THRUSTMASTER TX (01) PDF Document

The THRUSTMASTER TX features the following components:

1. Racing wheel base

2. Racing wheel

3. 2 sequential gear shift levers (Up & Down)

4. Multidirectional D-Pad

5. Switch (3 positions)

6. MODE button + Red/Green indicator light

7. Xbox Guide button

8. White indicator light

9. Large threaded hole (for attachment system and tightening screw)

10. Attachment system

11. Metal fastening screw

12. Thrustmaster Quick Release

13. Mains supply connector (type A or B, varies from one country to another)

14. Racing wheel USB cable and connector

15. Gearbox connector (sold separately)

16. Pedal set connector

Your THRUSTMASTER TX racing wheel’s power supply varies depending on the country where you purchased it. The mains supply can be:

Internal, with a 220-240V mains power supply cable:

This version has a power supply unit located directly inside the racing wheel’s base with a type A connector. It is compatible only with a 220-240V electrical supply. WARNING: Never connect the 220-240V cable to a 100-130V power outlet. Never connect this cable to a mains power adapter.

Internal, with a 100-125V mains power supply cable:

This version has a power supply unit located directly inside the racing wheel’s base with a type A connector. It is compatible only with a 100-125V electrical supply. WARNING: Never connect the 100-125V cable to a 220-240V power outlet. Never connect this cable to a mains power adapter.

External, with a mains power supply cable:

This version has an external power supply unit located on the racing wheel’s base with a type B connector. It is compatible with all supply voltages, 110-240V.

IMPORTANT: If you do not know which voltage is supplied in the area in which you are using your racing wheel, please refer to your local electricity supplier.

Before using the THRUSTMASTER TX, please read the following warnings carefully:

Warning – Electric shock

* Store the product in a dry location and do not expose it to dust or sunlight.

* Respect the connection direction.

* Do not twist or pull the connectors and cables.

* Do not spill any liquid on the product or its connectors.

* Do not short-circuit the product.

* Never dismantle the product; do not throw it onto a fire and do not expose it to high temperatures.

* Do not use a power supply cable other than the one provided with your racing wheel.

* Do not use the mains power supply cable if the cable or the connectors are damaged, split or broken.

* Make sure that the mains power cable is properly inserted into the power outlet and the connector located on the rear face of the racing wheel’s base.

* Do not open. No user replaceable parts inside. Refer servicing to manufacturer, specified agency or qualified technician.

* Only use attachments/accessories specified by the manufacturer.

* If the steering wheel is operating unusually (if it is emitting any abnormal sounds, heat or odors), stop using it immediately, disconnect the power cable from the socket and disconnect the other cables.

* If you are not going to be using the steering wheel for an extended period, disconnect the mains adaptor from the wall socket.

Air vents

Make sure that you do not block any of the air vents on the steering wheel base. For optimum ventilation, respect the points below:

* Position the base at least 10 cm away from any wall surfaces.

* Do not place the base in any tight spaces.

* Do not cover the base.

* Do not let any dust build up on the air vents.

Warning – Injuries due to force feedback and repeated movements

Playing with a force-feedback steering wheel may cause muscle or joint pain. To avoid any problems:

* Avoid lengthy gaming periods.

* Take 10 to 15 minute breaks after each hour of play.

* If you feel any fatigue or pain in your hands, wrists, arms, feet or legs, stop playing and rest for a few hours before you start playing again.

* If the symptoms or pain indicated above persist when you start playing again, stop playing and consult your doctor.

* Keep out of children’s reach.

* During games, always leave both hands correctly positioned on the steering wheel without completely letting go.

* During gameplay, never place your hands or your fingers under the pedals or anywhere near the pedal set.

* During calibration and gameplay, never place your hand or your arm through the openings in the racing wheel.

* Check the steering wheel base is carefully clamped as per manual’s instructions.

Heavy Product Warnings

* The THRUSTMASTER TX is a heavy product (7 kg) and should be handled only by users 16 years of age or older.

* Be careful not to drop the product on yourself or on anyone else!

Pedal set pinch hazard warnings

* Keep the pedal set out of children’s reach.

* When playing, never place your fingers on or anywhere near the sides, rear base, or front base of the pedals.

* Store the pedal set in a safe place, and keep it out of children’s reach when not playing.

1. Align the connector locations using the arrows: the arrow on the Base (1) connector should point upwards, and the arrow on the Racing wheel (2) connector should also point upwards.

2. Once the connectors are correctly positioned, rotate the Thrustmaster Quick Release (12) device’s ring counterclockwise, while holding the racing wheel (2) in position.

3. Tighten the ring as much as you can by holding the ring in position and rotating the racing wheel clockwise.

4. After installing the wheel, rotate it 180° (the logo should be upside down when facing the wheel) to access the small attachment screw on the Thrustmaster Quick Release (12) device.

5. Use a large cross-slot screwdriver to tighten the small attachment screw clockwise. Do not use excessive force; stop turning the screw as soon as you feel some resistance.

1. Place the racing wheel on a table or any other horizontal, flat, and stable surface.

2. Insert the fastening screw (11) into the attachment system (10).

3. Tighten the device by turning the screw counterclockwise, so that it feeds into the large threaded hole (9) located beneath the racing wheel, until the device is perfectly stable.

WARNING: Never tighten the screw alone without the attachment system, as this could damage the racing wheel.

1. Place the racing wheel’s base on the cockpit shelf.

2. Drive two M6 screws (not included) through the cockpit shelf and feed them into the two small threaded holes located beneath the racing wheel.

Important: The length of the M6 screws should not exceed the thickness of the shelf + 12 mm; longer screws could cause damage to internal components located in the racing wheel’s base.

3. If required, tighten the standard attachment system by inserting the fastening screw in the large threaded hole.

1. Connect the pedal set to the connector (16) located at the back of the racing wheel’s base.

2. Connect the power supply cable to the connector (13) located at the back of the racing wheel’s base.

3. Connect the power supply cable to a mains outlet with proper voltage specifications.

4. Connect the racing wheel’s USB connector (14) to one of the console’s USB ports.

You are now ready to race!

Automatic Racing Wheel Calibration:

The racing wheel automatically self-calibrates when you connect it to the mains and its USB connector to the console. During this phase, the racing wheel will rotate quickly left and right, covering a 900-degree angle, before stopping at the center.

WARNING: Never touch the racing wheel during the self-calibration phase! This could cause incorrect calibration and/or personal injuries.

Automatic Pedal Set Calibration:

Always connect the pedal set to the base before connecting the racing wheel to the console. Never connect or disconnect the pedal set from the base when it is connected to the console or during gameplay. Once the wheel’s calibration is done and the game has been launched, the pedals automatically calibrate after a few presses.

WARNING: Never press the pedals during the wheel’s self-calibration phase or while a game is loading, as this could cause incorrect calibration.

If your racing wheel and pedal set do not operate correctly, or if calibration seems incorrect, follow these steps:

1. Turn off your console.

2. Disconnect your racing wheel entirely.

3. Reconnect all cables, including the mains power supply cable and the pedal set cable.

4. Restart your console and your game.

For safety reasons, the THRUSTMASTER TX racing wheel’s base features an internal temperature sensor. If the device’s temperature becomes too high, the racing wheel can shut down suddenly. In this event:

– Unplug the mains power supply cable and the device’s USB connector.

– Wait for the racing wheel’s base to cool down entirely.

– Then, reconnect the device.

You can electronically swap the accelerator and clutch pedals on your THRUSTMASTER TX. To do so, simply press the MODE button (6) for 2 seconds. The racing wheel’s internal memory stores whether the pedals have been swapped. The color of the MODE indicator light (6) will change to show the current setting.

ATTENTION: To avoid any calibration problems, be sure to always disconnect your wheel’s USB cable from the console or PC before making any adjustments to your pedal set.

Adjusting the HEIGHT of the accelerator pedal:

1. Using the included 2.5 mm Allen key (4), unscrew the two screws holding the metal head (8) and its support (7) in place.

2. Select your preferred height position, then replace and re-tighten the screws so that the metal head (8) and its support (7) are held firmly in place.

Adjusting the SPACING of the three pedals:

1. Using the included 2.5 mm Allen key (4), unscrew the two screws holding the metal head (8) and its support (7) in place.

2. Select your preferred position (to the left, centered, or to the right), then replace and re-tighten the screws so that the metal head (8) and its support (7) are held firmly in place.

There are three possible spacing positions for each pedal (accelerator, brake, and clutch).

Adjusting the INCLINATION of the pedals:

1. Using the included 2.5 mm Allen key (4), unscrew the two screws holding the metal head (8) and its support (7) in place.

2. Turn the plastic head support (7) 180°, then replace and re-tighten the screws so that the metal head (8) and its support (7) are held firmly in place.

There are two possible inclination positions for each pedal (accelerator, brake, and clutch).

This modification is not essential and is not installed by default. It allows you to experience a different feeling and resistance when braking. Installation is optional and depends on your preference.

1. Screw the conical stop (2) onto its metal support (1).

2. Screw the position adjustment nut (5) onto the bottom of the conical stop’s screw thread.

3. Position the unit at the back of the brake pedal’s arm.

4. Using the included 2.5 mm Allen key (4), attach the unit using the attachment screw (3) and the small central screw thread located on the underside of the pedal set.

By slightly unscrewing the nut (5), you can further strengthen the resistance of the brake pedal by moving the conical stop (2) closer to the back of the pedal’s arm. The closer the conical stop is positioned to the back of the pedal’s arm, the greater the strength of resistance will be. If necessary, use a 14 mm wrench or pliers to re-tighten the nut and maintain the selected position.

Note: When the conical stop is very close to the back of the brake pedal’s arm, you may experience difficulties in reaching the maximum calibration value. Should that be the case:

* Slowly, press very hard on the brake pedal so as to reach the maximum value (if necessary, stand very briefly on the pedal – just for a second), then release the pressure; or else

* Move the conical stop a bit farther away from the back of the brake pedal’s arm.