VOLTCRAFT 2301363 (01) PDF MANUAL

This product serves as a camera attachment for endoscopes BS-500 and BS-1000 (both not included in delivery) for visual fault tracing or inspection with dead-voltage systems and equipment. The flexible camera neck allows the camera at the top to be positioned so it can reach into otherwise inaccessible locations. The four LEDs built into the camera head enable shooting in total darkness, with brightness controlled via the connected endoscope. The waterproof camera neck and camera head are ideally suited for dead-voltage fluids (no acids or alkaline solutions). Use on humans or animals, or in explosive areas, is not permitted. Power is supplied via the connected endoscope.

This product is intended for indoor use only. Do not use it outdoors.

• Endoscope camera

• Protective cap

• Operating instructions

The symbol with the lightning in the triangle is used if there is a risk to your health, e.g. due to an electric shock.

The symbol with the exclamation mark in the triangle is used to indicate important information in these operating instructions. Always read this information carefully.

The arrow symbol indicates special information and advice on operation.

Read the operating instructions carefully and especially observe the safety information. If you do not follow the safety instructions and information on proper handling in this manual, we assume no liability for any resulting personal injury or damage to property. Such cases will invalidate the warranty/guarantee.

• The device is not a toy. Keep it out of the reach of children and pets.

• Do not leave packaging material lying around carelessly. This may become dangerous playing material for children.

• Protect the appliance from extreme temperatures, direct sunlight, strong jolts, flammable gases, steam and solvents.

• Do not place the product under any mechanical stress.

• If it is no longer possible to operate the product safely, take it out of operation and protect it from any accidental use. Safe operation can no longer be guaranteed if the product:

– is visibly damaged,

– is no longer working properly,

– has been stored for extended periods in poor ambient conditions or

– has been subjected to any serious transport-related stresses.

• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage the product.

• On industrial sites, the accident prevention regulations of the association of the industrial workers’ society for electrical equipment and utilities must be followed.

• Never switch the device on immediately after it has been taken from a cold into a warm environment. Condensation that forms might destroy your device. Allow the device to reach room temperature before switching it on.

• Consult an expert when in doubt about the operation, safety or connection of the appliance.

• Maintenance, modifications and repairs must only be completed by a technician or an authorised repair centre.

• If you have questions which remain unanswered by these operating instructions, contact our technical support service or other technical personnel.

Also observe the safety and operating instructions of any other devices which are connected to the product.

Only immerse the camera head and camera neck in liquids that are voltage free! The camera neck is not to be submerged further than the marking “MAX Water Level”.

The endoscope may only be used for inspection of dead systems. The camera head is made of metal and can lead to short circuits. For safety reasons, disconnect all system parts from the power supply before every inspection.

Avoid strong mechanical strains or vibrations. Make sure you never go below the minimum bending radius of 50 mm.

Put the protective cap back onto the camera lens when the camera is no longer in use.

• Plug the connecting plug on the top of the endoscope carefully into the connecting socket of the camera neck.

• Make sure that the connecting socket is oriented exactly towards the pins of the connecting plug. There is an arrow printed on the connecting socket. This arrow must point towards the display of the endoscope.

• Turn the mounting ring clockwise to fasten the connection.

• You will find notes on controlling the brightness of the LEDs in the operating instructions of the manual.

• Follow these steps in reverse order when disconnecting the camera from the endoscope.

• Disconnect the product from the mains before each cleaning.

• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can cause damage to the housing and malfunctioning.

• To clean the camera lens, use a small brush or cotton swab.

• To clean the camera neck, use a cloth lightly dampened with lukewarm water.

Electronic devices are recyclable waste and must not be disposed of in the household waste. At the end of its service life, dispose of the product in accordance with applicable regulatory guidelines.

You thus fulfill your statutory obligations and contribute to the protection of the environment.

Image sensor	CMOS
Camera lighting	4 white LEDs
Exposure	automatic
White balance	fixed
Operating/Storage conditions	-20 to +60 °C, max. 95 %
Bend radius	min. 50 mm
Protection class	IP67
Field of view	90°
Depth of field	10 – 50 mm
Dimensions (ø x L)	Item No. 2301360: 3.9 mm x 1 m Item No. 2301361: 3.9 mm x 2 m Item No. 2301362: 3.9 mm x 3 m Item No. 2301363: 3.9 mm x 5 m Item No. 2301364: 3.9 mm x 10 m