VAX RAPIDE SPRING V-135 (01) PDF MANUAL

The main parts of the V-135 Series carpet washer are:

Handle

Cord hooks

Power cord

Clean water tank release

Clean water tank

Dirty water tank lid

Wheels

Suction channel

Handle assembly release position

On/off switch

Handle release pedal

Vax Cleaning Solution

Do not leave the carpet washer unattended when plugged in. Unplug it from socket when not in use.

To prevent electric shock do not use outdoors.

Not to be used as a toy. Children should be supervised to ensure that they do not play with the appliance.

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety.

Use only as described in this manual.

Do not use with a damaged cord or plug. If the supply cord and/or plug is damaged, they must be replaced by the manufacturer, a Vax Service Agent or similarly qualified persons in order to avoid hazard.

Do not pull or carry by the cord, use the cord as a handle, allow the cord to come into contact with hot or sharp surfaces or close a door on the cord.

Do not unplug by pulling on the cord.

Do not handle the plug or carpet washer with wet hands.

Do not put any objects into openings or operate with openings blocked, keep them free of anything that may reduce airflow.

Keep hair, loose clothing, fingers and all parts of the body away from openings and moving parts.

Do not use the carpet washer on any glowing, burning or smoking particles.

Do not use without the solution tank and dirty water tank in place.

Turn off all controls before unplugging.

Do not use to pick up flammable or combustible liquids such as petrol, or use in areas where they may be present.

Keep the unit on the floor.

Do not use an extension cord.

Do not attempt to remove blockages with sharp objects as they may cause damage.

Store indoors put away after use to prevent tripping accidents.

Using improper voltage may result in damage to the motor and possible injury to the user. The correct voltage is listed on the rating label.

A hazard may occur if the carpet washer runs over the power supply cord.

To prevent dirty water from running into motor, do not hold the appliance upside-down or lay on its side. Use appliance in normal vacuuming position.

Use extra care when cleaning on stairs.

Do not carry appliance while motor is running.

Carpets should be dry vacuumed thoroughly before washing.

The unit must be unplugged from the mains socket outlet after use, and before cleaning or maintaining the unit.

This unit is not intended for commercial use.

Insert the middle frame into the machine base.

Insert one screw on either side of the middle frame to secure.

Slide the upper handle down onto the unit. The handle will click and lock in place.

Run the mains wire above the upper cord hook and secure with the cord clip.

Turn off the cleaner when emptying and filling the tanks and performing any maintenance.

Grasp the solution reservoir under the handle and press the handle release lever in.

Tilt the solution reservoir away from the cleaner and remove.

Unscrew the cap from the bottom of the solution reservoir.

Pour the correct amount of Vax Cleaning Solution as directed into the clean water tank.

Fill the remaining space in the solution reservoir with warm tap water. The maximum water temperature is 50°C.

Replace the measuring cap.

Use only Vax Cleaning Solution; using other cleaning solutions may cause excessive foaming, which can cause the float to shut off the cleaner prematurely and may invalidate your warranty.

Place the bottom of the solution reservoir into the cleaner and push into place. There will be an audible click when the reservoir is in the correct position.

Plug the cord into a mains electricity socket.

Turn the power switch on. The switch is located on the back of the cleaner, next to the handle release.

Press on the handle release pedal and pull the cleaner back into a reclined position.

Never leave the cleaner unattended with the power on.

Vacuum carpets thoroughly with a dry vacuum cleaner before washing.

Whilst depressing the solution spray trigger, push the carpet washer in a forwards motion.

Release the trigger and pull the unit backwards in the same path to remove dirty water and solution from the carpet.

Repeat if necessary. When the dirty water reaches the max fill line on the dirty water tank, empty the tank.

Unplug your cleaner before emptying the dirty water tank.

Grasp the top of the dirty water tank handle and press the release latch.

Grasp the handle and pull up the top of the base, taking care to ensure that no dirty water leaks from the front.

To empty the water tank, grasp the handle with one hand and the nozzle with the other, and empty into the sink.

The float in your Rapide is located forwards of the back of the dirty water tank lid. It will shut off the suction when the dirty water tank is full.

For best results, use a smooth, steady motion keeping the nozzle flat against the carpet. Tipping the cleaner and breaking the seal of the nozzle against the carpet will cause the float to rise, cutting off suction. Once the float is activated, empty the dirty water tank. If the tank does not appear full, turn off the power switch and wait for the float to settle. You will hear a change in motor pitch when the tank is full and needs emptying. For best results, use only Vax Cleaning Solution.

Rinse the dirty water tank and top thoroughly with warm water.

Allow them to dry fully before replacing them on your cleaner to prevent mildew.

Do not use any chemicals in the cleaning process.

Lift the front of the carpet cleaner base off the carpet with one hand.

Grasp the handle and hook the front of the dirty water tank into the base, making sure that the front of the dirty water tank is resting on the base.

While making sure the dirty water tank is resting on the base, place the rear of the tank into the base of the cleaner, push down on the handle until it latches.

Replace the top of the dirty water tank by pressing it into place.

Failure to install the dirty water tank correctly will result in poor dirty water pick up.

The plug must be removed from the socket outlet before cleaning or maintaining the appliance.

Flip the cleaner on its side to expose the nozzle base.

Lift out the floating brush bar by pressing the two latches and pulling it gently.

Replace the floating brushbar.

Remove the dirty water tank from the unit.

Remove the filter cover from the back of the tank.

Separate the filter from the filter cover.

The filter can be rinsed in warm water (max. 40°C).

Do not use any detergents or boiling water to wash the filters. Vax recommends checking the filters every time the dirty water tank is emptied.

All filters must be in place before using your machine.

Ensure the filter is fully dry before replacing it back into the machine.

To reduce the risk of personal injury, unplug the vacuum cleaner before performing maintenance or troubleshooting checks.

If the cleaner is not properly plugged into the electrical outlet, plug it in firmly.

If there is no electricity in the electrical outlet, check the fuse or breaker.

If the ON/off switch is not turned on, push the on/off switch to ‘on’.

If there is a blown fuse or tripped breaker, reset the circuit breaker or replace the fuse.

If the dirty water tank is full, switch off and unplug the cleaner, then empty the dirty water tank.

If the dirty water tank is not installed correctly, refer to the fitting information for replacing the dirty water tank.

If there is an obstruction in the hose/nozzle, remove the hose and clear the obstruction.

If the dirty water tank is full, switch off and unplug the cleaner, then empty the dirty water tank.

If the dirty water tank is not installed correctly, refer to the fitting information for replacing the dirty water tank.

If the solution tank is not installed correctly, make sure the tank is securely locked in place.

If the solution tank is not installed correctly, make sure the tank is securely locked in place.

If the solution tank is empty, refill the tank.

If the handle is not fitted correctly, ensure the handle is fitted correctly.

Voltage: 220-240V~50Hz

Wattage: 700 W

Capacity: Clean water tank – 2.6 litres, Dirty water tank – 1.8 litres

Cord length: 6m

Weight: 5kg

Specifications are subject to technical change without notice.