TOPDON V1500 (01) PDF Document

For your safety, the safety of others, and to avoid any damage to the TOPDON V1500 and your vehicle, carefully read and ensure you fully understand all safety instructions before operating.

• ONLY use the battery clamps that come with this product.

• DO NOT use this product if the cable or the jump starter shows any signs of damage.

• DO NOT put the product under direct sunlight or in high temperature areas.

• The product contains a Lithium-Ion Battery. Please DISPOSE OF it under local regulations at the end of its life.

• Regularly check the battery level of the product and ENSURE that it is above 50%.

• V1500 Jump Starter

• Battery Clamps

• USB Cable

• User Manual

• Carrying Bag

1. Power Button: Press the power button to power ON. Press and hold the power button to turn on the LED light, then press the button again to toggle the light between Flashlight, SOS, Strobe, and OFF.

2. Battery Level Indicators: Indicate the charge level of the internal battery of the jump starter. (The four indicators will flash for around 10 seconds when an over-temperature is detected.) Note: Only jump-start vehicles when the battery level of the jump starter is above 50%.

3. Jump-Start Socket: The connection point for the battery clamps.

4. Temperature Detector: Used to detect over-temperatures in the jump starter.

5. USB Type-A Output: (5V3A) For charging electronic devices.

6. USB Type-C Input/Output: (PD18W) For charging the jump starter or charging other devices.

7. DC Output: (Max 16.8V/10A) For powering 12V DC devices.

8. LED Light: Provides illumination with multiple modes.

1. Tool Ready Indicator: Lights up solid green when the jump starter is ready for use.

2. Error Indicator: Lights up solid red when a reverse polarity, short circuit, over temperature, or improper connection is detected. The internal buzzer will also beep. Note: If the jump starter is properly connected, but neither the Tool Ready nor the Error indicator is illuminated, it may be because the vehicle’s battery voltage is less than 3V. Try jump-starting your vehicle with the BOOST mode.

3. BOOST Button: Press to enable the BOOST mode (forced output mode). The Tool Ready indicator will light up green. Start your vehicle within 30 seconds. The BOOST mode automatically turns off, and the green Tool Ready indicator goes out if the vehicle is not started within 30 seconds or successfully cranked. Note: Under the BOOST mode, all safety protections will be temporarily disabled. Use this mode with caution and only when the traditional battery jump option has been tried already.

4. Positive Clamp (Red)

5. Negative Clamp (Black)

The TOPDON V1500 jump starter comes partially charged and needs to be fully charged prior to use. Please charge the jump starter through the USB Type-C Input port once you receive it.

IMPORTANT: Make sure you have turned off all of the power loads of the vehicle, including headlights, radio, air conditioners, etc., before attempting to jump-start the vehicle. The jump-starting function is only applicable to 12V lead-acid battery vehicles.

Step 1: Plug the blue end of the battery clamps into the Jump Start Socket on the TOPDON V1500.

Step 2: Connect the battery clamps to the vehicle battery. Connect the Red clamp to the Positive Polarity (+) terminal, and the Black clamp to the Negative Polarity (-) terminal. The green illumination of the Tool Ready indicator shows that the jump starter is ready for jump-starting. Just by connecting the clamps to the terminals correctly, the V1500 delivers a jump to the vehicle battery.

Step 3: Try starting the vehicle. If it fails, disconnect the battery clamps from the vehicle’s battery and wait for 20 seconds, then reconnect and try again. It’s recommended not to attempt more than 3 consecutive jump starts within 2 minutes.

Step 4: After successfully jumping the vehicle, remove the clamps from the vehicle battery and separate the battery clamps from the jump pack. Your jump starter will automatically power off in around 10 seconds.

To convert the TOPDON V1500 into a power bank, press the Power Button to turn on the jump starter. Then you can use it to charge electronic devices like phones and tablets through the USB Type-A Output port or supply power to 12V electronic devices via the DC Output port (Max 16.8V/10A).

Battery Capacity	3.7V, 10,000mAh, 37Wh
USB Type-A Output	5V=3A
DC Output (5.5mm*2.1mm)	Max 16.8V=10A
USB Type-C Input/Output	PD18W, 5V=3A, 9V=2A
Peak Current	1500A
Working Temperature	-10°C to 40°C (14°F to 104°F)
Storage Temperature	-20°C to 75°C (-4°F to 167°F)

The time it takes to fully recharge a TOPDON V1500 varies depending on the charger used. For example, a 5V/2A charger takes approximately 4.5 hours.

It’s possible that the TOPDON V1500 jump starter is overheating as you have jump-started too frequently in a short period of time. Please try again in 20 minutes.

The DC output voltage can reach up to 16.8V as it is consistent with that of the jump starter (ranges from 13.2 to 16.8V, and increases as the battery level rises). However, most 12V devices can withstand up to 18V, so no damage should occur.