VERACITY HIGHWIRE LONGSTAR VLS-1P-CC (01) Image

Free English VERACITY HIGHWIRE LONGSTAR VLS-1P-CC (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.


CLICK HERE TO DOWNLOAD VERACITY HIGHWIRE LONGSTAR VLS-1P-CC (01) PDF DOCUMENT

If this is not the document you want for this product, click here to see if we have any other documents for this product.

What do the LEDs on the BNC coaxial connector side of the VERACITY HIGHWIRE LONGSTAR VLS-1P-CC indicate?

The status of the Green and Yellow LEDs on the BNC connector side indicates the power and coax link status of the VERACITY HIGHWIRE LONGSTAR VLS-1P-CC.

LED FUNCTION
Green
Blink = Power good, no link detected
Rapid blink = Establishing coax link
Flash = 10Base-T link established
On = 100Base-TX link established
Yellow
On = Coax link established
Blink off = Network activity on coax link

What do the LEDs on the RJ45 Ethernet connector side of the VERACITY HIGHWIRE LONGSTAR VLS-1P-CC indicate?

The status of the RJ45 Green and Yellow LEDs indicates the power and Ethernet link status of the VERACITY HIGHWIRE LONGSTAR VLS-1P-CC.

LED FUNCTION
RJ45 Green
On = Power good
RJ45 Yellow
On = 10Base-T or 100Base-TX link established
Blink off = Network activity on Ethernet link

What are the powering options for the VERACITY HIGHWIRE LONGSTAR VLS-1P-CC?

The VERACITY HIGHWIRE LONGSTAR VLS-1P-CC can be powered in the following ways:

1. For most installations, a POE input from a POE switch or injector will deliver enough power for both the HIGHWIRE Longstar devices and the camera.

2. If additional power and range is required, or as an alternative to a POE source, a 57V DC power supply may be connected at the BASE side.

3. In some cases where cable length and/or quality does not support the required power, a 57V power supply may be connected at the CAMERA side, which provides a full POE output.


What is the POE over coax range of the VERACITY HIGHWIRE LONGSTAR VLS-1P-CC based on power source and cable type?

The following table outlines the typical limits for 100Base-TX connections with the VERACITY HIGHWIRE LONGSTAR VLS-1P-CC. For non-POE installations (Ethernet only), use the “0” Zero figures.

POWER SOURCE POE Plus Switch Veracity Power Supply
Camera Power watts Camera Power watts
0 5 10 15 20 25 0 5 10 15 20 25
RG59 (22AWG CCS) 540m 200m 130m 100m 60m N/A 540m 400m 240m 140m 100m 60m
RG59 (20AWG core) 690m 690m 600m 500m 350m N/A 690m 690m 690m 690m 640m 360m
RG6 (18AWG core) 950m 950m 800m 700m 470m N/A 950m 950m 950m 950m 900m 500m
RG11 (14AWG core) 1400m 1400m 1400m 1400m 1200m N/A 1400m 1400m 1400m 1400m 1400m 1300m

Note: The data range at 10Base-T is approximately 3 times further.


What should I know about surge protection for my VERACITY HIGHWIRE LONGSTAR VLS-1P-CC?

All Veracity products have been independently tested to verify their resilience to the stringent immunity levels of international standards. Users should note that no electronic equipment can be guaranteed to be completely protected at levels beyond the defined standard.

It is the user’s responsibility to implement relevant surge protection measures, as appropriate to the installation. This may include the fitting of additional surge protection devices where required.


How do I prepare the VERACITY HIGHWIRE LONGSTAR VLS-1P-CC for use in a VLS-1U Rackmount?

To use the VERACITY HIGHWIRE LONGSTAR VLS-1P-CC in a VLS-1U Rackmount, you must remove the outer front mounting plate.

How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.

NO IMAGE CONTENT AT THIS TIME. PLEASE CHECK BACK LATER

CLICK HERE TO DOWNLOAD VERACITY HIGHWIRE LONGSTAR VLS-1P-CC (01) PDF DOCUMENT


Leave comments, questions, reviews, tips, tricks, hacks or page errors below. Account not required.