TESCO CR106R (01) PDF MANUAL

TESCO CR106R (01) PDF SUMMARY:

How do I clean the unit?

UNPLUG the unit from the mains power. The surface of the unit can be cleaned with a barely damp cloth and then dried carefully. Never use abrasives, abrasive cloths or chemical solvents.

What should I do before connecting the power?

Before connecting the power, check that the mains voltage on the rating plate under the radio is the same as the voltage in your area. Place the unit on a stable surface away from heat and damp. Unwrap the FM antenna cable and extend it fully. Uncoil the mains cable fully. Plug the mains plug into the wall socket and switch the mains power on. Your unit is now ready for use.

How do I set the clock?

The Clock is a 24 hour clock; e.g. 6 pm is entered as 18:00 hours.

• Hold the TIME SET/M+ button down until the display flashes.
• Release the TIME SET/M+ button.
• Press the HOUR/UP button repeatedly until the hour is set correctly.
• Press the MIN/DOWN button repeatedly until the minutes are set correctly.
• Press the TIME SET /M+ button to save the time setting.
• The time is now set.

How do I operate the radio?

To turn the radio on, press the OFF/FM/ AM button repeatedly to select FM or AM operation. Press the HOUR/UP or MIN/DOWN button to tune up or down the band. Move the FM antenna to improve FM signal quality. To improve AM reception, move the radio around or rotate it. To turn the radio off, press and hold the OFF /FM/ AM button until the radio switches off and the clock is displayed.

How do I store a preset station?

Your radio can store up to 20 of your favourite stations as presets (10 FM, 10 AM) for quick recall. To store a preset station:

• Tune to the station you want to store as a preset.
• Press and hold the TIME/M+ button. ‘PO 1’ will flash on the display.
• Press the HOUR/UP or MIN/DOWN button to select the preset number you want to store.
• Press the TIME/M+ button to store the preset.

How do I tune to a preset station?

Press the TIME/M+ button repeatedly to step through the presets available.

How do I adjust the volume?

Press the AL2NOL + button to increase the volume level or press the AL 1NOL- button to decrease the volume.

How do I set the alarm time?

Example: set Alarm 1 or Alarm 2 to ring at 8:22 AM.

• Press and hold the AL 1/VOL- button to set Alarm 1 or the AL2/ VOL+ button to set Alarm 2. The alarm time will flash on the display.
• Release the button. Press the HOUR/UP button repeatedly until the alarm hour is set correctly (8 in the example). Press the MIN/DOWN button repeatedly until the alarm minutes are set correctly (22 in the example).
• The alarm time is now set.

How do I wake up to the radio or buzzer?

After setting the alarm time, press the AL 1/VOL- or AL2/VOL + button repeatedly to step through the Alarm wake up modes (Off/Radio/Buzzer) for Alarm 1 or Alarm 2. The Alarm 1 or 2 indicators will come on and indicate the wake-up mode. Switch the radio off. When the time comes the buzzer or radio will sound.

How do I switch the alarm off when it sounds?

Press the OFF/FM/AM button to switch the alarm OFF.

How do I use the snooze function?

When the alarm goes off:

• Press the SNOOZE/SLEEP button. The alarm will switch off temporarily. After 9 minutes the alarm will sound again.

How do I use the sleep function?

When the radio is playing you can programme the clock to switch off after a predetermined time.

• Set the radio to play.
• Press the SNOOZE/SLEEP button. The sleep time of 90 minutes appears.
• Press the SNOOZE/SLEEP button repeatedly to set the sleep time you want in the range 10- 90 minutes. After the preset time the radio will switch off.

If you have set the alarm, the radio will switch on again at the alarm time.