THERMO SCIENTIFIC FD1530M-33 (01) PDF Document

Free English THERMO SCIENTIFIC FD1530M-33 (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.

CLICK HERE TO DOWNLOAD THERMO SCIENTIFIC FD1530M-33 (01) PDF DOCUMENT

If this is not the document you want for this product, click here to see if we have any other documents for this product.

How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.

What are the general specifications for the THERMO SCIENTIFIC FD1530M-33?

The THERMO SCIENTIFIC FD1530M-33 has the following general specifications:

MODEL NUMBER	FD1540M-33 FD1530M-33
CHAMBER WIDTH	4 (10 CM)
CHAMBER HEIGHT	3-3/4 (9.5 CM)
CHAMBER DEPTH	9 (22.9 CM)
OVERALL WIDTH	11 (28 CM)
OVERALL HEIGHT	16-1/2 (42 CM)
OVERALL DEPTH	18 (46 CM)
WEIGHT LBS. (KG)	42 LBS (19 KG)
ELECTRICAL RATINGS VOLTS	220-240
ELECTRICAL RATINGS AMPS	6.5
ELECTRICAL RATINGS WATTS	1560
ELECTRICAL RATINGS FREQ.	50/60
ELECTRICAL RATINGS PHASE	1
OPERATING TEMP RANGE CONT.	100°C-1066°C
OPERATING TEMP RANGE INTERMITTENT	1066°C-1200°C

What are the environmental conditions for operating the THERMO SCIENTIFIC FD1530M-33?

The operating environmental conditions are: 17°C – 27°C; 20% to 80% relative humidity, non-condensing. Installation Category II (over-voltage) in accordance with IEC 664. Pollution Degree 2 in accordance with IEC 664. Altitude limit: 2,000 meters. Storage conditions are: -25°C to 65°C; 20% to 80% relative humidity.

What should be done when unpacking the THERMO SCIENTIFIC FD1530M-33?

Visually check for any physical damage to the shipping container. Inspect the equipment surfaces that are adjacent to any damaged area. Unpack furnace from box. The owner’s manual and door handle are included in the box. After unpacking the furnace, attach the door handle and remove packing material from inside furnace chamber. The furnace is supplied with one hearth plate. The 120V models are not supplied with a power cord because current requirements are too great to be handled by ordinary power cords and standard wall supply.

POSSIBLE CAUSES	CORRECTIVE ACTION
The furnace is not connected to power supply.	Reconnect furnace to power supply.
Incorrect power source.	Connect to correct power source.
ON and OFF power switch defective.	Replace power switch.
Defective cycle light.	Replace cycle light.
Door switch malfunction.	Realign or replace furnace door safety switch.

POSSIBLE CAUSES

CORRECTIVE ACTION

The furnace is not connected to power supply.

Reconnect furnace to power supply.

Incorrect power source.

Connect to correct power source.

ON and OFF power switch defective.

Replace power switch.

Defective cycle light.

Replace cycle light.

Door switch malfunction.

Realign or replace furnace door safety switch.

POSSIBLE CAUSES	CORRECTIVE ACTION
No power.	Check power source and fuses or breakers.
Defective electrical hookup.	Repair electrical hookup.
Thermocouple has oxidized and opened the circuit.	Replace thermocouple.
Controller malfunction.	Replace controller.
Heating elements burned out.	Replace defective elements.
Solid state relay defective.	Replace solid state relay.
Door switch malfunction.	Re-align or replace door switch.
Defective OTP relay.	Replace relay.
Defective solid state relay.	Replace relay.

POSSIBLE CAUSES

CORRECTIVE ACTION

No power.

Check power source and fuses or breakers.

Defective electrical hookup.

Repair electrical hookup.

Thermocouple has oxidized and opened the circuit.

Replace thermocouple.

Controller malfunction.

Replace controller.

Heating elements burned out.

Replace defective elements.

Solid state relay defective.

Replace solid state relay.

Door switch malfunction.

Re-align or replace door switch.

Defective OTP relay.

Replace relay.

Defective solid state relay.

Replace relay.

POSSIBLE CAUSES	CORRECTIVE ACTION
Door switch not functioning	Realign or replace door safety switch.

POSSIBLE CAUSES

CORRECTIVE ACTION

Door switch not functioning

Realign or replace door safety switch.

POSSIBLE CAUSES	CORRECTIVE ACTION
Alarm output device malfunction.	Replace controller.
OTP relay malfunction.	Replace relay.
Element shorted to ground.	Replace faulty element.

POSSIBLE CAUSES

CORRECTIVE ACTION

Alarm output device malfunction.

Replace controller.

OTP relay malfunction.

Replace relay.

Element shorted to ground.

Replace faulty element.

POSSIBLE CAUSES	CORRECTIVE ACTION
Low line voltage.	Install line of sufficient size and proper voltage. (Isolate furnace from other electrical loads.)
Wrong heating element.	Install proper element.
Heating element burned out.	Replace element.
Heavy load in chamber.	Lighten load in chamber to allow heat to circulate.

POSSIBLE CAUSES

CORRECTIVE ACTION

Low line voltage.

Install line of sufficient size and proper voltage. (Isolate furnace from other electrical loads.)

Wrong heating element.

Install proper element.

Heating element burned out.

Replace element.

Heavy load in chamber.

Lighten load in chamber to allow heat to circulate.

POSSIBLE CAUSES	CORRECTIVE ACTION
Overheating furnace.	Keep furnace under maximum temperature. Closer supervision of control setting.
Heating harmful materials.	Enclose material in container. Clean up spills in and on chamber. Ventilate chamber by leaving top vent slightly open when heating known harmful reagents.
Contamination present from previous burnout.	Replace insulation material.

POSSIBLE CAUSES

CORRECTIVE ACTION

Overheating furnace.

Keep furnace under maximum temperature. Closer supervision of control setting.

Heating harmful materials.

Enclose material in container. Clean up spills in and on chamber. Ventilate chamber by leaving top vent slightly open when heating known harmful reagents.

Contamination present from previous burnout.

Replace insulation material.

POSSIBLE CAUSES	CORRECTIVE ACTION
Oxidized or contaminated thermocouple.	Replace thermocouple.
Poor thermocouple connection.	Tighten connections.
Improper loading procedures.	Use proper loading procedures.
Poor ventilation of control.	Clear area around furnace control.
Thermocouple connections reversed.	Reconnect thermocouple correctly.

POSSIBLE CAUSES

CORRECTIVE ACTION

Oxidized or contaminated thermocouple.

Replace thermocouple.

Poor thermocouple connection.

Tighten connections.

Improper loading procedures.

Use proper loading procedures.

Poor ventilation of control.

Clear area around furnace control.

Thermocouple connections reversed.

Reconnect thermocouple correctly.

What are the general specifications for the THERMO SCIENTIFIC FD1530M-33?

What are the environmental conditions for operating the THERMO SCIENTIFIC FD1530M-33?

What should be done when unpacking the THERMO SCIENTIFIC FD1530M-33?

What precautions should be taken regarding ambient temperature during installation of the THERMO SCIENTIFIC FD1530M-33?

What clearance space is required around the THERMO SCIENTIFIC FD1530M-33 during installation?

How should the power switch on the THERMO SCIENTIFIC FD1530M-33 be set before connecting to electrical supply?

How can the door safety switches on the THERMO SCIENTIFIC FD1530M-33 be checked?

What is the function of the Power Switch when turned ON for the THERMO SCIENTIFIC FD1530M-33?

What does the amber cycle light indicate on the THERMO SCIENTIFIC FD1530M-33?

What is displayed on the Digital Readout of the THERMO SCIENTIFIC FD1530M-33?

How is the setpoint changed on the Eurotherm 3216 Controller in the THERMO SCIENTIFIC FD1530M-33?

How are the display units viewed on the Eurotherm 3216 Controller in the THERMO SCIENTIFIC FD1530M-33?

What are the available Controller Parameters in the Home display for the Eurotherm 3216 Controller in the THERMO SCIENTIFIC FD1530M-33?

What are the Pid List parameters for the Eurotherm 3216 Controller in the THERMO SCIENTIFIC FD1530M-33?

What alarm messages are displayed on the Eurotherm 3216 Controller in the THERMO SCIENTIFIC FD1530M-33 if an alarm condition is detected?

How does Sensor Break Protection work on the Eurotherm 3216 Controller in the THERMO SCIENTIFIC FD1530M-33?

How can Over-Temperature Protection (OTP) be adjusted on the Eurotherm 3216 Controller in the THERMO SCIENTIFIC FD1530M-33?

How can the Single Ramp & Dwell features be configured on the Eurotherm 3216 Controller in the THERMO SCIENTIFIC FD1530M-33?

What are the steps for SetPoint Rate Limit Setup for the Single Ramp & Dwell Controller in the THERMO SCIENTIFIC FD1530M-33?

What are the steps for Running the Program on the Single Ramp & Dwell Controller in the THERMO SCIENTIFIC FD1530M-33?

How is the program Held on the Single Ramp & Dwell Controller in the THERMO SCIENTIFIC FD1530M-33?

How is the program Stopped on the Single Ramp & Dwell Controller in the THERMO SCIENTIFIC FD1530M-33?

How is the Flashing End Cleared on the Single Ramp & Dwell Controller in the THERMO SCIENTIFIC FD1530M-33?

How can a Running Program be Verified on the Single Ramp & Dwell Controller in the THERMO SCIENTIFIC FD1530M-33?

How is the setpoint changed on the 8 Segment Programmable Model w/OTP for the THERMO SCIENTIFIC FD1540M-33?

How are the Display Units viewed on the 8 Segment Programmable Model w/OTP for the THERMO SCIENTIFIC FD1540M-33?

How is the % Output Power viewed on the 8 Segment Programmable Model w/OTP for the THERMO SCIENTIFIC FD1540M-33?

What are the Buttons and Indicators for the 8 Segment Programmable Model w/OTP?

What are the Controller Parameters listed under Home Display for the 8 Segment Programmable Model w/OTP?

What are the Controller Parameters listed under run LiSt (Program Run List) for the 8 Segment Programmable Model w/OTP?

What are the Controller Parameters listed under ProG LiSt (Program Edit List) for the 8 Segment Programmable Model w/OTP?

What are the Controller Parameters listed under AL LiSt (Alarm List) for the 8 Segment Programmable Model w/OTP?

What are the Controller Parameters listed under Atun LiSt (Autotune List) for the 8 Segment Programmable Model w/OTP?

What are the Controller Parameters listed under Pid LiSt for the 8 Segment Programmable Model w/OTP?

What alarm messages are displayed on the 8 Segment Programmable Model w/OTP if an alarm condition is detected?

How does Sensor Break Protection work on the 8 Segment Programmable Model w/OTP?

How can Over-Temperature Protection (OTP) be adjusted on the 8 Segment Programmable Model w/OTP?

How can the 8 Segment Programmable Model w/OTP be operated as a Single Setpoint Controller?

How is Gain Scheduling (G.SP) set for the 8 Segment Programmable Model w/OTP?

What are the steps to tune the 8 Segment Programmable Model w/OTP using Autotuning?

What are the steps to tune the 8 Segment Programmable Model w/OTP using Adaptive Tuning?

What is the recommendation for Furnace Loading for the 8 Segment Programmable Model w/OTP?

What should be done before using any cleaning or decontamination method on the THERMO SCIENTIFIC FD1530M-33?

What should be done before cleaning the THERMO SCIENTIFIC FD1530M-33?

What is advised regarding opening the door of the THERMO SCIENTIFIC FD1530M-33 for an extended period of time?

What contaminants should be avoided when heating in the THERMO SCIENTIFIC FD1530M-33?

What maintenance should be performed periodically for the thermocouple in the THERMO SCIENTIFIC FD1530M-33 during normal use?

What is the suggested procedure for cleaning the exterior case of the THERMO SCIENTIFIC FD1530M-33?

What are the possible causes and corrective actions if the cycle light on the THERMO SCIENTIFIC FD1530M-33 does not illuminate?

What are the possible causes and corrective actions if the THERMO SCIENTIFIC FD1530M-33 furnace does not heat?

What are the possible causes and corrective actions if the door switch on the THERMO SCIENTIFIC FD1530M-33 does not cut power to heating elements?

What are the possible causes and corrective actions if the controller over-temp. does not cut power to the furnace chamber of the THERMO SCIENTIFIC FD1530M-33?

What are the possible causes and corrective actions for slow heatup on the THERMO SCIENTIFIC FD1530M-33?

What are the possible causes and corrective actions for repeated element burnout on the THERMO SCIENTIFIC FD1530M-33?

What are the possible causes and corrective actions for inaccurate temperature readout on the THERMO SCIENTIFIC FD1530M-33?

What are the steps to replace a heating element on the THERMO SCIENTIFIC FD1530M-33?

What are the steps to replace the Platinel II Thermocouple on the THERMO SCIENTIFIC FD1530M-33?

What are the steps to replace the Door Switch (Micro-Switch) on the THERMO SCIENTIFIC FD1530M-33?

What are the steps to Realign Door Switches on the THERMO SCIENTIFIC FD1530M-33?

What is the procedure to Replace the Controller on the THERMO SCIENTIFIC FD1530M-33?

Visitors also searched:

Leave comments, questions, reviews, tips, tricks, hacks or page errors below. Account not required.Cancel reply

Discover more from Manual-Hub.com