TOSHIBA RAC-PD1414CWRU (01) PDF DOCUMENT

The Timer button is used to initiate the AUTO ON start time and AUTO OFF stop time program. The timer on or off light will illuminate depending on the selected setting.

The Fan button controls the fan speed. Press to control the fan speed in four steps: LOW, MID, HIGH, and AUTO. The selected fan speed light (except AUTO) will illuminate. When AUTO is selected, no lights will illuminate.

For models with the Constant Fan feature, in COOL or DRY mode, press the Fan button for 3 seconds to turn on or off the constant fan function.

When the function is turned on, the constant fan light will illuminate, identifying the fan continuous run for cooling. When the function is turned off, the constant fan light will go out, identifying the fan cycle run with compressor stop.

The Mode button selects the desired operating mode. Each time you press the button, a mode is selected in a sequence that goes from AUTO, COOL, DRY, FAN, and HEAT (cooling only models excluded). The mode light illuminates and indicates the selected mode. To change between °F or °C, simultaneously press and hold the Up and Down buttons for 3 seconds.

The Up and Down buttons are used to increase/decrease temperature settings in 1°F (or 2°F)/1°C increments in a range of 62°F/17°C to 86°F/30°C or the TIMER setting in a range of 0 ~ 24hrs.

To change between °F or °C, simultaneously press and hold the Up and Down buttons for 3 seconds.

The Power button is the power switch for turning the unit on/off.

The Sleep button is used to initiate the SLEEP operation.

The LED display shows the set temperature in °F (Degrees Fahrenheit) or °C (Degrees Celsius) and the Auto-timer settings. While on DRY and FAN modes, it shows the room temperature.

E1: Room temperature sensor error.

E2: Evaporator temperature sensor error.

E3: Condenser temperature sensor error (select models).

E4: Display panel communication error.

P1: Bottom tray is full. Connect the drain hose and drain the collected water away. If the protection code repeats, call for service.

When one of the malfunctions (E1, E2, E3, E4, P1) occurs, turn off the unit and check for any obstructions. Restart the unit. If the malfunction persists, turn off the unit and unplug the power cord.

Press the “MODE” button until the “COOL” indicator light comes on.

Press the ADJUST buttons Up (▲) or Down (▼) to select your desired room temperature. The temperature can be set within a range of 62°F-86°F (17°C-30°C).

Press the “FAN SPEED” button to choose the fan speed.

Press the “MODE” button until the “HEAT” indicator light comes on.

Press the ADJUST buttons Up (▲) or Down (▼) to select your desired room temperature. The temperature can be set within a range of 62°F-86°F (17°C-30°C).

Press the “FAN SPEED” button to choose the fan speed. For some models, the fan speed cannot be adjusted while in HEAT mode.

Press the “MODE” button until the “DRY” indicator light comes on.

While in this mode, you cannot select a fan speed or adjust the temperature. The fan motor operates at LOW speed.

Keep windows and doors closed for the best dehumidifying effect.

When you set the TOSHIBA RAC-PD1414CWRU air conditioner to AUTO mode, it will automatically select cooling, heating (cooling only models excluded), or fan only operation depending on what temperature you have selected and the current room temperature.

The TOSHIBA RAC-PD1414CWRU air conditioner will control room temperature automatically according to the temperature point set by you.

Under AUTO mode, you cannot select the fan speed.

Press the “MODE” button until the “FAN” indicator light comes on.

Press the “FAN SPEED” button to choose the fan speed. The temperature cannot be adjusted.

Do not connect the duct to a window.

When the unit is on, pressing the Timer button will initiate the Auto stop program. The TIMER OFF indicator light illuminates.

Press the Up (▲) or Down (▼) button to select the desired time.

Press the Timer button again within 5 seconds to confirm.

When the unit is off, press the Timer button to initiate the Auto start program. Pressing it again within five seconds will initiate the Auto stop program.

Press the Up (▲) or Down (▼) button to select the desired Auto start time.

Press or hold the Up (▲) or Down (▼) button to change the Auto time by 0.5 hour increments, up to 10 hours, then at 1 hour increments up to 24 hours. The control will count down the time remaining until start.

The system will automatically revert back to display the previous temperature setting if there is no operation within 5 seconds.

Turning the unit ON or OFF at any time or adjusting the timer setting to 0.0 will cancel the Auto Start/Stop timer program.

Should a malfunction occur, the Auto Start/Stop timed program will also be cancelled.

The SLEEP function is used to decrease energy use while you sleep. Pressing this button will increase (during cooling operation) or decrease (during heating operation, applicable models) 1°F/1°C after 30 minutes.

The temperature will again increase (cooling) or decrease (heating) by another 1°F/1°C after an additional 30 minutes. This new temperature will be maintained for 7 hours before returning to the originally selected temperature.

This ends the Sleep mode and the unit will continue to operate as originally programmed.

The SLEEP operation feature is unavailable in FAN or DRY mode.

The MyTemp feature can ONLY be activated from the remote control. The remote control serves as a remote thermostat allowing for precise temperature control at its location, which must be within 26 feet of the TOSHIBA RAC-PD1414CWRU air conditioner.

To activate the MyTemp feature, point the remote control towards the unit and press the MyTemp button. The remote’s display will show the actual temperature at its location. The remote control will send this signal to the air conditioner every 3 minutes until the MyTemp button is pressed again.

If the unit does not receive the MyTemp signal during any 7 minute interval, the unit will exit the MyTemp mode.

This feature is unavailable under FAN or DRY mode.

If the TOSHIBA RAC-PD1414CWRU unit shuts off unexpectedly due to a power outage, it will restart with the previously set function automatically when the power resumes.

After the TOSHIBA RAC-PD1414CWRU unit has stopped, it cannot be restarted until 3 minutes have elapsed. This is to protect the unit. Operation will automatically resume after 3 minutes.

During Dry modes, remove the upper drain plug from the back of the unit and install the drain connector (5/8″ universal female mender) with a 3/4″ hose (locally purchased). For models without a drain connector, just attach the drain hose to the hole. Place the end of the hose directly in the drain area you’re using.

For Heat Pump models, remove the middle drain plug from the back of the unit and install the drain connector (5/8″ universal female adapter) with a 3/4″ hose (not included). For models without the drain connector, attach the drain hose to the connector. Place the end of the hose in the drain area you’re using. In Heat Pump mode, the drain hose can be elevated up to 6ft (1.8m). Direct the hose toward the drain, making sure that there are no kinks that will restrict water flow. Place the end of the hose into the drain and make sure the end of the hose is directed downward. When the continuous drain hose is not used, ensure that the corresponding drain plug and knob are installed firmly to prevent leaks.

When the water level of the bottom tray reaches a predetermined level, the unit beeps 8 times and the digital display shows “P1.” At this time, the TOSHIBA RAC-PD1414CWRU air conditioning/dehumidification process will immediately stop; however, the fan motor will continue to operate (this is normal).

Carefully move the unit to a drain location, remove the bottom drain plug, and let the water drain away. Reinstall the bottom drain plug and restart the machine until the “P1” symbol disappears. If the error repeats, call for service. Be sure to reinstall the bottom drain plug firmly to prevent leakage before using the unit.

Make sure that you install your unit on an even surface to minimize noise and vibration.

The unit must be installed near a grounded plug, and the Collection Tray Drain (found on the back of the unit) must be accessible.

The unit should be located at least 19.7″ (50cm) from the nearest wall to ensure proper air conditioning.

Do not cover the Intakes, Outlets, or Remote Signal Receptor of the unit, as this could cause damage to the unit.

You will need a Phillips screwdriver, tape measure or ruler, knife or scissors, and a saw (optional, to shorten the window adaptor for narrow windows).

The kit includes: 1 Unit adaptor, 1 Exhaust hose, 1 Air exhaust passage, 3 Bolts, 4 Window Sliders, 4 Foam seal A (adhesive), 2 Foam seal B (adhesive), 2 Foam seal C (Non-adhesive), 1 set Security bracket and 2 screws, 1 Drain hose, 1 Drain hose adaptor (for heat pump mode only), 1 set Remote controller and battery (for remote control models only), and 1 Power Cord Buckle.

Press the exhaust hose into the Air exhaust passenger and unit adaptor, clamping automatically by the elastic buckles of the adaptors.

Insert the unit adapter side of the exhaust hose assembly into the groove of the air outlet on the back of the unit. Align the hook of the unit adapter with the seat on the air outlet and slide the assembly down until seated.

1. Depending on the size of your window, adjust the size of the window slider.

2. If the length of the window requires two or more window sliders, use the bolt to fasten the window sliders once they are adjusted to the proper length.

1. Cut the adhesive foam seal A and B strips to the proper lengths, and attach them to the window sash and frame as shown.

2. Insert the window slider assembly into the window opening.

3. Cut the non-adhesive foam seal C strip to match the width of the window. Insert the seal between the glass and the window frame to prevent air and insects from getting into the room.

4. If desired, install the security bracket with 2 screws as shown.

5. Insert the window slider adaptor into the hole of the window slider.

1. Cut the adhesive foam seal A and B strips to the proper lengths, and attach them to the window sash and frame as shown.

2. Insert the window slider assembly into the window opening.

3. Cut the non-adhesive foam seal C strip to match the window height. Insert the foam seal between the glass and the window frame to prevent air and insects from getting into the room.

4. If desired, install the security bracket with 2 screws as shown.

5. Insert the window slider adaptor into the hole of the window slider.

To ensure proper function, do not overextend or bend the hose. Make sure that there are no objects within 20in (~500mm) of the exhaust hose.

Always unplug the unit before cleaning or servicing.

Do not use flammable liquids or chemicals to clean the unit.

Do not wash the unit under running water; doing so causes electrical danger.

Do not operate the machine if the power supply was damaged during cleaning. A damaged power cord must be replaced with a new cord from the manufacturer.

For the TOSHIBA RAC-PD1414CWRU model, remove the upper filter by taking it out. Do not operate the unit without the filter because dirt and lint will clog it and reduce performance.

Be sure to clean the air filter every 2 weeks for optimal performance.

In households with animals, you will have to periodically wipe down the grill to prevent blocked airflow due to animal hair.

Clean the unit using a damp, lint-free cloth and mild detergent. Dry the unit with a dry, lint-free cloth.

Drain the unit’s water collection tray.

Run the unit on FAN mode for 12 hours in a warm room to dry it and prevent mold.

Turn off the unit and unplug it.

Clean the air filter according to the instructions. Reinstall the clean, dry filter before storing.

Remove the batteries from the remote control.

Be sure to store the unit in a cool, dark place. Exposure to direct sunlight or extreme heat can shorten the lifespan of the unit.

If the unit displays P1 Error Code, it means the water collection tray is full. Turn off the unit, drain the water from the water collection tray, and restart the unit.

If room temperature is lower than the set temperature in COOL mode, reset the temperature.

The air filter may be blocked with dust or animal hair. Turn off the unit and clean the filter according to the instructions.

The exhaust hose may not be connected or is blocked. Turn off the unit, disconnect the hose, check for blockage, and reconnect the hose.

The temperature setting may be too high; decrease the set temperature.

Make sure all windows and doors are closed.

The room area could be too large; double-check the cooling area.

Check the room for possible heat sources and remove them if possible.

The floor may not be level. Place the unit on a flat, level surface.

The air filter may be blocked with dust or animal hair. Turn off the unit and clean the filter according to the instructions.

This sound is caused by the refrigerant flow inside the unit and is normal.

The remote control model is RG57H4(B)/BGEFU1.

It has a rated voltage of 3.0V, powered by dry batteries (R03/LR03x2).

The signal receiving range is approximately 26 ft. (8 m).

It operates in environments with temperatures ranging from 23°F ~ 140°F (-5°C ~ 60°C).

The TOSHIBA RAC-PD1414CWRU air conditioning unit comes with two AAA batteries. To insert or replace them:

1. Slide the back cover of the remote control downward, exposing the battery compartment.

2. Insert the batteries, paying attention to align the (+) and (-) ends of the batteries with the symbols inside the battery compartment.

3. Slide the battery cover back into place.

For optimum product performance, do not mix old and new batteries, or batteries of different types. Do not leave batteries in the remote control if you do not plan on using the device for more than 2 months. Ensure used batteries are disposed of properly.

The remote control must be used within 26 feet (8 meters) of the unit.

The unit will beep when it receives a signal from the remote. Curtains, other materials, and direct sunlight can interfere with the IR signal receiver.

In order to properly transmit a command, the ON/OFF indicator must be illuminated on the remote’s display.

The operating temperature range for the TOSHIBA RAC-PD1414CWRU unit is 62°F-86°F (17-30°C). You can increase or decrease the set temperature in 1°F or 1°C increments.

1. To change the operating mode, press the MODE button until the desired mode appears on the remote’s display.

2. Set the desired temperature.

If the unit does not change when the button is pressed, check that the ON/OFF indicator is illuminated. If it is not, point the remote at the unit and press the ON/OFF button.

The TIMER ON function allows you to set a period of time after which the TOSHIBA RAC-PD1414CWRU unit will automatically turn on.

1. Press the TIMER ON button. By default, the last time period that you set and an “h” (indicating hours) will appear on the display. This number indicates the amount of time after the current time after which you want the unit to turn on. For example, if you set TIMER ON for 2 hours, “2.0h“ will appear on the screen, and the unit will turn on after 2 hours.

2. Press the TIMER ON button repeatedly to set the time that you want the unit to turn on.

3. Wait 2 seconds, then the TIMER ON function will be activated. The digital display on your remote control will then return to the temperature display.

The TIMER OFF function allows you to set a period of time after which the TOSHIBA RAC-PD1414CWRU unit will automatically turn off.

1. Press the TIMER OFF button. By default, the last time period that you set and an “h” (indicating hours) will appear on the display. This number indicates the amount of time after the current time after which you want the unit to turn off. For example, if you set TIMER OFF for 2 hours, “2.0h“ will appear on the screen, and the unit will turn off after 2 hours.

2. Press the TIMER OFF button repeatedly to set the time that you want the unit to turn off.

3. Wait 2 seconds, then the TIMER OFF function will be activated. The digital display on your remote control will then return to the temperature display.

Keep in mind that the time periods you set for both functions refer to hours after the current time. For example, if the current time is 1:00 PM, and you want the unit to turn on automatically at 7:00 PM and operate for 2 hours, then automatically turn off at 9:00 PM, you would set TIMER ON for 6.0 hours and TIMER OFF for 8.0 hours.

When setting the TIMER ON or TIMER OFF functions, up to 10 hours, the time will increase in 30 minute increments with each press. After 10 hours and up to 24, it will increase in 1 hour increments. The timer will revert to zero after 24 hours.

You can turn off either function by setting the timer to “0.0h“.

The SHORTCUT function is used to restore the current settings or resume previous settings.

When the remote controller is on, pushing this button will automatically revert the system back to the previous settings including operating mode, setting temperature, fan speed level, and sleep feature (if activated).

By pressing for more than 2 seconds, the system will automatically store the current operation settings including operating mode, setting temperature, fan speed level, and sleep feature (if activated).

The wireless module model is US-SK105.

It operates under the IEEE 802.11 b/g/n standard.

The antenna type is Printed PCB Antenna.

The frequency band is 2400-2483.5MHz.

The maximum transmitted power is less than 20 dBm.

Its dimensions are 41 x 24 x 5 (mm).

The operation temperature range is 0°C ~ 45°C (32°F ~ 113°F).

The operation humidity range is 10% ~ 85%.

The power input is DC 5V/300 mA.

The app supports operating systems: iOS 7+ or Android 4+.

In the event of an OS update, there may be a delay between the update of the OS and a related software update during which your OS may or may not be supported until a new version is released. Your specific mobile phone or problems in your network may prevent the system from working.

The TOSHIBA RAC-PD1414CWRU Smart AC only supports WPA-PSK/WPA2-PSK (recommended) encryption.

Devices required to use the TOSHIBA RAC-PD1414CWRU Smart AC are:

1. A smartphone with a compatible iOS or Android system.

2. A wireless router (a 2.4GHz network is required to connect).

3. The TOSHIBA RAC-PD1414CWRU Smart Air Conditioner.

You can scan the QR code in the manual to download the app.

Alternatively, you can go to Google Play or App Store and search for Toshiba NA AC.

Make sure your smartphone is connected to your wireless router and your wireless router has a working 2.4GHz internet connection. It is recommended to activate your account immediately to be able to recover your password by email.

To create an account:

1. Press “Sign Up”.

2. Enter your email address and password.

3. Press “Registration”.

If you forget your password, press “Forgot password?” on the main menu and enter your email address. Then press “Reset Password”.

Make sure your smartphone is able to connect to the wireless network which will be used. Make sure also that the device is not connecting to other networks in range.