VACZON VZA01B109A-BLE (01) PDF Document

Please adhere to the following safety instructions:

1. To reduce the risk of fire, electric shock, or personal injury, mount directly to a structural framing member or to an outlet box marked acceptable for fan support of 15.9kg (35 lbs). For outlet box mounting, use mounting screws provided with the outlet box.

2. To avoid possible electrical shock, before installing or servicing your fan, disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel.

3. To reduce the risk of electric shock, this fan must be installed with an isolating wall control/switch.

4. Do not bend the blade brackets when installing the blade brackets, balancing the blades, or cleaning the fan. Do not insert foreign objects in between rotating fan blades.

5. Do not use replacement parts that have not been recommended by the manufacturer (e.g. parts made at home using a 3D printer).

6. Before installing the fan, disconnect the power by removing fuses or turning off circuit breakers.

7. Ensure all electrical connections comply with local law and the national electrical code. Hire a qualified electrician if you are unfamiliar with installing electrical wiring.

8. Make sure the installation site is roomy enough to allow fan blades to rotate. There must be at least seven feet from the floor to the fan blades’ tips.

9. If mounting the fan on a ceiling outlet box, use a metal outlet box secured directly to the building structure, capable of supporting at least 35 lbs. Do not use a plastic outlet box.

10. After installing the fan, make sure all the connections are secured so that the fan won’t fall.

11. Do not insert anything between fan blades while the fan is operating.

12. Turn the fan off and wait for it to stop before reversing the fan’s rotating direction.

13. To reduce the risk of electrical shock and personal injury, do not install the fan on a sloped ceiling and do not use this fan with any solid-state fan speed control device, or rheostat.

14. After making wire connections, the wires should be spread apart with the grounded conductor and the equipment-grounding conductor on one side of the outlet box and the ungrounded conductor on the other side. The splices should be turned upward and pushed carefully up into the outlet box.

15. To reduce the risk of electric shock, disconnect the electrical supply circuit to the fan before installing the light kit.

PARTS:

1 x Ceiling Bracket

1 x Ceiling Fan Body

1 x Downrod Ball

5 x Blades

1 x 6-inch Downrod

1 x 10-inch Downrod

1 x Canopy

1 x Light Kit

1 x Canopy Cover

1 x Light Shade

1 x Coupling cover

ACCESSORIES:

4 x ST5 x 35mm Wood screws

2 x 8-32UNC x 32mm Mounting screws

1 x Remote control & Remote control holder (Battery included)

4 x Plastic wire nuts

2 x Ø16 x Ø4.5 x 1.5mm Washers

1 x Controller

1 x Balanced parts package

2 x M4 Spring washers

2 x Screws

16 x M5 x 12 mm Blade screws

16 x Φ12 * Φ5 * 1mm Blade Washers

2 x Expansion screws

Tools Needed (Not Included):

Ladder

Phillips Screwdriver

Wire Stripper

Drill

Room Dimensions:

There must be a minimum of 7 feet from the bottom edge of the blade to the floor.

There must be a minimum of 30 inches from the blade tip to the nearest wall or obstruction.

Room Ceiling Angle:

Ensure your room ceiling angle is less than 15 degrees.

WARNING: To avoid possible electrical shock, before installing your ceiling fan, disconnect the power by turning off the circuit breakers to the outlet box associated with the wall switch location.

Option 1: Concrete ceiling

Use the 2 provided mounting screws and washers when securing to an existing ceiling fan-rated outlet box. Make sure it is securely installed and is acceptable for fan support of 15.9kg (35 lbs) or less.

Option 2: Wood ceiling

Use the 4 provided wood screws when securing to a support structure with an approved electrical outlet box. Drill 4 holes in the support structure to aid in securing the ceiling bracket.

WARNING: FAN FALL HAZARD. ALWAYS tighten the setscrew with a screwdriver. DO NOT hand tighten the setscrew. CHECK the setscrew is tight using a screwdriver each time you change fan direction.

Step 1: Remove the pre-installed setscrews and downrod pin from the motor assembly yoke.

Step 2: Insert the canopy, canopy cover, and coupling cover onto the downrod. Pass all the wires to one side of the horizontal bar in the downrod to prevent excessive wire tangling.

Step 3: Carefully slide the downrod into the yoke of the motor assembly. Align the holes in the downrod with the holes in the yoke. Carefully re-install the downrod pin and clip.

Step 4: Tighten the setscrew with a screwdriver.

Step 5: Put down the coupling cover over the yoke.

The downrod ball is pre-installed on the 6-inch downrod. If you wish to move it to the 10-inch downrod, follow these steps:

a. Loosen and remove the two screws on the downrod ball from the 6-inch downrod.

b. Lift the downrod upwards, then remove the horizontal bar, and detach the downrod ball from the 6-inch downrod.

c. Install the downrod ball onto the 10-inch downrod and securely insert the horizontal bar in its designated position.

d. Insert the first perforated long screw tightly, and then insert the second short screw tightly.

Step 1: Hang the Fan Body

Place the downrod ball into the ceiling bracket. Make sure the downrod ball slot matches the inner lock on the bracket. Rotate the downrod until it is secured.

Step 2: Wire the Fan

WIRING MUST BE UP TO CODE. All wiring must be in accordance with national and local electrical codes. If you are unfamiliar with wiring or in doubt, consult a qualified electrician.

a. Connect the wires from the ceiling to the controller using wire nuts (white to white, black to black).

b. Connect the 4 grounding wires (green wires) coming from the ceiling, downrod, controller, and ceiling bracket together using a wire nut.

c. Insert the motor wires and light wires into the controller by plugging them into the corresponding connectors.

d. Slide the controller between the mounting bracket and the top of the downrod. Note: Use the canopy to place the excess wires.

Step 3: Install the Canopy

Install the canopy to the screws of the mounting bracket, tighten the screws, and then slide the canopy cover up to cover the screws.

Insert the fan blade to the fan-motor assembly. Attach the blade to the fan blade bracket of the fan-motor assembly using the blade screws and washers provided, and tighten them firmly. Repeat for all 5 blades.

Step 1: Remove the 3 screws from the ceiling fan body’s mounting plate. Place the screws aside for subsequent use.

Step 2: Connect the wires of the ceiling fan body with the light kit by plugging them together. Attach the light kit to the ceiling fan body using the 3 screws removed in Step 1 and tighten them firmly.

Rotate the light shade clockwise to securely fasten it into place on the light kit.

Power Switch: Press to turn the power ON/OFF. Within 5 seconds after power on, hold press to match code.

Fan Speed Setting (Up Arrow): Press to increase fan speed from 1 to 6 levels.

Fan Speed Setting (Down Arrow): Press to decrease fan speed from 6 to 1 level.

Forward and Reverse (REV): Press to change the airflow direction. Within 5 seconds after power on, hold press to clear code.

Light Switch & CCT Setting (K ON/OFF): Press to turn the light ON/OFF. Hold press for 2 seconds to change the Color Correlated Temperature (CCT) to 3000K/4000K/6500K.

Fan CCT Setting (+): Press to increase light brightness (dimmer +).

Fan CCT Setting (-): Press to decrease light brightness (dimmer -).

Timer Settings (1H/2H/4H/8H):

Press once: fan auto off after 1hr

Press twice: fan auto off after 2hr

Press 3 times: fan auto off after 4hr

Press 4 times: fan auto off after 8hr

Within 5 seconds after turning the power on to the fan, press and hold the Power Switch button on the remote. When you hear a buzzing sound, the code match is successful. If it is not successful, please repeat the step.

1. Use the two holes on the holder as a guide to drill two corresponding holes in a flat wall.

2. Insert the two provided expansion screws into the holes and make them level with the flat wall.

3. Align the two holes on the holder with the two holes on the wall. Insert the two screws into the holes and tighten them using a screwdriver.

4. Store your remote control in the holder.

First, open the battery cover to remove the insulation spacer before first use.

To replace the battery:

1. Remove the screw from the battery cover on the remote control using a Phillips head screwdriver.

2. Pull up and remove the battery cover.

3. Remove the old battery and replace it with a new CR2032, 3V lithium battery, ensuring correct polarity.

4. Reinstall the battery cover and secure it with the screw.

WARNING: INGESTION HAZARD. This product contains a button cell or coin battery.

KEEP new and used batteries OUT OF REACH OF CHILDREN.

DEATH or serious injury can occur if ingested. A swallowed button cell or coin battery can cause Internal Chemical Burns in as little as 2 hours.

Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.

Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.

Call a local poison control center for treatment information.

Compatible battery type is CR2032, 3V.

Ensure the batteries are installed correctly with regard to polarity (+ and -).

Do not mix old and new batteries, different brands or types of batteries.

Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

Step 1: Scan the QR code in the manual or search “FanLamp Pro” from the App Store or Google Play to download the app.

Step 2: Turn on Bluetooth on your phone.

Step 3: Add device, name the fan light, and choose the room for your fan.

Step 4: Pair the code with the app. Click the pairing button in the app within 5 seconds of the light turning on. If the light flicks or you hear a beep, it means the fan and app successfully paired. The APP Control Distance is within 65ft (20m).

Pairing Button: Initiates the pairing process with the fan.

Adjust Fan Speed: A circular slider to adjust fan speed from 0 to 6.

Adjust Light Brightness: A slider to adjust the light’s brightness level.

Adjust Light CCT: A slider to change the light’s color temperature.

Timer Setting Mode: Allows you to set a timer for the fan to turn off.

Natural Wind Mode: Simulates a natural breeze by varying fan speed.

Sleep Wind Mode: A gentle fan mode for sleeping.

Reverse Rotation: The fan rotates in reverse to distribute warm air throughout a room.

Forward Rotation: The fan rotates forward for a cooling downdraft.

White light / Natural light / Yellow light: Presets for different light color temperatures.

Night light: Sets the light to 10% brightness.

Power Switch: Turns the entire unit ON/OFF.

Light Switch: Turns the light ON/OFF.

Fan Switch: Turns the fan ON/OFF.

Clean the motor housing and blades with a soft brush or lint-free cloth to avoid scratching the finish.

At least twice each year, lower the canopy to check the downrod assembly and tighten all screws on the fan.

Important safety reminders:

Shut off the main power supply before you begin any maintenance task.

DO NOT use water or a damp cloth to clean the fan.

Cleaning products may damage the finishes.

Make sure the power switch is on.

Check the circuit breaker to ensure the power is turned on.

Make sure the blades spin freely.

Turn off power from the circuit breaker, then loosen the canopy and check all the connections according to the wiring diagram.

Make sure the blades are properly installed on the ceiling fan body.

Turn the power off, support the fan carefully, and check that the downrod ball is properly seated in the mounting bracket.

Make sure the battery is installed correctly. If the command indicator light keeps flashing, this indicates a low battery. Install a fresh battery.

The battery may be weak. Change the battery in the remote control.

Make sure the blades are properly installed.

Check to see if any of the blades are cracked. If so, replace all of the blades.