TYAN FT65T-B8030 (01) PDF DOCUMENT

Before you begin installing your TYAN FT65T-B8030 server system, please follow these precautions:

1. Make sure to read all precautions and instructions before you start installing the server system.

2. Refer all servicing to qualified personnel to avoid the risk of damage to the server system.

3. Exercise normal ESD (Electrostatic Discharge) procedures during system integration. It is recommended to wear gloves and an anti-static wrist strap to avoid possible damage to the equipment.

4. The current processor socket design places the pins on the motherboard instead of the processor itself. Exercise caution when installing the processors as the manufacturer’s warranty does not cover damage inflicted upon the motherboard, including damage to the CPU sockets.

The box content for the TYAN FT65T-B8030 includes the following items:

Box Content:

(1) Chassis

(1) TYAN® S8030GM4NE-2T or S8030GM4NE Mother Board (pre-installed)

(3) Fan + (2) Rear Fan (for -N sku) or (3) Fan (for -G sku) (pre-installed)

(1) Power Supply FSP2000-52AGPBI

(1) HDD BP M1309F65T-BP12-8 (pre-installed)

(1) HDD BP M1298T65-BP12E-2 (pre-installed)

(1) M1713G24-FPB (pre-installed)

Accessories:

(1) CPU Heatsink

(1) US Power Cord

(1) EU Power Cord

(3) Screw Pack

(4) GPU Holder BKT

(1) GPU Support BKT

(2) M.2 Latch

(1) Quick Installation Guide

To avoid integration difficulties and possible board damage, your TYAN FT65T-B8030 system must meet the following minimum requirements:

Processor: AMD EPYC 7002/7003 series processor w/ TDP up to 240W

Memory Type: (8) DDR4 DIMM slots (8x memory channels) Support 2TB RDIMM/LRDIMM DDR4 3200 memory

Hard Disk Drives: (8) hot swap 3.5″/2.5″ SAS 12Gb/s and SATA 6G, (2) 2.5″ SATA 6Gb/s and NVME

Rack Mount Kit: Standard 19″ equipment rack

The following tools are required for the installation:

Phillips Screwdriver

T20 Torx Screwdriver

Anti-Static Wrist Strap

To open the chassis of your TYAN FT65T-B8030, follow these steps:

1. Place your TYAN® Server Chassis on a flat anti-static surface. Read and follow normal ESD (Electrostatic Discharge) procedures before proceeding.

2. Remove the screw and loosen the thumb screws on the rear of the chassis.

3. Slide the top cover and remove.

NOTE: Please refer to the user’s manual for the power cord connection method.

To install a 3.5″ or 2.5″ hard disk drive into the front of your TYAN FT65T-B8030, follow these steps:

1. Press on the locking lever latch. The locking lever will open automatically.

2. Slide the HDD tray out of the chassis.

3. To install a 3.5″ HDD: Unlock and open the tray locking lever. Place the 3.5″ HDD into the tray. Close the locking lever to secure the HDD to the tray.

4. To install a 2.5″ HDD: Place a 2.5″ HDD into the tray. Use 4 screws to secure the HDD to the tray.

5. Reinsert the HDD tray into the chassis.

6. Press the locking lever to secure the HDD tray. Repeat the same procedures to install other HDD trays.

To install a processor in your TYAN FT65T-B8030, follow these steps carefully:

1. Use a T20 Torx screwdriver to loosen the screws securing the force frame in a sequential order (3 -> 2 -> 1). The force frame will automatically eject after the captive screws are being released.

2. By placing both of your index fingers on the sides of the metal handle, pull to release the rail frame. Then lift the rail frame to its fully open position.

3. Remove the external cap from the rail frame. NOTE: Keep this cap for future DOA/RMA usage.

4. Align and install the carrier frame with the processor package into the slot on the rail frame.

5. During installation, observe the following: make sure to push the carrier frame with the package towards the end of the rail frame until it clicks into place, and do not drop the carrier frame or touch the package pad to avoid component damage.

6. Using your thumb and forefinger, remove the PnP cap by lifting it up vertically. NOTE: Keep this cap for future DOA/RMA usage.

7. Carefully close the rail frame with the installed package. Then push both edges of the rail frame firmly until it locks in place.

8. Close the force frame. Then use a T20 Torx screwdriver to tighten the screws to secure the force frame in a sequential order (1 -> 2 -> 3).

To install the CPU heatsink on your TYAN FT65T-B8030, follow these steps:

1. Align and install the CPU heatsink onto the top of the CPU socket.

2. Use a T20 Torx screwdriver to tighten the heatsink screws.

3. Connect the heatsink power cable to the mainboard connector.

To install memory modules (DIMMs) in your TYAN FT65T-B8030:

1. Unlock the clips on the sides of the DIMM slot.

2. Insert the memory module into the slot, ensuring it is correctly oriented.

3. Push down on the module until the clips lock into place.

To install an optional add-on card with the riser bracket, follow these steps:

1. Remove the four screws securing the riser bracket to the chassis. Then remove the riser bracket. CAUTION: Carefully remove and flip the riser bracket because the cables are still connected.

2. Remove the screw and slide to remove the PCIe dummy bracket.

3. Insert the add-on card into the riser bracket. Make sure the add-on card is latched into the riser bracket. Then secure the add-on card to the riser bracket with a screw.

4. Align and install the riser bracket to its slot on the chassis. Then secure the riser bracket to the chassis with four screws.

To install an optional Graphics Processing Unit (GPU) card, follow this procedure:

1. Remove the screw and slide to remove the PCIe dummy bracket. Repeat the same procedures to remove another PCIe dummy bracket if necessary.

2. Align and install the GPU holder bracket to the GPU card. Then secure the holder bracket to the GPU card with three screws.

3. Connect the GPU card into the PCIe slot on the motherboard. Secure the GPU card assembly to the chassis with four screws.

4. Connect one end of the power cable to the power connector on the GPU card and the other end of the power cable to the dedicated connector on the power supply unit (PSU).

The LEDs on the motherboard have the following functions:

i. ID LED

ii. HDD Active LED

iii. BMC LED

The external I/O ports on the rear of the TYAN FT65T-B8030 are as follows:

ID Button

USB3.1 (x2)

COM Port

Dedicated IPMI RJ45 LAN Port #5 (LAN5)

VGA Port

RJ45 LAN Port #4 (LAN4)

RJ45 LAN Port #3 (LAN3)

RJ45 LAN Port #2 (LAN2)

RJ45 LAN Port #1 (LAN1)

Yes, please save and replace the PnP Cap (Processor and Package cap) when returning the server board for service. This is important for DOA/RMA processing.