VINCI EXPRESS 2 (01) PDF DOCUMENT

When using electrical appliances, basic safety precautions should be followed, including:

• Remove all bags and packaging from appliance before use.

• Never leave appliance unattended when in use.

• Make sure the appliance is cleaned thoroughly before using.

• Do not use appliance for other than intended use. For household use only. Do not use outdoors.

• Close supervision is necessary when any appliance is used by or near children.

• Do not operate this appliance with a damaged cord, damaged plug, after the appliance malfunctions, is dropped, or damaged in any manner.

• Never use abrasive cleaning agents to clean your VINCI EXPRESS 2 Cold Brew Maker.

• To prevent the risk of fire, electric shock, or personal injury, do not put cord, plug, or appliance in or near water or other liquids.

• Do not place appliance on or near a hot gas burner, hot electric burner, or in a heated oven.

• Refrain from using attachments that are not recommended by the appliance manufacturer, as this may result in fire, electric shock, or personal injury.

• Do not let the cord touch hot surfaces or hang over the edge of tables or counters.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge unless they are provided with supervision and instruction concerning use of the appliance by a person responsible for their safety.

• Always be sure to unplug the appliance from outlet prior to moving, cleaning, storage, and when not in use.

• Vinci Housewares shall not accept liability for damages caused by improper use of the appliance.

• Before first use, and after subsequent uses wash all parts with warm soapy water, EXCEPT for the Control Lid which should never be submerged in water.

• Read and remove all warning labels, stickers, and packaging materials.

• Carefully read all the instructions.

NEVER Use Fine Grind or Instant Coffee. Fine grind or Instant coffee will clog the filter, damage the pump, and void warranty.

NEVER Use Hot Water. Using hot water will void warranty. Only use ROOM TEMPERATURE water.

A. Control Lid

B. Water Pickup Tube

C. Filter Basket Assembly

C1. Top Filter Cap

C2. O-Ring Seal

C3. Main Filter Basket

C4. Filter Basket Bottom Cap

D. Control Lid Assembly

E. Durable Plastic Carafe

F. 2-Tablespoon Scoop

G. Serving Lid

H. Cleaning Cup

I. Power Adapter

J. Instruction Manual

1. Power On/Off: To turn on your VINCI EXPRESS 2, press the power button. It glows blue in standby mode and turns red when powered on.

2. Vinci Brew Button: After selecting your desired Brew Strength function, start the process by pressing the Brew button. The button’s illumination indicates:

• White: The VINCI EXPRESS 2 is in standby mode.

• Blue: The brewing process is underway.

• Not illuminated: The device is off or there’s no power.

BREW STRENGTHS:

3. Light – 10-Minute Brew Cycle: For a light ready-to-drink brew.

4. Medium – 15 Minute Brew Cycle: For a stronger brew, great over ice.

5. Bold – 25 Minute Brew Cycle: For a robust brew that can be diluted while maintaining flavor.

6. Clean: Use the ‘Clean’ setting after each brew. This practice maintains both the freshness of your coffee and the performance of your device.

IMPORTANT: Make sure that all surfaces are clean of any unwanted minerals or coffee grounds before using. This will ensure that the brewer will provide the best cup of cold-brewed coffee.

1. GETTING STARTED: Lift the Control Lid Assembly from the Carafe and remove the Cleaning Cup.

2. FILL CARAFE WITH WATER: Fill the Carafe with fresh, clean ROOM TEMPERATURE water to the Fill Line. Filtered water is best (or recommended). Never fill past the Fill Line.

3. REMOVE FILTER BASKET: Remove the Filter Basket from the Control Lid by rotating it counter-clockwise.

4. REMOVE TOP CAP: Remove the Top Filter Cap by placing your fingers at the noted notches and lift it away from the Filter Basket.

5. FILL COFFEE/RE-INSERT TOP CAP: Fill the Filter Basket with approximately 9 Scoops of Medium to Coarse grind coffee, leaving about 1/2″ of unfilled space. Then re-insert the Top Filter Cap. IMPORTANT: Do not pack or tamp coffee in the filter.

6. RE-INSERT FILTER BASKET/PLACE LID ASSEMBLY: Re-attach the Filter Basket Assembly to the Control Lid by turning it clockwise. Slowly place the Control Lid Assembly into the Carafe, ensuring the Filter Basket is fully submerged in the water.

7. POWER ON: Plug the Power Adapter into an electrical outlet first, then into the Control Lid. After plugging in the Power Adapter, press the power button.

8. BREW SELECT: Select your desired brew strength. Press the Brew button to start the brew cycle. The Brew button will illuminate blue while running.

BREWING PROCESS COMPLETE: Once the cycle is complete, the Brew button will illuminate white and you’ll hear three short beeps, signaling that your brew is ready.

PURGE: Upon completion of the brew cycle, partially lift the Control Lid Assembly and press the Brew button. The pump will run and purge the remaining cold brew from the Filter Basket. After about 20 seconds, press the Brew button again to stop the pump.

CONTROL LID TO CUP: Place the Control Lid Assembly into the Cleaning Cup. For detailed cleaning instructions, refer to the ‘Care and Cleaning’ section.

SERVING: Place the Serving Lid on the Carafe. You are now ready to serve your cold brew. To store, rotate the serving lid to the closed position. It can be stored in the refrigerator for up to 10 days.

IMPORTANT: After every use, wash all parts to ensure that the unit will be working like new. Never submerge the Control Lid in water. Doing so will damage the unit and void the warranty.

1. REMOVE LID FROM CUP: Remove the Control Lid Assembly from the Cleaning Cup.

2. REMOVE FILTER BASKET: Remove the Filter Basket Assembly from the Control Lid by rotating it counter-clockwise and then remove the Top Filter Cap from the Filter Basket.

3. DISCARD COFFEE: Over a trash or compost bin, invert the Filter Basket, remove the Bottom Filter Cap, and dispose of the used coffee. After disposing of used grounds, rinse all parts.

4. FILL CUP WITH WATER: Fill the Cleaning Cup about 1/2 full with clean fresh water, up to the MAX FILL line.

5. RINSE WATER TUBE FILTER: Inspect the bottom of the Water Pickup Tube for any coffee grounds. If found, carefully rinse only the bottom of the tube, ensuring no water reaches the Control Lid.

6. CLEAN: Place the Control Lid into the Cleaning Cup and Press the Clean button to start the cleaning process.

7. PURGE AND DISCARD WATER: Once the cleaning cycle finishes, lift the Control Lid until the Water Pickup Tube is clear of the water in the Cleaning Cup. Press the Clean button again to flush any remaining water through the pump system. Empty the dirty water and rinse the Cleaning Cup.