SUMMIT APPLIANCE FF101W (01) PDF Document

Before the SUMMIT APPLIANCE FF101W is used, it must be properly positioned and installed as described in the manual. To reduce the risk of fire, electrical shock, or injury when using the appliance, follow basic precautions, including the following:

1. Plug into a grounded 3-prong outlet, do not remove grounding prong, do not use an adapter, and do not use an extension cord.
2. Replace all panels before operating.
3. It is recommended that a separate circuit serving only your appliance be provided. Use receptacles that cannot be turned off by a switch or pull chain.
4. Never clean appliance parts with flammable fluids. These fumes can create a fire hazard or explosion. And do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance. The fumes can create a fire hazard or explosion.
5. Do not connect or disconnect the electric plug when your hands are wet.
6. Unplug the appliance or disconnect power before cleaning or servicing. Failure to do so can result in electrical shock or death.
7. Do not attempt to repair or replace any part of your appliance unless it is specifically recommended in this manual. All other servicing should be referred to a qualified technician.
8. This appliance is CFC- and HFC-free and contains small quantities of Isobutane (R600a) which is environmentally friendly, but flammable. It does not damage the ozone layer, nor does it increase the greenhouse effect. Care must be taken during transportation and setting up of the appliance that no parts of the cooling system are damaged. Leaking coolant can ignite and may damage the eyes.

In the event of any damage from a coolant leak:

1. Avoid open flames and anything that creates a spark.
2. Disconnect from the power supply.
3. Air the room in which the appliance is located for several minutes.
4. Contact the Service Department for advice.

The more coolant there is in an appliance, the larger the room it should be installed in. If the appliance is in a small room, there is the danger of combustible gases building up. For every ounce of coolant, at least 325 cubic feet of room space is required. The amount of coolant in the appliance is stated on the data plate inside the appliance.

Follow these warnings when applicable to your model of the SUMMIT APPLIANCE FF101W:

• Use two or more people to move and install the appliance. Failure to do so can result in back or other injury.
• To ensure proper ventilation for your appliance, the front of the unit must be completely unobstructed.
• Choose a well-ventilated area with temperatures above 44°F (7°C) and below 90°F (32°C).
• The appliance should not be located next to ovens, grills, or other sources of high heat.
• The appliance must be installed with all electrical, water, and drain connections in accordance with state and local codes. A standard electrical supply (115 V AC only, 60 Hz), properly grounded in accordance with the National Electrical Code and local codes and ordinances, is required.
• Do not kink or pinch the power supply cord of the appliance.
• The size of the fuse (or circuit breaker) should be 15 amperes.
• It is important that the appliance be leveled in order to work properly. You may need to make several adjustments to level it.
• All installations must be in accordance with local plumbing code requirements.
• Make certain that the pipes are not pinched, kinked, or damaged during installation.
• Check for leaks after connection.
• Never allow children to operate, play with, or crawl inside the appliance.
• Do not use solvent-based cleaning agents or abrasives on the interior. These cleaners may damage or discolor the interior.
• Use this appliance only for its intended purpose as described in this Instruction Manual.
• Keep fingers out of the “pinch point” areas. Clearances between the door and cabinet are necessarily small. Be careful closing the door when children are in the area.

Before discarding your old appliance:

1. Take off the doors.
2. Leave the shelves in place so that children may not easily climb inside.

The refrigerated chamber of the SUMMIT APPLIANCE FF101W is suitable for storage of a variety of fruits, vegetables, beverages, and other food consumed in the short term. Additionally:

• Let any cooked foods cool to room temperature before storage.
• Seal any foods before storage.
• The glass shelves can be adjusted up or down for a reasonable amount of storage space and easy use.

The low temperature freezing chamber of the SUMMIT APPLIANCE FF101W may keep food fresh for a long time and is used to store frozen foods and making ice. The freezing chamber is suitable for storage of meat, fish, vegetables, and other foods not to be consumed in short term. Large portions of meat are should be divided into smaller pieces for easy access. Consume all foods within the proper shelf time.

Before using your SUMMIT APPLIANCE FF101W appliance:

1. Remove the exterior and interior packing.
2. Before connecting the appliance to the power source, let it stand upright for approximately 2 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation.
3. Clean the interior surface with lukewarm water using a soft cloth.
4. Install the handle on the door, if it is not already attached.

The appliance is designed for free standing installation for indoor use. CAUTION: This appliance is not designed for the storage of medicine or other medical products.

• Place your appliance on a floor that is strong enough to support it when it is fully loaded. To level the unit, adjust the front leveling legs.
• Keep 4″ of space between the back and the sides of the unit and 11” at the top to allow proper air circulation to cool the compressor and condenser.
• Keep away from heat and avoid direct sunlight. Do not place the unit in moist or watery places to prevent rust or reduction of insulating effect.
• Plug the appliance into an exclusive, properly grounded wall outlet.

Adjust the left and right front leveling feet to ensure your refrigerator-freezer is on a horizontal level.

• Turn the front leveling feet clockwise to increase the height of your refrigerator-freezer.
• Turn the front leveling feet counterclockwise to lower the height of your refrigerator-freezer.

WARNING: Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, have it replaced by a qualified electrician or an authorized service center.

This appliance should be properly grounded for your safety. The power cord of this appliance is equipped with a three-prong plug which mates with standard three-prong wall outlets to minimize the possibility of electrical shock.

• Do not under any circumstances cut or remove the third (ground) prong from the power cord supplied. For personal safety, this appliance must be properly grounded. Any questions concerning power and/or grounding should be directed toward a certified electrician or an authorized service center.
• This appliance requires a standard 115/120 Volt AC ~60Hz three-prong grounded electrical outlet. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. When a standard 2-prong wall outlet is encountered, it is your responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
• To prevent accidental injury, the cord should be secured behind the appliance and not left exposed or dangling.
• The appliance should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating label on the appliance. This provides the best performance and also prevents overloading house wiring circuits that could cause a fire hazard from overheating.
• Never unplug the appliance by pulling on the power cord. Always grip the plug firmly and pull straight out from the receptacle.
• Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. When moving the appliance, be careful not to damage the power cord.

Because of potential safety hazards under certain conditions, it is strongly recommended that you do not use an extension cord with this appliance. However, if you must use an extension cord, it is absolutely necessary that it be a UL/CUL-Listed, 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 115 volts and at least 10 amperes.

Tools needed for reversing the door swing on the SUMMIT APPLIANCE FF101W include:

• Phillips head screwdriver
• 5/16″ socket and rachet
• Flat-head screwdriver
• Masking tape
• Putty knife

If you find the direction of opening the door of the SUMMIT APPLIANCE FF101W appliance inconvenient, you can change it. Holes on the opposite side have already been prepared at the factory. To reverse your door, follow these instructions:

1. Unplug the appliance, and remove all items from the door shelves and the interior.
2. Remove the hinge hole cover from the top left side of the appliance.
3. Remove the upper hinge cover from the top right side of the appliance. Then, remove the hinge screws and upper hinge.
4. Lift the upper door off of the cabinet.
5. Place the upper door on a soft surface to ensure the door is not scratched or damaged.
6. Unscrew the middle hinge screws, and remove the middle hinge.
7. Remove the two hinge hold plugs, the screw, and screw cap from the middle beam on the opposite side of the appliance.
8. Remove the refrigerator door from the cabinet.
9. Carefully tip the unit back, and remove the adjusting feet, lower hinge screws, and the lower hinge assembly.
10. Install the lower hinge assembly on the other side of the cabinet, and install the adjusting feet again.
11. Dismantle the limit blocks and screws on the lower cover of the refrigerator and freezer door. Install them on the opposite side of both doors. Then, install the sleeve pipe on the upper cover of the refrigerator door on the other side.
12. Set the refrigerator door onto the lower hinge, and then install the middle hinge and hinge hole caps.
13. Set the freezer door onto the middle hinge, and then install the upper hinge to secure the freezer door, making sure to secure the hinge cover and hinge hole cover.

The control panel on the SUMMIT APPLIANCE FF101W features a SET key and five temperature settings.

• The settings cycle from 1 (coldest) to 5 (least cold) each time the SET key is pressed.

When an error occurs on the SUMMIT APPLIANCE FF101W, the corresponding LED light combination corresponds to the specific error. The error codes are detailed in the table below:

CAUTION: Be sure to unplug the appliance before cleaning to avoid the risk of electric shock.

To clean your SUMMIT APPLIANCE FF101W appliance:

• Dust accumulates behind and on the unit should be cleaned regularly to ensure cooling efficiency and energy consumption.
• Check the door gasket regularly to make sure there is no accumulated debris. Clean the door gasket with a soft cloth dampened with soapy water or diluted detergent.
• The interior of the refrigerator should be cleaned regularly to avoid any odor buildup. Do not use soap, detergent, scrub powder, spray cleaner, etc., as these may cause odors in the interior of the refrigerator.
• Use a soft cloth or sponge to clean the inside of the unit, using a solution of two tablespoons of baking soda and a quart of warm water. Then rinse with clean water, and then wipe clean with a soft towel. After cleaning, open the door and let the unit dry naturally before turning the power back on.
• For areas that are difficult to clean in (such as narrow gaps or corners), it is recommended to wipe them regularly with a soft rag or brush, or when necessary, an auxiliary tool (such as a thin stick) to ensure no contaminant or bacterial accumulation in these areas.
• Clean the bottle frame, shelves, and drawers with a soft cloth dampened with soapy water or diluted detergent. Dry with a soft cloth.
• Wipe the outer surface of the unit with a soft cloth dampened with soapy water or diluted detergent, and then wipe dry.
• Do not use hard brushes, clean steel balls, wire brushes, abrasives (such as toothpastes), organic solvents (such as alcohol, acetone, banana oil, etc.), boiling water, acid or alkaline items, which may damage the surface and interior of the unit. Boiling water and organic solvents such as benzene may deform or damage plastic parts.
• Do not rinse directly with water or other liquids during cleaning to avoid short circuits or potentially affect the electrical insulation.

To clean the glass shelves of the SUMMIT APPLIANCE FF101W:

1. Lift up the front of the glass shelf, and then pull the shelf out.
2. Clean as needed.
3. Reinstall the shelf by placing the rear of the shelf into position first. Then, carefully lower the front of the shelf into place.

The SUMMIT APPLIANCE FF101W appliance uses an automatic defrosting function. Frost formed due to the change of season or temperature may also be manually removed by disconnecting the appliance from the power supply or by wiping with a dry towel.

In case of a power failure with the SUMMIT APPLIANCE FF101W, even in warmer weather, foods inside the appliance can be kept for several hours; during the power failure, limit the times the door is opened, and do not add more fresh food into the appliance.

When moving the SUMMIT APPLIANCE FF101W:

• Before the unit is moved, remove all of the items stored inside, fix the glass shelves, drawers, freezing chamber drawers, etc. with tape, and tighten the leveling feet. Then, close the doors and fix them with tape.
• During moving, the appliance shall not be laid upside down or horizontally, or be vibrated; the inclination during movement shall be no more than 45°.

For vacations with the SUMMIT APPLIANCE FF101W:

• Short vacations: Leave the appliance operating during vacations of less than three weeks.
• Long vacations: If the appliance will not be used for several months, remove all items and turn the unit off. Clean and dry the interior thoroughly. To prevent odor and mold growth, leave the door open slightly, blocking it open if necessary.

If the SUMMIT APPLIANCE FF101W unit stops working, check the following:

• Check whether the appliance is connected to power or whether the plug is in well contact.
• Check whether the voltage is too low.
• Check whether there is a power failure or partial circuits have tripped.

If there is an odor inside the SUMMIT APPLIANCE FF101W unit:

• Tightly wrap food to prevent possible odor.
• Check whether there is any rotten food. Clean the inside of the appliance.

The compressor running too long on the SUMMIT APPLIANCE FF101W can be due to several reasons:

• Long operation of the compressor is normal in summer when the ambient temperature is high.
• It is not recommended to load a large amount of food in the appliance at one time. Cool food to room temperature before loading into the appliance.
• The doors are opened too frequently.

If the light fails to turn on in the SUMMIT APPLIANCE FF101W:

• Check whether the appliance is connected to power supply and whether the illuminating light is damaged.

If the doors on the SUMMIT APPLIANCE FF101W cannot be properly closed:

• The door is blocked by food packages.
• The appliance is not level.

If the SUMMIT APPLIANCE FF101W is making a loud noise, check the following:

• Check whether the floor is level and whether the appliance is placed stably. Check whether accessories are placed at proper locations.

If the door seal on the SUMMIT APPLIANCE FF101W fails to be tight:

• Remove foreign matters on the door seal.
• Heat the door seal and then cool it for restoration (Example: blow it with an electrical drier or use a hot towel for heating).

The water pan on the SUMMIT APPLIANCE FF101W may overflow for the following reasons:

• There is too much food in the chamber or the food stored contains too much water, resulting in heavy defrosting.
• The doors are not closed properly, resulting in frosting due to the entry of air and increased water due to defrosting.

Heat dissipation of the built-in condenser via the housing of the SUMMIT APPLIANCE FF101W is normal. When the housing becomes hot due to high ambient temperatures and the storage of too much food, it is recommended to provide sound ventilation to facilitate heat dissipation.

Condensation on the exterior surface and door seals of the SUMMIT APPLIANCE FF101W is normal when the ambient humidity is too high. Just wipe the condensate with a clean towel.

Regarding abnormal noise on the SUMMIT APPLIANCE FF101W:

• Buzz: The compressor may produce a buzzing noise during operation, and the buzzes are loud particularly upon start or stop. This is normal.
• Creak: Refrigerant flowing inside of the appliance may produce a creaking sound, which is normal.