WESTERMO SDW-550B (01) PDF Document

Before installation, read the manual completely and gather all information on the unit. Make sure you understand it fully and check that your application does not exceed the safe operating specifications for the WESTERMO SDW-550B.

The WESTERMO SDW-550B should only be installed by qualified personnel.

The WESTERMO SDW-550B should be built-in to an apparatus cabinet, or similar, where access is restricted to service personnel only.

The power supply wiring must be sufficiently fused, and if necessary it must be possible to disconnect manually from the power supply. Ensure compliance to national installation regulations.

The WESTERMO SDW-550B uses convection cooling. To avoid obstructing the air flow around the unit, follow the spacing recommendations.

Prevent access to hazardous voltage by disconnecting the unit from power supply.

Warning! Do not open connected WESTERMO SDW-550B unit. Hazardous voltage may occur within this unit when connected to power supply.

Do not look directly into the fibre optical port or any connected fibre although this unit is designed to meet the Class 1 Laser regulations.

Follow the care recommendations below to maintain full operation of the WESTERMO SDW-550B and to fulfil the warranty obligations.

This unit must not be operating with removed covers or lids.

Do not attempt to disassemble the unit. There are no user serviceable parts inside.

Do not drop, knock or shake the unit, rough handling above the specification may cause damage to internal circuit boards.

Do not use harsh chemicals, cleaning solvents or strong detergents to clean the unit.

Do not paint the unit. Paint can clog the unit and prevent proper operation.

Do not expose the unit to any kind of liquids (rain, beverages, etc). The unit is not waterproof. Keep the unit within the specified humidity levels.

Do not use or store the unit in dusty, dirty areas, connectors as well as other mechanical part may be damaged.

If the unit is not working properly, contact the place of purchase, nearest Westermo distributor office or Westermo Tech support.

Fibre connectors are supplied with plugs to avoid contamination inside the optical port. As long as no optical fibre is mounted on the connector, e.g. for storage, service or transportation, should the plug be applied.

Fibre optic equipment needs special treatment. It is very sensitive to dust and dirt.

If the fibre will be disconnected from the modem the protective hood on the transmitter/receiver must be connected.

The protective hood must be kept on during transportation.

The fibre optic cable must also be handle the same way.

If this recommendation is not followed it can jeopardise the warranty.

In the event of contamination, the optical connectors should be cleaned by the use of forced nitrogen and some kind of cleaning stick.

Recommended cleaning fluids for the WESTERMO SDW-550B are:

• Methyl-, ethyl-, isopropyl- or isobutyl-alcohol
• Hexane
• Naphtha

No maintenance is required, as long as the unit is used as intended within the specified conditions for the WESTERMO SDW-550B.

This symbol means that the product shall not be treated as unsorted municipal waste when disposing of it. It needs to be handed over to an applicable collection point for recycling electrical and electronic equipment.

By ensuring this product is disposed of correctly, you will help to reduce hazardous substances and prevent potential negative consequences to both environment and human health, which could be caused by inappropriate disposal.

The WESTERMO SDW-550B is auto configured (auto-negotiation) or manually setting of speed and duplex of individual TX port, by DIP-switches.

The port mirror function is possible to set with DIP-switch on the WESTERMO SDW-550B. With the port mirror function active the switch will copy all outgoing traffic to port 1. This can be used to monitor all traffic going out from the switch. Packets may be discarded if the total throughput exceeds the port speed of port 1.

Features of the WESTERMO SDW-550B include:

• TX shields individually isolated
• Wide DC power range 12 – 48 VDC
• Wide temperature range
• Automatic MDI/MDI-X crossover
• LED indicators for Power, Speed, Duplex, Link and Traffic
• Port monitoring
• 35 mm DIN rail mounting
• Enable or disable of flow control

Examples of applications for the WESTERMO SDW-550B are:

• 5-port switch
• Ethernet isolator, for STP networks

The power interface to all other interfaces on the WESTERMO SDW-550B has an isolation rating of 2.8 kV DC 2.0 kV RMS @ 50 Hz and 60 s duration.

The TX signal Interface to all other interfaces on the WESTERMO SDW-550B has an isolation rating of 2.1 kV DC 1.5 kV RMS @ 50 Hz and 60 s duration.

The TX shield Interface to all other interfaces on the WESTERMO SDW-550B has an isolation rating of 1.5 kV DC 1.0 kV RMS @ 50 Hz and 60 s duration.

The operating temperature for the WESTERMO SDW-550B is -25 to +70°C.

The temperature range for storage and transportation of the WESTERMO SDW-550B is -25 to +70°C.

The relative humidity operating condition for the WESTERMO SDW-550B is 5 to 95% (non-condensing).

The relative humidity conditions for storage and transportation of the WESTERMO SDW-550B is 5 to 95% (condensation allowed outside packaging).

The maximum altitude for operating the WESTERMO SDW-550B is 2000 m/70 kPa.

The mechanical specifications for the WESTERMO SDW-550B are:

The mounting for the WESTERMO SDW-550B is DIN-rail.

The degree of protection for the WESTERMO SDW-550B is IP21.

DIP-switches are used to configure the speed and duplex of individual TX ports on the WESTERMO SDW-550B. Configurations include:

• Auto-negotiation and auto MDI/MDI-X disabled
• Auto-negotiation and auto MDI/MDI-X enabled
• 10 Mbit/s speed selected
• 100 Mbit/s speed selected
• Half duplex selected
• Full duplex selected

To be observed when the DIP-switches will be configured on the WESTERMO SDW-550B:

• Speed and duplex setting only valid when auto-negotiation is disabled.
• When monitoring selected all outgoing packets from the switch is also copied to the port 1.
• Speed and duplex switch settings are ignored for FX ports.
• If auto-negotiation and auto MDI/MDI-X disabled all TX ports support MDI-X configuration.

The WESTERMO SDW-550B (Model SDW-550B) has 5 ports of 10/100Base-T/TX.

The fibre optic power budget specifications for models with multimode (MM-xx2) fibre type are:

The fibre optic power budget specifications for WESTERMO SDW-550B models using Singlemode SM-SC15 fibre type are:

The fibre optic power budget specifications for WESTERMO SDW-550B models using Singlemode SM-LC15 fibre type are:

The fibre optic power budget specifications for WESTERMO SDW-550B models using Singlemode SM-LC40 fibre type are:

The normal attenuation in connectors or splices for the WESTERMO SDW-550B is:

The power specifications for the WESTERMO SDW-500 series, which includes the WESTERMO SDW-550B, are:

The rated current for the WESTERMO SDW-550B (Model SDW-550) at 12VDC power input is 320 mA.

The rated frequency is DC.

Connection is via Detachable screw terminal, with connector size 0.2 – 2.5 mm² (AWG 24-12).

The electrical specifications for Ethernet TX on the WESTERMO SDW-550B are based on IEEE std 802.3. 2000 edition:

The electrical specifications for Ethernet FX on the WESTERMO SDW-550B are based on IEEE std 802.3. 2000 edition:

The PWR LED indicates the internal power status. When ON, the internal power is OK. When Slow flash, initialisation is progressing. When Fast flash, there is an initialisation error.

The LINK LED indicates the Link status of every port. When OFF, there is No Ethernet link. When ON, there is a Good Ethernet link. When Flash, Ethernet data is transmitted or received (traffic indication).

The SPD LED (TX only) indicates the speed: OFF for 10 Mbit/s and ON for 100 Mbit/s.

The DPX LED (TX only) indicates the duplex setting: OFF for Half duplex and ON for Full duplex.

The WESTERMO SDW-550B unit should be mounted on a 35 mm DIN-rail which is horizontally mounted on a wall or cabinet backplate.

To avoid obstructing the airflow around the unit due to convection cooling, use the following spacing rules: Recommended spacing 25 mm (1.0 inch) above/below and 10 mm (0.4 inches) left/right the unit.

Snap on mounting is performed as shown in the figure.

To remove the WESTERMO SDW-550B unit, press down the black support at the back of the unit.

DIP switch S1 settings for Port 1 on the WESTERMO SDW-550B determine the configuration:

Note: Speed and duplex settings are ignored for FX ports.

DIP switch S1 settings for Port 2 on the WESTERMO SDW-550B determine the configuration:

Note: Speed and duplex settings are ignored for FX ports.

DIP switch S1 settings for Port 3 on the WESTERMO SDW-550B determine the configuration:

Note: Speed and duplex settings are ignored for FX ports.

Port mirroring settings are controlled by DIP switch S2 on the WESTERMO SDW-550B:

Flow control settings are controlled by DIP switch S3 on the WESTERMO SDW-550B:

The factory settings for the DIP switches on the WESTERMO SDW-550B are:

• S1: All switches OFF
• S2: All switches OFF
• S3: All switches OFF