U-LINE ECHELON 2175BEVOL (01) PDF MANUAL

U-LINE ECHELON 2175BEVOL (01) PDF SUMMARY:

What general precautions should I take when using this appliance?

Use this appliance for its intended purpose only and follow the general precautions listed throughout the PDF.

---

What is required for electrical grounding?

This unit requires connection to a grounded (three-prong), polarized receptacle that has been placed by a qualified electrician in accordance with applicable electrical codes.

---

What should I avoid doing with the electrical components of this unit?

• Keep the unit unplugged throughout installation except during testing.
• Never remove the round grounding prong from the plug and never use a two-prong grounding adapter.
• Never use an extension cord to connect power to the unit.

---

What precautions should I take when moving and handling the unit?

• Use care when moving and handling the unit. Use gloves to prevent personal injury from sharp edges.
• Do not lift the unit by the door or door handle.
• Do not install the unit behind closed doors or in any way that would obstruct airflow to the front grille, which may cause the unit to malfunction.

---

What is included in the carton when I receive my unit?

You will receive a carton containing your 2175BEVS or 2175BEVOL Beverage Center with a package inside containing a Use and Care Guide, a Product Registration Card and an Anti-Tip Bracket Installation Kit. 2175BEVOL units are shipped with a cardboard-wrapped door and an additional package of hardware.

---

What should I do after I install my unit?

Keep the Use and Care Guide and the Installation Guide in a safe place for future reference.

---

What should I do with the protective coating on Stainless Steel units?

When inspecting/installing a Stainless Steel unit, the protective coating covering the unit must be removed first. Start at a corner of the unit/door and pull back the protective coating to remove it from the unit/door.

---

How should I clean the stainless steel surfaces after removing the protective coating?

Clean all Stainless Steel surfaces with Claire Stainless Steel Polish and Cleaner or comparable product or a mild detergent and warm water solution and soft cloth. Do NOT use abrasive cleaning agents. If cleaning with a mild detergent and warm water solution and soft cloth, the unit MUST be treated with Claire Stainless Steel Polish and Cleaner or comparable product to prevent discoloration.

---

How do I clean the exterior of overlay models?

The door, grille, and cabinet may be cleaned with a mild detergent and warm water solution. Do not use solvent-based or abrasive cleaners. Use a soft sponge and rinse with clean water. Wipe with a soft, clean towel to prevent water spotting.

---

What should I avoid when cleaning stainless steel models?

• Do not clean with steel wool pads.
• Do not use cleaners that are not specifically intended for stainless steel (this includes glass, tile and counter cleaners).
• Use of abrasive pads such as Scotchbrite will cause the graining in the stainless to become blurred.

---

What should I do if rust appears on stainless steel surfaces?

If any surface discolors or rusting appears, clean it quickly with Bon-Ami or Barkeepers Friend Cleanser and a non-abrasive cloth. Always clean in the direction of the grain. Always finish this process with Claire Stainless Steel Polish and Cleaner or comparable product to prevent further problems. Rust that is allowed to linger can penetrate into the surface of the stainless steel and complete removal of the rust may not be possible.

---

What are the clearance requirements for built-in installation?

When built-in, your unit does not require additional air space for top, sides or rear. However, the front grille must NOT be obstructed and clearance is required for electrical connection in the rear. The unit can NOT be installed behind a closed cabinet door.

---

How wide should the cut-out be for installation?

The 24-3/16" width allows 1/4" for ease in installation and removal of the unit.

---

How deep is the unit?

The unit is 23-1/4" deep including the wood overlay frame on 2175BEVOL models and 23-1/4" deep including the door and not the handle on Stainless Steel models.

---

What is the door clearance for Wood Overlay units?

Wood Overlay units have a zero clearance for the door to open 90°.

---

What is the door clearance for Stainless Steel models?

Stainless Steel models require a minimum of 2-1/8" door clearance to accommodate the handle if the unit is installed next to a wall or similar type of structure.

---

What are the power supply requirements?

The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A circuit (normal household current).

---

What are the environmental requirements for operation?

• The units are designed to operate between 50°F (10°C) and 110°F (40°C). High ambient temperatures (110°F [40°C] or higher) may reduce the unit’s ability to reach low temperatures.
• For best performance, keep the unit out of direct sunlight and away from heat-generating equipment.
• In climates where high humidity and dew points are present, condensation may appear on outside surfaces. This is considered normal. The condensation will disappear when the humidity drops.

---

What are the cut-out width requirements for side-by-side installation?

Cut-out width for a side-by-side installation is the total of the widths listed under Cut-Out Dimensions in each unit’s Installation Guide.

---

What space is required between units in a side-by-side installation?

1/4-inch space needs to be maintained between the units to ensure unobstructed door swing.

---

What are the electrical requirements for side-by-side installation?

Units must operate from separate, properly grounded electrical receptacles placed according to each unit’s Electrical Specifications.

---

What is the wood trim on the wine racks coated with?

The wine racks are coated at the factory with a clear vinyl sealer.

---

What should I do before staining or finishing the wood trim?

To prevent permanent damage to the inner liner of the Beverage Center, the wine rack wood trim MUST be removed from the unit for staining and/or finishing. Allow stain/finish to dry thoroughly (at least 24 hours per coat) in accordance with the stain/finish manufacturer’s instructions prior to re-installing the wood trim inside the cabinet of the Beverage Center.

---

How do I remove a wine rack from the cabinet?

1. Grasp the end of the rack, and gently slide it out until it stops.
2. Remove any bottles stored on the rack.
3. Press the left rack release lever down, and at the same time, lift the corresponding right rack release lever up, and pull the rack out until it is free of the tracks and the cabinet.

---

How do I insert a rack in the cabinet?

1. Align the left and right rack channels with the tracks in the cabinet, and ensuring an even track engagement on both sides, gently push the rack into the cabinet until it stops.
2. Before reloading the rack, ensure proper operation of the travel stops in the left and right track rails by pulling the rack out gently until it completely stops.

---

How do I remove the wood trim surrounding the controller?

1. Loosen the two screws holding the controller to the mounting bracket.
2. Lift the controller housing and then rotate forward to expose the wiring harness on the back.
3. Disconnect the wiring harness from the controller.
4. Remove the two screws holding in the controller housing, then remove from the wood.

---

What should I be careful of when removing the controller?

Carefully remove the controller from the housing. The glass front is not secured to the controller. Glass may fall and break, which is not covered under warranty.

---

What should I do before applying a final finish to the wood trim?

If staining the trim is desired, it must be done before the application of any type of final finish.

---

What type of stain should I avoid using on wood trim?

DO NOT use oil-based stains on wood trim. Vapors from oil-based stains will permanently penetrate the liner and will not dissipate over time.

---

How do I apply water-based stain to the wood trim?

1. Apply Minwax® Water-Based Wood Stain to wood with a synthetic bristle brush or a foam applicator.
2. Allow stain to penetrate approximately three minutes.
3. Before the stain is dry, take a stain dampened rag and remove any excess stain remaining. Wipe in the direction of the grain with medium pressure to achieve the desired stain color.
4. After two hours, repeat to even out the color of the wood.

---

How long should the stain dry before applying the final finish?

Allow stain to dry for a minimum of three hours before applying the final finish.

---

How do I apply the final finish to the wood trim?

1. Remove all dust from the wood, and apply one coat of Minwax® Polycrylic® Protective Finish using a synthetic bristle brush to the wood.
2. Apply the finish in a thin coat following the direction of the grain.
3. Apply the finish to the back and sides of the wood first, and allow it to dry for two hours.
4. Apply the finish to the front side of the wood next, and allow it to dry for two hours.
5. Sand with very fine 220 grit sandpaper.
6. Apply two additional coats of the finish in the same manner, but do not sand the trim after the final third coat is applied.

---

How long should the final coat dry before reinstalling the trim?

Allow the final coat to dry for 24 hours before reinstalling the trim to the cabinet interior components.

---

How do I apply a final finish only?

1. Remove all screws securing wood trim to interior components, and remove the trim.
2. Lightly scuff sand the wood trim with 280 or finer grit sandpaper.
3. Remove sanding dust with a clean, dry cloth.
4. Apply a thin coat of a clear, protective finish, following the container label directions.
5. Lightly sand and reapply if desired.

---

How long should the final coat dry before reinstalling the trim?

Allow the final coat to dry for 24 hours before reinstalling the trim to the cabinet interior components.

---

How do I reverse the door on overlay units?

1. Remove screws from the new hinge location.
2. Remove the top hinge, install the hinge screw pin, and remount on the opposite side bottom. Be sure to also relocate the backing plate located behind the hinge.
3. Remove the two door closer inserts from the additional package of hardware and install as shown on the new bottom hinge.
4. Remove the existing bottom hinge and remount on the opposite side top. Be sure to also relocate the backing plate located behind the hinge.
5. Remove pivot plate, flip it over, and remount on the opposite side of the door.
6. Holding the door upright with the top of the door tilted forward, place the hole of the door pivot plate on the bottom hinge screw pin.
7. Tilt the top of the door into position in the top hinge and install the top hinge screw pin.
8. Install plastic screw plugs removed in step 2 in old hinge holes.

---

What is the required thickness of the wood overlay frame?

The thickness of the wood overlay frame must be 3/4". The door frame must not weigh more than 20 lbs.

---

How do I create the relief for the pivot plate?

Create a relief for the pivot plate by cutting a notch in the top corner and coinciding back corner of the overlay frame. Refer to Figure 15 for exact specifications.

---

How do I prepare the door for an overlay frame?

1. Lay the door on a clean, flat surface with the gasket facing up.
2. Pull the gasket completely out of the groove. Start in the middle and pull outward, moving toward the edge.

---

How do I check the overlay fit?

1. Turn the door over and lay the overlay frame on the front side of the door. Make sure the frame is fully seated on all four sides.
2. Visually check for a gap between the frame and glass.

---

How do I apply foam tape to the overlay frame?

1. Cut foam tape into four pieces, two pieces the width of the overlay frame and two pieces the height of the overlay frame.
2. Remove the adhesive protection strip from one piece of the foam tape and align to the edge of the overlay frame, adhering the foam tape to the overlay frame.
3. Trim each piece of tape immediately after application.

---

How do I attach the overlay frame?

1. Tap nylon inserts into the top holes drilled in the overlay frame. Use two #6 screws to attach the top pivot bracket to the overlay frame.
2. If a user-supplied cabinet handle will be used, attach its hardware to the overlay frame.
3. Secure the front of the door to the back of the overlay frame using tape on all four corners. Make sure all four edges are aligned.
4. Place the door and overlay frame on a flat, clean protective surface. Use the door frame holes as a guide to lightly punch pilot holes for the #6 x 1" pan-head screws.
5. Attach the door to the overlay frame using the #6 x 1" wood screws.
6. Remove all traces of tape securing the overlay frame to the door frame.
7. Starting at the corners and working toward the center, push the door gasket back into place. Make sure the gasket is seated on all four sides.

---

How do I install the door?

1. Insert the pivot post into the bottom hinge, making sure to tighten only until the post is level with the outside of the hinge.
2. Install the door closer, making sure that the bosses on the closers align with the holes in the hinge.
3. Holding the door upright with the top of the door tilted forward, place the hole of the pivot plate onto the bottom hinge screw pin. Be sure that the bosses on the closers align with the holes in the pivot plate.
4. Tilt the top of the door into position and install the top hinge screw pin. Tighten only until the post is level with the top of the hinge.

---

How do I check door alignment?

Properly aligned, the door should be 1/8" below the top of the unit’s cabinet, NOT flush with the top. Compare the top edge of the door to the top edge of the cabinet.

---

How do I adjust the door alignment?

1. Remove the top hinge screw pin. Remove the door by tilting forward and lifting off the bottom hinge pin.
2. With the door upside-down, loosen but do not remove the two screws on the door’s bottom hinge plate.
3. If the top far edge of the door needs to move UP, move the hinge plate toward the outside of the door and retighten screws. If the top far edge of the door needs to move DOWN, move the hinge plate toward the inside of the door and retighten screws.
4. Mount the door to recheck alignment and repeat if further adjustment is necessary.
5. When the top edge of the door is parallel to the top edge of the cabinet, remove the door and ensure the two screws are secure.
6. Remove the door closers from the bottom hinge, clean thoroughly, and lubricate the mating surfaces with petroleum jelly.
7. Reinstall the closers, lining up the bosses with the holes in the hinge and hinge plate.
8. Mount the door and install the top hinge pivot pin.

---

What are the electrical specifications?

The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A power supply (normal household current).

---

What should I avoid doing with the electrical components of this unit?

• Never remove the round grounding prong from the plug and never use a two-prong grounding adapter.
• Never use an extension cord to connect power to the unit.

---

How do I level the unit?

1. Use a level to check the levelness of the Beverage Center from front to back and from side to side.
2. If the Beverage Center is not level, adjust the feet on the corners of the unit as necessary.
3. Check the levelness after each adjustment and repeat the previous steps until the unit is level.

---

What should I do if the room floor is higher than the floor in the cut-out opening?

Adjust the rear feet to achieve a total unit rear height of 1/8" less than the opening’s rear height. Shorten the unit height in the front by adjusting the front feet. This allows the unit to be gently tipped into the opening. Readjust the front feet to level the unit after it is correctly positioned in the opening.

---

What should I do if the door remains open unless it is pushed closed?

Make sure the closers (at the bottom of the hinge pin) are clean, greased, and installed correctly. Also, re-check leveling from front to back of the unit and readjust if necessary. Make sure that the pivot plate is installed correctly.

---

What should I do if the unit does not appear to turn on when plugged in?

Make sure the outlet has power (circuit breaker has not tripped). Check to see that the control is turned on.

---

What should I do if the light is on with the door closed?

Touch the LIGHT icon on the display panel. This will cancel out the light function and just allow the light to turn on and off with the door opening and closing. The Beverage Center has an interior light that is illuminated when the door is opened. The light can be left on while the door is closed by pressing the LIGHT icon. This will turn interior light on for 4 hours, then it will turn off.

---

Where is the Model and Serial Number plate located?

The Model and Serial Number plate is located inside the unit at the upper right-hand corner.

---

How can I locate a service company?

You can go online at http://www.U-LineService.com and search for a service company by zip code.