TRENDNET TPE-224WS (03) PDF Document

The package for the TRENDNET TPE-224WS contains the following items:

• TPE-224WS

• Quick Installation Guide

• CD-ROM (Utility and User’s Guide)

• Power cord

• Rack mount kit

The minimum requirements for setting up the TRENDNET TPE-224WS are:

• A computer with an Ethernet port and a web browser.

• A network cable.

You can use the following optional equipment with the TRENDNET TPE-224WS:

• EIA standard 19″ rack

• SFP modules (e.g., TE100-MGBFX, TEG-MGBSX, TEG-MGBS10, TEG-MGBS40, TEG-MGBS80, TEG-MGBS10D3, TEG-MGBS10D5, TEG-MGBS40D3, TEG-MGBS40D5)

To perform the initial hardware installation and configuration, follow these steps:

1. Connect the power cord to the TRENDNET TPE-224WS and plug it into a power outlet.

2. Connect your computer to one of the LAN ports on the switch using a network cable.

3. Assign a Static IP address to your computer’s network adapter in the subnet of 192.168.10.x (e.g., 192.168.10.25) and a subnet mask of 255.255.255.0.

4. Open your web browser, type the IP address of the switch in the address bar, and then press Enter. The default IP address is 192.168.10.200.

1. After accessing the switch’s IP address in your web browser, enter the User name and Password, and then click Login. The default credentials are:

• User Name: admin

• Password: admin

Note: The User Name and Password are case sensitive.

2. Click System and then click IPv4 Setup.

3. Configure the switch to match the requirements of your network. Then click Apply.

4. A warning message will appear stating that the management session will be disconnected. Click OK.

To permanently save your settings, follow these steps:

1. Click Save Settings to Flash in the menubar.

2. Click the Save Settings to Flash button.

3. A confirmation message “Save configuration finished” will appear. Click OK.

For detailed information regarding the TPE-224WS’s configuration and advanced settings, please refer to the User’s Guide on the provided CD-ROM.

Before using your TRENDNET TPE-224WS for the first time, it is essential to read and understand all safety and operating instructions. Keep these instructions in a safe place for future reference.

• Only operate TRENDnet devices using a mains power supply.

• To disconnect devices from the mains supply, remove the device itself or its mains plug from the power outlet. The power outlet and all connected network devices should be easily accessible so that you can pull the mains plug quickly if needed.

• TRENDnet devices are designed for indoor use only and in a dry location (except those that are rated for outdoor applications).

• To clean a TRENDnet device, disconnect it from the mains supply first and only use a dry towel.

If damage occurs, disconnect the TRENDnet device from the power outlet and contact a qualified technician ONLY. Damage is defined as:

• if the power cable/plug is damaged

• if the device has been submerged in liquid (e.g. rain or water; except products that are rated for outdoor applications)

• if the device is inoperable

• if there is damage to the housing of the device

Warning: Never open TRENDnet devices. Doing so poses the risk of electric shock! The device is voltage free only when unplugging from the mains power supply. No physical maintenance of TRENDnet devices is required.

To prevent overheating, follow these guidelines:

• Never expose TRENDnet devices to extreme heat (e.g. direct sunlight, fire, or other heat sources).

• Do not interlock multiple TRENDnet devices.

• Only install TRENDnet devices in locations with adequate ventilation (slots and openings on the housing are used for ventilation).

• Do not cover TRENDnet devices when operating.

• Do not place any objects on TRENDnet devices.

• Do not insert any foreign objects into the openings of TRENDnet devices.

• Do not place TRENDnet devices next to an open flame (e.g. fire or candles).

• Do not expose TRENDnet devices to direct heat (e.g. radiator or direct sunlight).

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.

(2) This device must accept any interference received, including interference that may cause undesired operation.

Note for PoE Products: This product is to be connected only to PoE networks without routing to the outside plant.

Note on Modifications: The Manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. Such modifications could void the user’s authority to operate the equipment.

Waste electrical and electronic products must not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or Retailer for recycling advice.