TRAIL TECH ENDURANCE II (01) PDF MANUAL


Post questions, comments, reviews or errors in the comment box below.

Your File is Ready … Download PDF

CLICK HERE TO DOWNLOAD TRAIL TECH ENDURANCE II (01) PDF MANUAL


PDF Content Summary: ENDURANCE II QUICK-START GUIDE 1. BUTTONS OVERVIEW: 2. SETTINGS MENU: To enter Endurance II set up menu, press and hold buttons 1, 2, and 3 for three seconds. Make sure to press and hold all 3 buttons at the same time! Set Distance: Select unit setting using button 1 or 2. (KM/H or M/H) 3. QUICK RESETS: Screen 1: DST • Press and hold buttons 1 & 2 for three seconds to reset DST. • Press and hold button 3 to enter DST adjustment. Use buttons 1 & 2 to increment and decrement your DST. Press button 3 to return to main screen. Set Clock Format: Select desired clock format using button 1 or 2. (12HR or 24HR) Select Maintenance Reminder Method: Select maintenance method. ODO = Mileage Odometer ART = Accumulated Ride Time Set Tire Size: Set Time Of Day: Select Maintenance Choose your tire size using button 1 Set your clock to desired time of day Reminder Interval: or 2. Note: To determine proper tire using button 1 or 2. Set interval time or mileage size see: “Wheel Sensor” installation duration. Note: Represents either instructions sheet. accumulated hours or mileage until maintenance, based on previous menu selection (ART or ODO.) Screen 2: DST2 • Press and hold buttons 1 & 2 for three seconds to reset DST2, Ride Time, & AVG Speed. • Press and hold button 3 to enter DST2 adjustment. Use buttons 1 & 2 to increment and decrement your DST2. Press button 3 to return to main screen. Screen 3: ODO • Press and hold buttons 1 & 2 to reset Max Speed. • To view time remaining until service maintenance interval icon is activated press and hold Button 3 for three seconds. • When the maintenance icon is displayed, hold button 3 for three seconds to enter maintenance interval screen (to reset, hold button 1 & 2 for three seconds.) 2000-MANUAL Tech Support: (844) 378-8143 technicalservice@apexproductgroup.com BUTTON 3 Next Setting BUTTON 1 Increment Up BUTTON 2 Increment Down

2000-MANUAL Tech Support: (844) 378-8143 technicalservice@apexproductgroup.com POWER CONNECTION: Wired to Vehicle Battery: • Connect the power wire to the vehicle 12V battery and to Endurance II. • A 1A fuse (not provided) should be used between the power cable and positve battery terminal when connecting directly to a battery. • Use zip-ties to secure the cable to the bike as it is routed to Endurance II. • Connect the red wire to the positive(+) battery terminal, and the black wire to the negative(-) battery terminal. Endurance II is polarity independent, so it cannot be installed backwards. System Tap: Tap into the electrical system at the lights, ignition, or CDI. When tapping into the electrical system, connect to a fuse protected circuit. Make sure power is not interrupted by the key switch when making the connection. MX Bikes: Motocross bikes do not have 12 volt power. For connection to an MX bike, connect power leads to ignition power leads from stator. Use caution, as this is a high voltage option. POWER NOTES: 1. Wakes on external power from bike. 2. Wakes on wheel movement. 3. Wakes on button press. 4. On external power backlight shuts off after 90 seconds of inactivity. 5. After 180 seconds of inactivity only clock will be displayed. Endurance II will operate in the range of 9.0-55VDC/9.0-400VAC, but will not draw enough power to drain a vehicle battery. SENSOR POWER Power Wire


FREE ENGLISH PDF

OPERATING INSTRUCTIONS

USER GUIDE - USER MANUAL

OWNER GUIDE - OWNER MANUAL

REFERENCE GUIDE - REFERENCE MANUAL

INSTRUCTION GUIDE - INSTRUCTION MANUAL

Leave a Reply