SWIT PL-E60D (01) PDF MANUAL

1. Do not disassemble the panel light or touch the interior with metal objects to prevent damaging the equipment.

2. Do not store the panel light in dusty or wet environment to avoid damage.

3. In order to ensure safety, please use the safety rope when hoisting the lamp.

4. Working temperature is between -10°C and 40°C.

1. Please clean the front LED panel with soft dry cloth. If using soft cloth with slight clean neutral detergent solution, please wipe again with a soft dry cloth.

2. Do not use wet cloth, anhydrous alcohol, gasoline, or a mixture of anhydrous alcohol and ether etc. to wipe the front LED panel.

The LCD display shows the following information (using an example of 5600K, 100% dimmer, battery power, DMX mode, address 008):

① Current communication control mode (e.g., DMX)

② Current communication control mode (e.g., interaction control mode if selected)

③ Brightness display (e.g., 100%)

④ Communication address (e.g., 008)

⑤ CT (Color Temperature) display (e.g., 5600K)

⑥ Power supply display (shows an icon for AC adaptor power supply)

⑦ Power supply display (shows an icon for battery power supply)

When powered by battery, the battery capacity will be displayed as follows:

Please confirm the type of honeycomb before use. The available types and sizes are:

1) Purchase of big honeycomb: The installation method is shown in Fig. 10.

2) Purchase of small honeycomb: The small honeycomb can be used simultaneously with the barndoor. After installing the barndoor (as shown in Fig. 11), fix the honeycomb by rotating the pressure plate (Fig. 12 ⑬), and then use the light normally.

The method to install the barn door is shown in Fig. 9 and Fig. 11.

Note: Put the low head screws upward during the installation.

Users can install the light on a tripod or stand. Adjust the desired beam angle by using the bracket knobs (Fig. 4 ⑤ / Fig. 5 ⑤) on both sides of the U-shape bracket.

The light provides two ways of power supply:

1. By V-mount or Gold mount battery attached to the battery plate (Fig. 6 ⑥ / Fig. 7 ⑥).

2. By 4-pin XLR AC-DC power connected to the DC11-36V IN socket (Fig. 6 ⑨ / Fig. 7 ⑨).

Turn on the light using the power switch (Fig. 6 ⑫ / Fig. 7 ⑫) and set the color temperature and brightness to your requirements.

(1) Connection:

Align the hump of the output male XLR plug (from the adaptor) to the gap of the DC socket (Fig. 6 ⑨ / Fig. 7 ⑨) on the light. Connect the XLR and DC socket. The adaptor will connect securely with the light when you hear a click sound.

(2) Disconnection:

Hold the hump/release mechanism on the female XLR plug (from the adaptor) and pull it out from the DC socket. The power adaptor and the light will be disconnected.

The light offers two adjustment modes: normal and quick. Switch between modes by pressing the dimmer knob (Fig. 6 ⑬ / Fig. 7 ⑬) or the color temperature (CT) dimming knob (Fig. 6 ⑦ / Fig. 7 ⑦).

3.1 Normal adjusting mode:

(1). Color temperature adjust: Rotate the CT dimming knob (Fig. 6 ⑦ / Fig. 7 ⑦). Range: 2700K-6500K, adjustment step: 50K.

(2). Dimmer adjust: Rotate the Dimmer knob (Fig. 6 ⑬ / Fig. 7 ⑬). Range: 0%-100%, adjustment step: 1%.

3.2 Quick adjusting mode:

(1). Color temperature adjust: Press the CT dimming knob (Fig. 6 ⑦ / Fig. 7 ⑦) to cycle through common color temperatures: 2700K, 3200K, 4500K, 5600K, and 6500K.

(2). Dimmer adjust: Press the Dimmer knob (Fig. 6 ⑬ / Fig. 7 ⑬) to adjust in larger steps. Range: 0%-100%, adjustment step: 10%.

1. Press and hold the dimmer knob (Fig. 6 ⑬ / Fig. 7 ⑬) for 2 seconds to enter the communication address setting interface.

2. The address setting range is 001 to 512.

3. The communication address digits on the LCD (Fig. 8 ④) will flash, indicating it’s selected.

4. Rotate the dimmer knob (Fig. 6 ⑬ / Fig. 7 ⑬) to set the desired address.

5. Press the dimmer knob (Fig. 6 ⑬ / Fig. 7 ⑬) to confirm the setting.

6. After finishing the setting, press the dimmer knob again or wait for about 5 seconds to exit the setting interface.

Connect the lights network using DMX cables via the DMX IN (Fig. 6 ⑧ / Fig. 7 ⑧) and DMX OUT (Fig. 6 ⑩ / Fig. 7 ⑩) ports.

Press and hold the color temperature (CT) adjusting knob (Fig. 6 ⑦ / Fig. 7 ⑦) for around 2 seconds to switch between communication control modes.

When the upper left corner of the LCD shows “DMX” (Fig. 8 ①), the light is in DMX communication mode.

In this mode, connect a DMX signal output device (controller) to the lights network and set the communication address (001-512) on each light.

Each light occupies 2 DMX control channels:

• The set DMX address (N) controls Brightness (0%-100%).
• The next address (N+1) controls Color Temperature (2700K-6500K).

For example:

When the upper left corner of the LCD shows “CH” (Fig. 8 ②), the light is in interaction control mode.

In this mode, set the target lights to the same communication address. All lights with the same address will work together.

Adjusting the brightness or color temperature on any light within the group will control all other lights set to the same address.

The master-slave relationship is not distinguished; any light can act as a controller for the group.

The USB socket (Fig. 6 ⑪ / Fig. 7 ⑪) is a reserved socket. Please use it according to the specified using environment for related products, and do not use it for other purposes to avoid damage.

The parameters of the recommended adaptor are below:

Note: The adaptor and LED PCB board can be changed.

There are two package options:

Package 1: Single light package

Package 2: Single light package (with barn door)

Optional items like DMX cable, Honeycomb, Barn door (if not included in Package 2), and a Set of Barn door and Honeycomb can be purchased separately.