Free English SONY CDX-GT410U (01) PDF document. Download the PDF, use the online viewer, or browse the FAQs for easy troubleshooting.
CLICK HERE TO DOWNLOAD SONY CDX-GT410U (01) PDF DOCUMENT
If this is not the document you want for this product, click here to see if we have any other documents for this product.
How to use the PDF below:
* Touchscreen: Swipe up/down with-in the PDF to scroll and pinch or spread with two fingers to zoom.
* Mouse: While your mouse is hovering over the PDF, use the mouse wheel to scroll and click on the – / + buttons at the bottom of the PDF to zoom.
How do I detach the front panel of the SONY CDX-GT410U?
You can detach the front panel of this unit to prevent theft.
1. Press the OFF button. The unit is turned off.
2. Press the front panel release button, then pull it off towards you.
How do I attach the front panel to the SONY CDX-GT410U?
Engage part A of the front panel with part B of the unit, as illustrated in the manual, and push the left side into position until it clicks.
How do I reset the SONY CDX-GT410U unit?
Before operating the unit for the first time, or after replacing the car battery or changing the connections, you must reset the unit. Pressing the RESET button will erase the clock setting and some stored contents.
1. Detach the front panel.
2. Press the RESET button (located behind the front panel) with a pointed object, such as a ballpoint pen.
How do I set the clock on the SONY CDX-GT410U?
The clock uses a 24-hour digital indication.
1. Press and hold the select button. The setup display appears.
2. Press the select button repeatedly until “CLOCK-ADJ” appears.
3. Press the SEEK + button. The hour indication flashes.
4. Rotate the volume control dial to set the hour and minute. To move the digital indication, press SEEK -/+.
5. Press the select button. The setup is complete and the clock starts.
How do I store radio stations automatically (BTM) on the SONY CDX-GT410U?
The unit selects strong signal stations and stores them. You can store up to 6 stations per band (FM1, FM2, FM3, MW, or LW).
1. Press the SOURCE button repeatedly until “TUNER” appears. To change the band, press the MODE button repeatedly. You can select from FM1, FM2, FM3, MW or LW.
2. Press and hold the select button. The setup display appears.
3. Press the select button repeatedly until “BTM” appears.
4. Press the SEEK + button. The unit stores stations in order of frequency on the number buttons. A beep sounds when the setting is stored.
How do I adjust the sound characteristics (Balance/Fader/Subwoofer) on the SONY CDX-GT410U?
You can adjust the balance, fader, and subwoofer volume.
1. Press the select button repeatedly until “BAL,” “FAD” or “SUB” appears. The item changes as follows: LOW -> MID -> HI -> BAL (left-right) -> FAD (front-rear) -> SUB (subwoofer volume) -> AUX.
2. Rotate the volume control dial to adjust the selected item.
After 3 seconds, the setting is complete and the display returns to normal play/reception mode.
How do I customize the equalizer curve (EQ3) on the SONY CDX-GT410U?
“CUSTOM” of EQ3 allows you to make your own equalizer settings.
1. Select a source, then press the EQ3 button repeatedly to select “CUSTOM.”
2. Press the select button repeatedly until “LOW,” “MID” or “HI” appears.
3. Rotate the volume control dial to adjust the selected item. The volume level is adjustable in 1 dB steps, from –10 dB to +10 dB.
4. Repeat steps 2 and 3 to adjust the equalizer curve.
To restore the factory-set equalizer curve, press and hold the select button before the setting is complete. After 3 seconds, the setting is complete and the display returns to normal play/reception mode.
How do I adjust setup items on the SONY CDX-GT410U?
1. Press and hold the select button. The setup display appears.
2. Press the select button repeatedly until the desired item appears.
3. Rotate the volume control dial to select the setting (example “ON” or “OFF”).
4. Press and hold the select button. The setup is complete and the display returns to normal play/reception mode.
What setup items can be adjusted on the SONY CDX-GT410U?
The following items can be set:
CLOCK-ADJ (Clock Adjust): To set the clock.
CT (Clock Time): To set “CT-ON” or “CT-OFF”.
BEEP: To set “BEEP-ON” or “BEEP-OFF.”
AUX-A (AUX Audio): To turn the AUX source display “AUX-A-ON” or “AUX-A-OFF.”
A.OFF (Auto Off): To shut off automatically after a desired time when the unit is turned off: “A.OFF-NO”, “A.OFF-30S (Seconds),” “A.OFF-30M (Minutes)” or “A.OFF-60M (Minutes).”
SUB/REAR: To switch the audio output. “SUB-OUT” to output to a subwoofer. “REAR-OUT” to output to a power amplifier.
DEMO (Demonstration): To set “DEMO-ON” or “DEMO-OFF.”
DIM (Dimmer): To change the brightness of the display. “DIM-ON” to dim the display. “DIM-OFF” to deactivate the dimmer.
ILM (Illumination): To change the illumination color: “ILM-1” or “ILM-2.”
A.SCRL (Auto Scroll): To scroll long displayed item automatically when the album/track is changed. “A.SCRL-ON” to scroll. “A.SCRL-OFF” to not scroll.
LOCAL (Local Seek Mode): “LOCAL-ON” to only tune into stations with stronger signals. “LOCAL-OFF” to tune normal reception.
MONO (Monaural Mode): To improve poor FM reception, select monaural reception mode. “MONO-ON” to hear stereo broadcast in monaural. “MONO-OFF” to hear stereo broadcast in stereo.
REG (Regional): To set “REG-ON” or “REG-OFF.”
LPF (Low Pass Filter): To select the subwoofer cut-off frequency: “LPF OFF”, “LPF125Hz” or “LPF 78Hz.”
BTM: To store radio stations automatically.
How do I use Repeat and Shuffle play for CDs on the SONY CDX-GT410U?
During playback, press (3) (REP) or (4) (SHUF) repeatedly until the desired setting appears.
Selectable Options:
| Select | To play |
|---|---|
| TRACK | track repeatedly. |
| ALBUM | album repeatedly. (When an MP3/WMA/AAC is played) |
| GROUP | group repeatedly. (When an ATRAC CD is played) |
| SHUF ALBUM | album in random order. (When an MP3/WMA/AAC is played) |
| SHUF GROUP | group in random order. (When an ATRAC CD is played) |
| SHUF DISC | disc in random order. |
To return to normal play mode, select the OFF setting or “SHUF OFF.”
How do I play music from a USB device on the SONY CDX-GT410U?
1. Connect the USB device to the USB terminal.
2. Playback starts.
Press the OFF button to stop playback.
Note: Before removing a USB device, be sure to stop playback first. If you remove your USB device during playback, data in the USB device may be damaged.
How do I use Repeat and Shuffle play for a Mass Storage Class USB audio device on the SONY CDX-GT410U?
During playback, press (3) (REP) or (4) (SHUF) repeatedly until the desired setting appears.
Selectable Options:
| Select | To play |
|---|---|
| TRACK | track repeatedly. |
| ALBUM | album repeatedly. |
| SHUF ALBUM | album in random order. |
| SHUF DEVICE | device in random order. |
To return to normal play mode, select the OFF setting or “SHUF OFF.”
How do I listen to music on a “Walkman” (ATRAC Audio Device) using the SONY CDX-GT410U?
Selecting Items:
During playback, press the MODE button repeatedly until the desired setting appears. The item changes as follows: ALB (Album) -> ART (Artist) -> PLY (Playlist).
Repeat and Shuffle Play:
During playback, press (3) (REP) or (4) (SHUF) repeatedly until the desired setting appears.
| Select | To play |
|---|---|
| TRACK | track repeatedly. |
| ALBUM | album repeatedly. |
| ARTIST | artist repeatedly. |
| PLAYLIST | playlist repeatedly. |
| SHUF ALBUM | album in random order. |
| SHUF ARTIST | artist in random order. |
| SHUF PLAYLIST | playlist in random order. |
| SHUF DEVICE | device in random order. |
To return to normal play mode, select the OFF setting or “SHUF OFF.”
CLICK HERE TO DOWNLOAD SONY CDX-GT410U (01) PDF DOCUMENT