STREETWIZE SWPP9 (01) PDF Document

The power booster is designed as a compact, durable and portable jump start system for vehicles and boats. This self-contained system will start most vehicles and boats without the need for a host vehicle or 230V AC power supply. This system can also be used as a safe, portable source of 12 DC electric power in remote locations and emergencies.

WARNING: THIS PRODUCT IS SUPPLIED WITH A MINIMAL CHARGE AT MANUFACTURE. IT IS UNABLE TO FUNCTION IN ANY WAY UNLESS THE UNIT IS FULLY CHARGED OVER A 12 HOUR PERIOD IMMEDIATELY AFTER PURCHASE. THIS IS ESSENTIAL BEFORE ANY USE!

Always wear eye protection when working on or around lead-acid batteries.

If splashed with battery acid:

Immediately wash effected area such as face and particularly the eyes with clean water. Continue washing the affected area and face until medical help arrives.

Lead-acid batteries generate hydrogen gas during normal operation. More gas is generated when the battery is charging. Hydrogen gas is:

1. Explosive

2. Poisonous to breathe

3. Highly flammable

To avoid explosion and/or the possibility of being splashed with battery acid:

1. Never allow the red and black clamps to touch each other nor to both touch the same metal object.

2. Only attempt to jump start a vehicle or boat in a well ventilated area.

3. Always connect the red(+) clamp to the positive(+) battery terminal of vehicle.

4. Do not connect the black(-) clamp to a moving metal part on the engine.

1. To avoid possible damage that may shorten the unit’s working life, protect this unit from direct sunlight, direct heat and/or moisture.

2. This system is designed to be used only on vehicle or boats with 12-Volt electric systems.

3. This system is not designed to be used as a replacement for a vehicle’s battery.

4. Air compressor caution: run compressor only for 10 minutes as a time continuously. Then leave off for 10 minutes before using again so that compressor can cool.

For maximum battery life, we recommend that your power station be kept fully charged at all times. If the battery is allowed to remain in a discharged state (flat), battery life maybe shortened. The following table shows the relationship of the frequency of use between recharging and the expected number of charge/recharge cycles.

Table 1.-Battery life

Table 2 shows the approximate recharging times you expect.

Table2.-Recharging times VS. Jump-starts

To check the battery charge, press the red button next to the volt meter. This will show you the battery’s internal charge level.

Plug the Adapter/charger into an AC power outlet and put the other (output DC 12v) end into the receptacle (beside DC charging LED No.11, see figure 1) on the front panel of your power booster until the battery meter shows full (14 to 15 DC).

Insert the cigarette lighter plug of the 12v DC/DC adapter/charger (No.8, see figure 1) into an 12v DC cigarette lighter receptacle (on your vehicle or boat) and put the other (output) end into the receptacle (beside DC charging LED No.11, see figure 1) on the front panel of your power booster until the battery meter shows full (14 to 15v DC).

To use your power booster as a 12v DC/DC power source:

1. Lift up the cover of 12v DC cigarette lighter receptacle (see No.1 of figure 1).

2. Insert the 12v DC cigarette lighter plug from the appliance into the 12V DC cigarette lighter receptacle on the side of your booster.

The following table gives an idea of what operation time you can expect when starting from a fully charged system for the STREETWIZE SWPP9:

For performance when using your power booster to jump start a vehicle or boat, please read and follow these step by step instructions:

1. Connect the red (+) crocodile clamp to the red (+) positive battery terminal of the vehicle or boat.

2. Connect the black(-)crocodile clamp to a non-moving metal part in the engine compartment, NOT to the(-)negative battery terminal due to possible damage to electronic control units (ECU’s), such as on-board computers and engine management systems.

3. Wait a minute or two.

4. Switch the vehicle or boat engine ignition to “start” for no more than 5 to 6 seconds.

5. If the vehicle or boat engine does not start, wait at least 3-minutes before trying again.

Under no circumstances allow the red and black clamps to touch each other.

1. Once the engine is running, disconnect the black(-)clamp first and return this cable to its stored position on the power booster.

2. Disconnect the red (+) clamp and return this cable to its stored position on the power booster.

3. As soon as possible connect your power booster system to the AC adapter, charge and recharge.

Caution: Run compressor only for 10 minutes at a time continuously. Then leave off for 10 minutes before using again so that compressor can cool.

1. For tyre inflation use the universal adapter that is attached permanently to the air hose. Place this adapter (No. C, see figure 2) onto the tyre valve system, press the adapter lever down to lock onto the valve system.

2. For inflation of leather balls, flotation devices, etc., use one of the plastic nozzles.

3. Check pressure gauge (No. A, see figure 2), determine the desired pressure.

4. Turn on power switch (No. B, see figure 2).

5. When the desired pressure is reached turn the compressor switch (No. B, see figure 2) off.

6. Remove the adapter (No. C, see figure 2) from tyre or other item being inflated.

To avoid possible damage that may shorten the unit’s working life, ensure that the red and black recharging wires stay attached with the jumper cables and are not switched.

The lead acid battery contained in the power booster jump start system should be recycled once it has expired. Please contact your local solid waste authority for recycling information.

Warning: Do NOT dispose of the battery in an open flame as this may result in an explosion.

Warning: Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to prevent shorting (shorting can result in injury or fire). Do NOT expose battery to fire or intense heat as it may explode.