TOPPING E30 (01) PDF MANUAL

TOPPING E30 (01) PDF SUMMARY:

What is included in the contents list?

The contents list includes:

• E30 X 1
• DC cable X 1
• USB cable X 1
• User’s manual X 1
• Warranty card x1
• Remote control X 1

(You can download the drivers on http://www.tpdz.net/.)

---

What are the attributes of the product?

• Measured 10.0cm x 12.5cm x 3.2cm
• Weight 265g
• Power input DC5V/1A
• Colour Black/Silver/Red/Blue/Gray
• Signal input USS/OPT/COAX
• Line Out output RCA

---

What are the functions of the front panel?

The front panel includes:

• LED screen
• Remote control receiver
• Multifunction touch button

---

What are the functions of the rear panel?

The rear panel includes:

• R channel of RCA output
• L channel of RCA output
• COAX input
• OPT input
• USB input
• Power input

---

What is the display screen?

• Volume indication (in pre-amplifier mode)
• PCM/DSD format indication

---

What are the functions of the remote control?

• Standby
• Volume up
• Switch to previous input
• Volume down
• Invalid button
• Filter setting
• Auto power on & off
• Mute
• Invalid button
• Switch to next input
• Invalid button
• Invalid button
• Brightness

---

What are the supported specifications?

• USB IN: 44.1 kHz-768kHz/16bit-32bit, DSD64-DSD512 (Native) ,DSD64-DSD256 (DoP)
• OPT/COAX IN: 44.1 kHz-192kHz/16bit-24bit

---

What are the specifications?

• Output Voltage 2Vrms@0dBFS
• THD+N <0.0003% @1 kHz A-weighting
• Noise <2uVrms @A-weighting
• Crosstalk -130dB@1kHz
• SNR >121dB@1kHz
• Dynamic Range 119dB@1kHz
• Channel Balance <0.3 dB

---

How to power on and off/standby operation?

• Power on: When connects to power supply, E30 goes into the standby state, the screen displays a bright dot.
• Standby setting: When it is working, long press the multifunction touch button on the front panel to enter standby state, short press to exit standby state when it is in standby. Or you can directly press the standby button by remote control to enter or exit standby state.

---

What is the note about the automatic standby function?

When the automatic standby function is on, if the current input is not connected or the input signal is invalid in 1 minute, it will automatically enter the standby state. Once a valid signal is detected on any input, it can automatically resume normal working status.

---

How to set the volume?

• The enter and exit of mute state: Press the mute button on the remote control to set mute, re-press the mute button, or adjust the volume to exit mute state.
• Volume adjusting: Press the volume up and down buttons on the remote to adjust the volume of the E30.

---

What is the note about the volume setting?

Volume is fixed to 0dB in DAC mode, and volume adjusting is invalid in this mode.

---

How to switch the input?

You can switch the input by pressing the multifunction touch button on the front panel or press the Switch to previous input button and the Switch to next input button on the remote control to switch the input in cycle.

---

What happens when the current input is not connected successfully?

“Err” will be displayed when the current input is not connected successfully.

---

How to set the output mode?

In the standby state, long press the multifunction touch button for 3 seconds to display the current output mode. Hold pressing, it will switch to another output mode after 1 second. The pre-amplifier mode displays “Pre” and the DAC mode displays “DAC”. When you choose the desired mode, let go and the E30 will automatically save the settings and return to standby.

---

How to set the PCM Filter?

• F-1 SHARP _ROLL_OFF _FILETER
• F-2 SLOW_ROLL_OFF _FILTER
• F-3 SHORT _DELAY _SHARP _ROLL_OFF _FILTER(Default)
• F-4 SHORT _DELAY _SLOW_ROLL_OFF _FILTER
• F-5 SUPER_SLOW_ROLL_OFF _FILTER
• F-6 LOW_DISPERSION_SHORT _DELAY _FILTER

---

How to set the DSD Filter?

• F.-1 39kHz (Default)
• F.-2 76kHz

---

How to set the screen brightness?

• L-1 Low
• L-2 Mid (Default)
• L-3 High

---

How to set the auto power on & off?

• A-O On (Default)
• A-C Off

---

What are the tips?

1. Other settings can be directly set by pressing the corresponding buttons on the remote control.
2. In the USB input state, press the mute button on the remote control first, then press the standby button. After that, the screen will light up, you can restore the factory settings.