Free English WHIRLPOOL UXT4030AY (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD WHIRLPOOL UXT4030AY (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
What should I do before servicing or cleaning the WHIRLPOOL UXT4030AY range hood?
Before servicing or cleaning the unit, switch power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
What is required for proper combustion and exhausting of gases when installing the WHIRLPOOL UXT4030AY range hood?
Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel burning equipment to prevent backdrafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
What type of ductwork should be used for the WHIRLPOOL UXT4030AY range hood to reduce the risk of fire?
To reduce the risk of fire, use only metal ductwork for the WHIRLPOOL UXT4030AY range hood.
What precautions should be taken to reduce the risk of a range top grease fire when using the WHIRLPOOL UXT4030AY range hood?
Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly on low or medium settings.
Always turn hood ON when cooking at high heat or when flambeing food (i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambé).
Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or filter.
Use proper pan size. Always use cookware appropriate for the size of the surface element.
What should I do to reduce the risk of injury to persons in the event of a range top grease fire when using the WHIRLPOOL UXT4030AY range hood?
Smother flames with a close fitting lid, cookie sheet, or metal tray, then turn off the burner. Be careful to prevent burns. If the flames do not go out immediately, evacuate and call the fire department.
Never pick up a flaming pan – you may be burned.
Do not use water, including wet dishcloths or towels – a violent steam explosion will result.
Use an extinguisher ONLY if:
You know you have a class ABC extinguisher, and you already know how to operate it.
The fire is small and contained in the area where it started.
The fire department is being called.
You can fight the fire with your back to an exit.
What warning should be observed regarding speed control devices for the WHIRLPOOL UXT4030AY range hood?
To reduce the risk of fire or electrical shock, do not use this fan with any solid-state speed control device on the WHIRLPOOL UXT4030AY range hood.
What tools are needed for the installation of the WHIRLPOOL UXT4030AY range hood?
Tools needed for the WHIRLPOOL UXT4030AY range hood installation include:
- Drill
- 11/4″ (3.0 cm) drill bit
- 1/8″ (3.0 mm) drill bit for pilot holes
- Pencil
- Wire stripper or utility knife
- Tape measure or ruler
- Caulking gun and weatherproof caulking compound
- Flat-blade screwdriver
- Phillips screwdriver
- Saber or keyhole saw
What parts are supplied with the WHIRLPOOL UXT4030AY range hood?
Parts supplied with the WHIRLPOOL UXT4030AY range hood are:
- T-10 Torx®+ adapter
- 4 – 4.5 x 13 mm mounting screws
What parts are needed for the installation of the WHIRLPOOL UXT4030AY range hood?
Parts needed for the WHIRLPOOL UXT4030AY range hood installation include:
- 3 – UL listed wire connectors
- 1 – 75W max, 120V incandescent light bulb
For cabinets with recessed bottoms, you will also need:
- Two 2″ (5.1 cm) wide filler strips. Length and thickness determined by recess dimensions.
- Four flat head wood screws or machine screws with washers and nuts (to attach filler strips).
What are the location requirements for installing the WHIRLPOOL UXT4030AY range hood?
For the WHIRLPOOL UXT4030AY range hood installation:
- Observe all governing codes and ordinances.
- It is the installer’s responsibility to comply with installation clearances specified on the model/serial rating plate. The model/serial rating plate is located inside the range hood on the left wall.
- Range hood location should be away from strong draft areas, such as windows, doors and strong heating vents.
- Cabinet opening dimensions that are shown must be used. Given dimensions provide minimum clearance. Consult the cooktop/range manufacturer installation instructions before making any cutouts.
- Grounded electrical outlet is required. See “Electrical Requirements” section.
- All openings in ceiling and wall where range hood will be installed must be sealed.
What are the installation clearances for the WHIRLPOOL UXT4030AY range hood?
The installation clearances for the WHIRLPOOL UXT4030AY range hood are:
| Label | Description |
|---|---|
| A. | 18″ (45.7 cm) min. clearance – upper cabinet to countertop |
| B. | 18″ (45.7 cm) to 24″ (61.0 cm) suggested max. – bottom of range hood to cooking surface |
| C. | 30″ (76.2 cm) min. cabinet opening width for 30″ (76.2 cm) models and 36″ (91.4 cm) min. cabinet width for 36″ (91.4 cm) models |
| D. | 13″ (33.0 cm) cabinet depth |
| E. | 36″ (91.4 cm) base cabinet height |
What electrical requirements must be met for installing the WHIRLPOOL UXT4030AY range hood?
The electrical requirements for the WHIRLPOOL UXT4030AY range hood are:
- Observe all governing codes and ordinances.
- Ensure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.
- If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.
- A 120 volt, 60 Hz., AC only, 15-amp, fused electrical circuit is required.
- If the house has aluminum wiring, follow the procedure below:
- Connect a section of solid copper wire to the pigtail leads.
- Connect the aluminum wiring to the added section of copper wire using special connectors and/or tools designed and UL listed for joining copper to aluminum. Follow the electrical connector manufacturer’s recommended procedure. Aluminum/copper connection must conform with local codes and industry accepted wiring practices.
- Wire sizes and connections must conform with the rating of the appliance as specified on the model/serial rating plate. The model/serial plate is located behind the filter on the rear wall of the range hood.
- Wire sizes must conform to the requirements of the National Electrical Code, ANSI/NFPA 70 (latest edition), or CSA Standards C22. 1-94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 (latest edition) and all local codes and ordinances.
How do I prepare the location for installing the WHIRLPOOL UXT4030AY range hood?
To prepare the location for the WHIRLPOOL UXT4030AY range hood:
NOTE: Before making cutouts, make sure there is proper clearance within the ceiling or wall.
1. Disconnect power.
2. Select a flat surface for assembling the range hood. Place covering over that surface.
3. Lift the range hood and set it upside down onto covered surface.
4. If cabinet has recessed bottom, add wood filler strips on each side. Install screws to attach filler strips in locations shown.
How do I determine the wiring hole location for the WHIRLPOOL UXT4030AY range hood?
To determine the wiring hole location for the WHIRLPOOL UXT4030AY range hood:
Cut only one 11/4″ (3.2 cm) diameter wiring access hole.
1. Determine and clearly mark a vertical centerline on the wall and cabinet in the area the vent opening will be made.
To wire through top:
1. Mark a line distance “A” from the right of the centerline on the underside of the cabinet. Mark the point on this line that is 7/8″ (2.2 cm) from back wall. Drill a 11/4″ (3.2 cm) diameter hole through the cabinet at this point.
To wire through wall:
1. Mark a line distance “A” from the right of the centerline on the underside of the wall. Mark the point on this line that is 7/8″ (2.2 cm) from the underside of the cabinet. Drill a 11/4″ (3.2 cm) diameter hole through the rear wall at this point.
What is the procedure to install the range hood for the WHIRLPOOL UXT4030AY?
To install the range hood for the WHIRLPOOL UXT4030AY:
1. Lift the range hood up under cabinet and determine final location by centering beneath cabinet. Mark on the underside of cabinet the location of the 4 keyhole mounting slots on the range hood. Set range hood aside on a covered surface.
2. Use 1/8″ (3 mm) drill bit and drill 4 pilot holes as shown.
3. Install the 4 – 4.5 mm x 13 mm mounting screws in pilot holes. Leave about 1/4″ (6.4 mm) space between screw heads and cabinet to slide range hood into place.
Non-vent (recirculating) installations – Do not remove any knockouts.
4. Using 2 or more people, lift the hood into final position. Feed enough electrical wire through the 1/2″ UL listed or CSA approved strain relief to make connections in the terminal box. Tighten the strain relief screws.
5. Position the range hood so that the large end of the keyhole slots are over the mounting screws. Then push the hood toward the wall so that the screws are in the neck of the slots. Tighten the mounting screws, making sure the screws are in the narrow neck of slots.
What is the Power Supply Cable Installation procedure for the WHIRLPOOL UXT4030AY range hood?
For Power Supply Cable Installation on the WHIRLPOOL UXT4030AY range hood:
1. For direct wire installations, run the home power supply cable according to the National Electric Code or CSA standards and local codes and ordinances. There must be enough wiring from the fused disconnect (or circuit breaker) box to make the connection in the hood electrical terminal box. For optional power supply cord kit installations, follow the instructions in the “Make Electrical Connections” section. NOTE: Do not reconnect power until the installation is complete.
2. Remove the screw from the terminal box cover. Remove terminal box cover and set aside.
3. Remove the power supply knockout from the top or rear of the vent hood (depending on the incoming location of your home power supply cable) and install a UL listed or CSA approved 1/2″ strain relief.
How do I make the electrical connection for the WHIRLPOOL UXT4030AY range hood?
To make the electrical connection for the WHIRLPOOL UXT4030AY range hood:
1. Disconnect power.
2. Use UL listed wire connectors and connect white wires (A) together.
3. Use UL listed wire connectors and connect black wires (B) together.
4. Connect green (or bare) ground wire from power supply to green ground screw in terminal box and securely tighten.
5. Install terminal box cover.
6. Reconnect power.
How do I complete the installation of the WHIRLPOOL UXT4030AY range hood?
To complete the installation of the WHIRLPOOL UXT4030AY range hood:
1. Install the 75W (max.) Incandescent light bulb. See “Replacing the Incandescent Light Bulb” in the “Range Hood Care” section.
2. Replace grease filter if removed. See the “Range Hood Care” section.
3. Check the operation of the range hood fan and light. See “Range Hood Use” section. If range hood does not operate, check to see whether a circuit breaker has tripped or a household fuse has blown. Disconnect power and check wiring connections.
How should I operate the light on the WHIRLPOOL UXT4030AY range hood?
To operate the light on the WHIRLPOOL UXT4030AY range hood, push the light switch (A) to the left to turn the light On. Push the light switch to the right to turn the light Off.
How should I operate the fan on the WHIRLPOOL UXT4030AY range hood?
To operate the fan on the WHIRLPOOL UXT4030AY range hood:
Push the fan switch (B) to the left for Low speed. Push the fan switch to the right for High speed. Push the fan switch to the middle for Off.
How should I clean the exterior surfaces of the WHIRLPOOL UXT4030AY range hood?
To clean the exterior surfaces of the WHIRLPOOL UXT4030AY range hood:
IMPORTANT: Do not use soap-filled scouring pads, abrasive cleaners, Cooktop Polishing Creme, steel wool, gritty washcloths or paper towels.
To avoid damage to the stainless steel, do not use cleaners that contain chlorine.
Cleaning Method:
- Rub in direction of grain to avoid scratching or damaging the surface.
- For stainless steel models, use Stainless Steel Cleaner and Polish Part Number 31462A (not included): See “Assistance or Service” section to order.
- Liquid detergent or all-purpose cleaner: Rinse with clean water and dry with soft, lint-free cloth.
- Glass cleaner to remove fingerprints.
How do I replace the charcoal filter in the WHIRLPOOL UXT4030AY range hood?
To replace the charcoal filter in the WHIRLPOOL UXT4030AY range hood:
1. Remove screw from the filter retainer.
2. Turn the filter retainer to release filter.
3. Reinstall the filter by placing the back edge in the channel at rear of hood. Push filter into place, turn the filter retainer to secure filter to range hood.
4. Replace screw in the filter retainer.
How do I replace the incandescent light bulb in the WHIRLPOOL UXT4030AY range hood?
To replace the incandescent light bulb in the WHIRLPOOL UXT4030AY range hood:
Turn off the range hood and allow the light bulb to cool.
1. Disconnect power.
2. Squeeze the plastic lens cover and remove it from the hood.
3. Screw light bulb into socket.
4. Replace lens cover by squeezing cover and inserting tabs into slots.
5. Reconnect power.
If new light does not operate, make sure the lamp is inserted correctly before calling service.
How do I finish the installation of the WHIRLPOOL UXT4030AY range hood in French instructions?
To finish the installation of the WHIRLPOOL UXT4030AY range hood:
1. Installer l’ampoule à incandescence de 75 watts (maximum). Voir “Remplacement de l’ampoule à incandescence” à la section “Entretien de la hotte”.
2. Réinstaller le filtre à graisse s’il a été retiré. Voir la section “Entretien de la hotte”.
3. Contrôler le fonctionnement du ventilateur de la hotte et de la lampe. Voir la section “Utilisation de la hotte”. Si la hotte ne fonctionne pas, déterminer si un disjoncteur s’est ouvert ou si un fusible du domicile est grillé. Déconnecter la source de courant électrique et inspecter les connexions du câblage.
REMARQUE: Pour pouvoir tirer le plus grand parti de la nouvelle hotte de cuisinière, lire la section “Utilisation de la hotte”.