TOASTMASTER 2238CAN (01) PDF Document

When using electrical appliances like the TOASTMASTER 2238CAN, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following:

• Read all instructions before using the appliance.

• Do not immerse the cord, plug, or appliance in water or other liquid. See instructions for cleaning.

• Close supervision is necessary when any appliance is used near children.

• This appliance is not for use by children.

• Avoid contacting moving parts.

• Unplug from the outlet when not in use, before putting on or taking off parts, and before cleaning.

• Do not operate any damaged appliance. Do not operate with a damaged cord or plug, or after the appliance malfunctions, or has been dropped or damaged in any manner. Return the appliance to the nearest authorized service center for examination, repair, or electrical or mechanical adjustment.

• Use attachments only if recommended by Toastmaster Inc.

• Do not place on or near a hot gas or electric burner or in a heated oven.

• Do not use outdoors or while standing in a damp area.

• Do not let the cord hang over the edge of a table or counter, or touch hot surfaces.

• Do not open pressurized (aerosol-type) cans or cans of flammable liquid, such as lighter fluids.

• Use the appliance only as indicated in these instructions.

THIS PRODUCT IS FOR HOUSEHOLD USE ONLY.

A short power supply cord is provided to reduce the risk of personal injury resulting from becoming entangled in or tripping over a longer cord. Extension cords are available from local hardware stores and may be used if care is exercised in their use. If an extension cord is required, special care and caution are necessary. Also, the cord must be: (1) marked with an electrical rating of 125 V and at least 10 A, 1250 W, and (2) the cord must be arranged so that it will not drape over the countertop or tabletop where it can be pulled on by children or tripped over accidentally.

The TOASTMASTER 2238CAN has a polarized plug, where one blade is wider than the other. As a safety feature to reduce the risk of electrical shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.

1. Remove all packaging materials before using.

2. Place the can opener on a level surface and plug it into a 120V~60 Hz electrical outlet.

3. Hold the can approximately level.

4. Raising the lever, place the can under the guide bar and against the geared wheel.

5. Press down on the lever to pierce the lid of the can. This also starts the cutting action. Let go of the lever and the can will stop automatically when opened.

6. Grasp the can, then raise the lever up from the can.

7. Slide the lid away from the magnet. Use caution to avoid injury from the sharp edge of the lid.

Yes, to open extra tall cans, place the can opener at the edge of the counter before wedging the can in position for opening.

Turn the unit sideways so that the knife and scissors sharpener is to your right.

1. Press down and hold the lever.

2. Place the blade lightly in either the left or right groove of the knife sharpener. Draw the knife slowly toward you with a slow, even motion.

3. Place the blade in the other knife sharpener groove and repeat 4 or 5 times, alternating from one groove to the other until the desired sharpness is achieved. Release the lever.

4. The larger groove at the bottom is designed especially for scissors. Press down and hold the lever. Place one blade of the scissors in the groove, and then draw it toward you slowly and evenly. Repeat with the other blade.

5. Wash and dry blades after sharpening.

• Be sure that blades are clean and free of grease. Greasy or wet blades may coat the grinding wheel and the blade will not sharpen satisfactorily.

• Do not attempt to sharpen hollow ground or serrated blades.

• If the knife has a curved tip, raise the knife handle slightly at the end of each sharpening.

• Uneven sharpening may occur if you force the knife blade against the Grinding Wheel.

Do not use the can opener, knife, or scissors sharpener for more than 5 minutes at a time. Allow it to cool for at least 15 minutes after sharpening blades before using. This will prevent motor burnout due to overheating.

First, unplug the unit from the electrical outlet.

1. To remove the lever, hold the can opener facing you. Lift the lever upward to the highest position and push the lever to the right.

2. Wash the lever in warm, soapy water and wipe the outside surfaces of the unit with a damp cloth.

3. To replace the lever, hold the can opener facing you with the lever in the lifted position and slide the pivot into the pivot hole. Push the lever to the left until it snaps into place. Lower the lever back onto the top of the can opener.

4. Store the cord in the cord storage area.

NOTE: The cutting blade is sharp; use caution.

Any servicing requiring disassembly other than the above cleaning must be performed by an authorized service center.