WISBERG WBVR170NFE (01) PDF Document

To install your WISBERG WBVR170NFE, follow these steps:

1. Unpack the appliance, remove all packaging materials, and check for damage. Do not connect if damaged.

2. Choose a well-ventilated location away from heat sources and direct sunlight. The location must be dry to prevent rust and leakage.

3. During placement, ensure at least 5 cm of clearance on the top, 10 cm on both sides, and 5 cm at the back for heat dissipation.

4. Use the front adjusting legs to level the appliance, which is necessary for the door to close properly and avoid malfunctions.

5. Before first use, clean the interior with lukewarm water and neutral soap, then dry thoroughly.

6. After installation or door reversal, wait at least 4 hours before plugging the appliance in to allow compressor oil to settle.

7. Check that the voltage and frequency on the type plate match your power supply. Plug in, and after one hour, check that the interior temperature is lower, indicating normal operation.

To reverse the door on your WISBERG WBVR170NFE, use a crosshead screwdriver, flat head screwdriver, and an adjustable spanner. Perform this with two people and ensure the appliance is not laid flat, as this can damage the cooling system.

1. Unplug and empty the appliance.

2. Remove the cover of the top right hinge. Unscrew the hinge and dismantle it.

3. Remove the cover for the left hinge point.

4. Dismantle the door cover and mount it on the opposite side. Carefully lift the door off the bottom hinge and place on a soft surface.

5. Remove both bottom adjusting legs and the hinge bracket on the bottom right. Unscrew the hinge pin, turn the bracket over, and screw the pin back on.

6. Install the bracket on the bottom left and replace the adjusting legs.

7. Remount the door, ensuring it is level horizontally and vertically.

8. Put the top hinge bracket back in place and screw it to the top of the appliance.

9. Place the covers over the hinge points.

10. Remove the door gaskets, rotate them, and reattach. Check alignment and adjust legs if necessary.

You can set the temperature of the WISBERG WBVR170NFE by pressing the Set button. The setting is confirmed if the button is not pressed again within 5 seconds.

Available settings are: -14, -16, -18, -20, -22 degrees Celsius and Super Freeze. The recommended setting is -18 degrees Celsius.

Super Freeze mode on the WISBERG WBVR170NFE quickly cools the compartment to prevent the loss of nutritional value and keep food fresh. To activate it, hold the Set button for 3 seconds until the Super symbol lights up. To deactivate, hold the Set button for another 3 seconds. Note that the appliance will consume more energy than usual in this mode.

The WISBERG WBVR170NFE has two primary alarms:

Door Alarm: Sounds if the door is left open for more than 90 seconds. Close the door or press the Set button to turn it off.

Temperature Alarm: Triggers if the temperature exceeds -6 degrees Celsius for more than 6 hours. The 5 indicator lights on the display will flash. It turns off automatically once the temperature drops below -10 degrees Celsius, or you can stop it by pressing the Set button.

The WISBERG WBVR170NFE is designed to operate optimally within specific ambient temperature ranges based on its climate class (SN, N, ST, T):

SN: +10 to +32 degrees Celsius

N: +16 to +32 degrees Celsius

ST: +16 to +38 degrees Celsius

T: +16 to +43 degrees Celsius

For best results with your WISBERG WBVR170NFE, follow these food storage tips:

1. The appliance can freeze up to 13 kg of food in 24 hours.

2. Cool hot food to room temperature before placing it in the freezer.

3. Prepare food in small portions for faster freezing and easier thawing.

4. Keep fresh, unfrozen food away from already frozen items.

5. Pack food airtight in bags to prevent freezer burn and odor transfer.

6. Leave space between items to ensure cold air can circulate properly.

Always unplug the WISBERG WBVR170NFE before cleaning. Do not use mechanical devices or heaters to defrost, as this is a no-frost freezer. Clean the interior regularly with a soft cloth or sponge using lukewarm water and neutral detergent. Dust the back and side panels periodically with a dry cloth. If the appliance will be out of use for several months, unplug it, clean it, and leave the door open to prevent mold.

If the WISBERG WBVR170NFE is not cooling, check the following:

1. Ensure the thermostat is set to the correct position.

2. Verify the plug is securely in the socket.

3. Check if the socket has power by verifying if the interior light comes on when the door is opened.

4. Ensure the ambient temperature is at least 10 degrees Celsius; if it is lower, the cooling system may not function correctly.

5. Check for a blown fuse.

It is normal for the side panels of the WISBERG WBVR170NFE to feel hot. This is due to the heat exchanger components located on the sides of the appliance. They are hottest right after installation and will cool down once the appliance reaches its internal target temperature.

The physical dimensions of the WISBERG WBVR170NFE are 55 cm (W) x 59.4 cm (D) x 168.3 cm (H).

To ensure proper operation and heat dissipation, observe the following minimum clearance requirements:

Top: 5 cm

Sides: 10 cm

Back: 5 cm