SONY BRAVIA KDL-46XBR4 (04) PDF MANUAL

When installing the Mounting Hook on the TV, use the screw locations specified in the table below. When installing the TV onto the Base Bracket, use the hook locations specified.

Model Name	Screw location	Hook location
KDL-40XBR4	e, g	b
KDL-46XBR4	e, g	b
KDL-52XBR4	d, g	a
KDL-40XBR5	e, g	b
KDL-46XBR5	e, g	b
KDL-52XBR5	d, g	a

* Hook position “c” cannot be used for the models in the table above.

For product protection and safety reasons, Sony strongly recommends that wall-mounting of your TV be performed by Sony dealers or licensed contractors. Do not attempt to install it yourself.

Sufficient expertise is required in installing this product, especially to determine the strength of the wall for withstanding the TV’s weight. Be sure to entrust the attachment of this product to the wall to Sony dealers or licensed contractors and pay adequate attention to safety during the installation. Sony is not liable for any damage or injury caused by mishandling or improper installation.

Verify your TV’s model number and be sure to use the bracket specified for your model only. Refer to the Steps on this leaflet along with the Instructions supplied with the SU-WL500 Wall-Mount Bracket, to properly carry out the installation.

Step 1: Checking the parts required for the installation

Open the Wall-Mount Bracket package and check the contents for all required parts along with the Instructions.

Step 2: Deciding on the installation location

Decide where you want to install your TV. Refer to the TV installation dimensions table and the Instructions for SU-WL500.

Step 3: Installing the Base Bracket on the wall

Refer to the Instructions for SU-WL500.

Step 4: Preparing for the installation of the TV

Before detaching the Table-Top Stand, disconnect all the cables from the TV. Refer to Operating Instructions supplied with the TV set for removing the Table-Top Stand. For mounting hook installation, refer to the Screw and Hook locations diagram/table.

Step 5: Installing the TV on the wall

Refer to the Instructions for SU-WL500.

Your KDL-40XBR4/KDL-40XBR5/KDL-46XBR4/KDL-46XBR5/KDL-52XBR4/KDL-52XBR5 can be wall-mounted using the SU-WL500 Wall-Mount Bracket (sold separately).

The wall that the TV will be installed on should be capable of supporting a weight of at least four times that of the TV. Refer to your TV’s instructions for its weight. Sufficient expertise is required to determine the strength of the wall for withstanding the TV’s weight.

TV installation dimensions table

Unit: mm (inches)

Model Name	Display dimensions		Screen center dimensions		Length for each mounting angle
	A	B	C	D	Angle (0°)		Angle (20°)
					E	F	G	H
KDL-40XBR4	1,111 (43 3/4)	657 (25 7/8)	176 (7)	509 (20 1/8)	181 (7 1/4)	349 (13 3/4)	621 (24 1/2)	550 (21 3/4)
KDL-46XBR4	1,262 (49 3/4)	734 (29)	128 (5 1/8)	500 (19 3/4)	181 (7 1/4)	378 (15)	694 (27 3/8)	542 (21 3/8)
KDL-52XBR4	1,415 (55 3/4)	827 (32 5/8)	73 (2 7/8)	491 (19 3/8)	183 (7 1/4)	415 (16 3/8)	781 (30 3/4)	533 (21)
KDL-40XBR5	1,111 (43 3/4)	657 (25 7/8)	176 (7)	509 (20 1/8)	183 (7 1/4)	349 (13 3/4)	621 (24 1/2)	550 (21 3/4)
KDL-46XBR5	1,262 (49 3/4)	734 (29)	128 (5 1/8)	500 (19 3/4)	183 (7 1/4)	378 (15)	694 (27 3/8)	542 (21 3/8)
KDL-52XBR5	1,415 (55 3/4)	827 (32 5/8)	73 (2 7/8)	491 (19 3/8)	185 (7 3/8)	415 (16 3/8)	781 (30 3/4)	533 (21)

Figures in the above table may differ slightly depending on the installation.