lawn area clear of obstacles, turn power on. 3. If the error message is still displayed: turn power off, turn Landroid®M upside-down and check there’s nothing lifted up. 4. Remove any possible object, turn Landroid®M upright, turn power on. 1. Turn Landroid®M upright. 2. If still not work, Firstly, position the mower on a horizontal surface. Press Key “2” to enter the diagnosis interface, and press Key “5” for a few seconds until the three numbers 1 2 & 3 highlighted below turn back to zero. (See Fig. A) A 1. The contact between the Charging and Contact Pins may be obstructed in some way. 2. Wipe off the Charging and Contact Pins, making sure there is not an object obstructing them, then place your Landroid®M in the charging base and check that the Pins make good connection. 1. This means that there is low battery voltage. 2. In this case you must turn Landroid®M off and place it in the Charging Base, then “charging” will be shown on screen, which means it starts charging. A 112 2 3 3 Fault symptoms If your Landroid®M does not work correctly, follow the trouble shooting guide below. If the fault persists, contact your dealer. Refer to the Owner's Manual for Landroid®M component information. Symptom Cause Action Landroid®M turns on, but the Blade Disc does not move. Landroid®M is searching for the Charging Base (except that you press the HOME button to make it go to the charging base, or the “Enable boundary cut” function is operating). This is normal, Landroid®M needs to recharge, the Blade Disc does not rotate while it is searching for the Charging Base automatically. Landroid®M vibrates. Blades may be damaged. Check condition of the Blade Disc. Check the Blades, and replace them if damaged . Remove debris and foreign objects from the blades and blade disc. Grass is being cut unevenly. Landroid®M does not work enough hours per day. Add more hours to the mowing time. Mowing area is too big. Try decreasing the size of the mowing area or adding more hours to the mowing time. Blades are dull. Change all the Blades and screws in order to balance the Blade Disc. The cutting height is set too low for the length of the grass. Raise the cutting height and then gradually lower. Grass or other object has wrapped around the blade disc. Check the Blade Disc and remove the grass or other object. There is a build-up of grass in the Blade Disc or Motor Frame Box. Make sure the Blade Disc rotates easily. If needed, you may take off the Blade Disc and then remove the debris. See How to Clean. The LED light on the Charging base does not turn on. There is no power. Check the power cord is connected properly to the charger and the charger is connected to a suitable power supply. Green light flashing on charging base. The Boundary Wire isn’t connected. Check the boundary wire has been connected correctly to the charging base. Check there are no breaks in the boundary wire. Your Landroid®M is inside its territory but the display says “outside working area” and the LED is green. The boundary wire ends are clamped incorrectly. Reverse the boundary wire ends. The charging time is far more than 2h. Poor connection caused by debris on the Charging Strip. Clean the Contact Pins located on the Charging Base and the Charging Strip on Landroid®M using a cloth. The charging protection program has activated due to high temperature. Place the charging base in a shady area or wait until the temperature has cooled down. The mower does not charge. There is no power. Check the power cord is connected properly to the charger and the charger is connected to a suitable power supply. Does not operate correctly while manually charging. Refer to manual charging in Owner’s manual. Landroid®M is starting to have shorter run-times between charges. Something is clogged in the Blade Disc. Take off the Blade Disc and clean it. The grass is too high and too thick. Landroid®M is shaking heavily. Check the blade disc and blades, remove debris and foreign objects from the blades and blade disc. The battery may be exhausted or old. Replace battery. Landroid®M is not operating at the correct time. The clock is not set to the correct time. Set the clock to the correct time. Programmed cutting times for Landroid®M are not correct. Change the time settings for the mower to start and stop. Landroid®M can not correctly dock with the Charging Base. Environmental influences. Restart Landroid®M. Poor connection caused by debris on the Charging Strip. Clean the Contact Pins located on the Charging Base and the Charging Strip on Landroid®M using a cloth The Green light on the Charging Base turns ON before charging is complete. The charging base is overheating, the LCD will display “Over temperature”. Place the charging base in a shady area or wait until the temperature has cooled down. Landroid®M runs outside the boundary wire. Landroid®M does not mow an area within a boundary wire zone. Landroid®M reverses or rotates erratically near the boundary wire. The boundary wire of another Landroid®M or another branded robotic mower is positioned too closely. Ensure your Landroid®M Boundary Wire has at least 1.5ft (0.5m) of spacing between the neighboring boundary wire. The boundary wire has been installed with tight corners. Check the boundary wire to ensure the corners are smooth. In wet conditions, the boundary wire electric signal may leak were wire has been joined or repaired. Check boundary wire joints. Insulate to provide a fully waterproof connection. There is boundary wire electric signal leakage due to broken insulation. Repair damaged boundary wire insulation with insulation tape. The cutting area is larger than the allowable cutting area for Landroid®M. Contact service agent. Landroid®M wheels skid or damage lawn. Foreign obstacles, such as twigs and branches may be lodged under Landroid®M. Remove foreign objects from underside of Landroid®M. The lawn is too wet. Wait until lawn has dried. Landroid®M exits the boundary wire due to high speed when going down a hill. The Boundary Wire is placed on a slope steeper than 25%(15°). Reposition the Boundary Wire away from slopes that are steeper than 25%(15°). Please refer installation manual for details.
FREE ENGLISH PDF
USER GUIDE - USER MANUAL
OWNER GUIDE - OWNER MANUAL
REFERENCE GUIDE - REFERENCE MANUAL
INSTRUCTION GUIDE - INSTRUCTION MANUAL